1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changed parameter (AOL) in table I from 96 dB to 94 dB. 91-09-30 Don Cool B Update drawing requirements to MIL-PRF-38534. 01-02-02 Raymond Monnin C Table I, Supply current (IS) test, subgroup 2 test limit: change 11.0 mA to 12.0 mA. Correct parag
2、raphs 4.2.a.2 and 4.3.3.b.2. 05-07-18 Raymond Monnin D Paragraph 1.3, junction temperature, change +200C to +175C. Table I, Stability/noise (EN) test, conditions column, change CL= 10 nF to CL= 1 nF. 05-11-22 Raymond Monnin E Added footnote 1 to table II, under group C end-point electricals. Updated
3、 drawing paragraphs. -sld 11-12-06 Charles F. Saffle THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHEET REV SHEET REV STATUS REV E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Steve Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.land
4、andmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Gary Zahn THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Don Cool MICROCIRCUIT, HYBRID, LINEAR, HIGH POWER, OPERATIONAL AMPLIFIER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-03-29 AMSC N/A REVISION
5、 LEVEL E SIZE A CAGE CODE 67268 5962-90723 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E047-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90723 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL
6、 E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a cho
7、ice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 90723 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see
8、1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) ide
9、ntify the circuit function as follows: Device type Generic number Circuit function 01 PA08M, MIOP42116 Power operational amplifier 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements
10、of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applic
11、ations. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible li
12、mited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of
13、 that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manu
14、facturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 8 Flange mount 1.2.5 Lead finish. The l
15、ead finish shall be as specified in MIL-PRF-38534. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90723 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.3 Abso
16、lute maximum ratings. Supply voltage (VS) . 150 V dc Output current (IO) . 200 mA Power dissipation (PD) 1/ 17.5 W Input voltage (differential) . 50 V dc Input voltage (common mode) 150 V dc Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) . +175C Storage temperature range
17、. -65C to +150C 1.4 Recommended operating conditions. Supply voltage (VS) . 100 V dc Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing t
18、o the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method St
19、andard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.
20、dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothin
21、g in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with M
22、IL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requ
23、irements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 1/ Derate at 6.5C/W above case temperature (TC) of +25C. Provided by IHSNot for R
24、esaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90723 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3.2 Design, construction, and physical dimensions. The design, construction, and ph
25、ysical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. U
26、nless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrica
27、l tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the
28、 general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summa
29、ry of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certif
30、icate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certifica
31、te of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the dev
32、ice manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-
33、883. (1) Test condition D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and powe
34、r dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parame
35、ter tests prior to burn-in are optional at the discretion of the manufacturer. c. Constant acceleration may be performed after burn-in upon approval by the qualifying activity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRA
36、WING SIZE A 5962-90723 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C VS= 100 V dc Group A subgroups Device type Limits Unit unless otherwise specified Min Max Sup
37、ply current ISVIN= 0 V dc, G = 100, 2/ RCL= 6.5 , VCM= 0 V dc 1 01 8.5 mA 2 12.0 3 9.5 Input offset voltage VOSVIN= 0 V dc, G = 100, 2/ VS= 15 V dc , RCL= 6.5 1 01 -3.7 +3.7 mV 2 -6.7 +6.7 3 -6.1 +6.1 VIN= 0 V dc, G = 100, 2/ VS= 100 V dc , RCL= 6.5 1 -2.0 +2.0 mV 2 -5.0 +5.0 3 -4.5 +4.5 VIN= 0 V dc
38、, G = 100, 2/ VS= 150 V dc , RCL= 6.5 1 -3.0 +3.0 mV 2 -6.0 +6.0 3 -5.4 +5.4 Input bias current, +IN +IBVIN= 0 V dc, RBIAS 100 M 1,3 01 50.0 pA 2 10.0 nA Input bias current, -IN -IBVIN= 0 V dc, RBIAS 100 M 1,3 01 50.0 pA 2 10.0 nA Input offset currentIOSVIN= 0 V dc, RBIAS 100 M 1,3 01 50.0 pA 2 10.0
39、 nA Output voltage VOVS= 150 V dc, IO= 29 mA, RL= 5 k 4,5,6 01 145 V VS= 90 V dc, IO= 80 mA, RL= 1 k, TC= +25C, +125C 4,5 80 V VS= 31 V dc, IO= 150 mA, RL= 100 , TC= +25C, +125C 4,5 15 V VS= 90 V dc, IO= 70 mA, RL= 1 k, TC= -55C 6 70 V See footnotes at end of table. Provided by IHSNot for ResaleNo r
40、eproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90723 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C
41、TC +125C VS= 100 V dc Group A subgroups Device type Limits Unit unless otherwise specified Min Max Current limits ICLRL= 100 , RCL= 6.5 , 2/ VS= 30 V dc, TC= +25C 4 01 75 125 mA Stability/noise ENG = 1, CL= 1 nF 4,5,6 01 1.0 mV Slew rate SRRL= 5 k, VIN 4 VP-P 4,5,6 01 20 100 V/s Open loop gain AOLRL
42、= 5 k, f = 15 Hz, VIN 0.4 VP-P 4,5,6 01 94 dB Common mode rejection CMR VS= 32.5 V dc, f = dc, VCM= 22.5 V dc 4,5,6 01 90 dB 1/ During all group A testing, terminal connection BAL (pin 7) is left open. 2/ A current limiting resistor (RCL) is connected between CL+ the output and CL- the output during
43、 these tests. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90723 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Min
44、 Max Min Max A 38.35 39.37 1.510 1.550 B 19.30 19.81 .760 .780 C 7.37 .290 D 0.97 1.07 .038 .042 E 2.03 2.54 .080 .100 F 40 BSC 40 BSC G 12.7 BSC .500 BSC H 30.12 BSC 1.186 BSC J 15.06 BSC .593 BSC K 11.68 12.70 .460 .500 Q 3.84 4.09 .151 .161 R 25.15 25.65.990 1.010 NOTES: 1. The U. S. preferred sy
45、stem of measurement is the metric SI. This case outline was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound shall take precedence. 2. Pin numbers are for reference and may not be marked on package. FIGURE 1.
46、Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90723 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outline X Terminal num
47、ber Terminal symbol 1 2 3 4 5 6 7 8 Output +Current limit (CL+) +VS +IN -IN -VS Balance (BAL) -Current limit (CL-) FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90723 DLA LAN
48、D AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters - Final electrical parameters 1*, 2, 3, 4, 5, 6 Group A test requirements 1, 2, 3,
