1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to the latest requirements. -sld 06-04-10 Raymond Monnin REV SHEET REV SHEET REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Steve Duncan DEFENSE SUPPLY CENTER COLUMB
2、US STANDARD MICROCIRCUIT DRAWING CHECKED BY Gary Zahn COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil/ THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Gregory Lude MICROCIRCUIT, HYBRID, LINEAR, 12-BIT, 8-CHANNEL, DATA ACQUISTION SYSTEM AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAW
3、ING APPROVAL DATE 92-05-14 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-90797 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E368-06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90797 DEFENSE SUPPLY CEN
4、TER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Pa
5、rt or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 90797 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator
6、 (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA
7、 device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 MN7140 12-bit, 8 channel, data acquistion system 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product ass
8、urance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class
9、available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class
10、H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C and D). E Designates devices which are based upon one of the other classes (K
11、, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer spec
12、ified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90797 DEFENS
13、E SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 40 Dual-in-line 1.2.5 Lead finis
14、h. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage range (VCC) . -0.5 V dc to +18 V dc Negative supply voltage range (VEE) +0.5 V dc to -18 V dc Logic supply voltage range (VDD) . -0.5 V dc to +16 V dc Analog input channels 15 V Digita
15、l input voltage range . 0.0 V dc to +5.5 V dc Power dissipation (PD) . 1.430 W Thermal resistance, junction-to-case(JC) 30C/W Thermal resistance, junction-to-ambient (JA) 45C/W Lead temperature (soldering, 10 seconds). +300C Storage temperature range -65C to +150C Junction temperature (TJ) +175C 1.4
16、 Recommended operating conditions. Positive supply voltage range (VCC) . +14.55 V dc to +15.45 V dc Negative supply voltage range (VEE) -14.55 V dc to -15.45 V dc Logic supply voltage range (VDD) . +4.75 V dc to +5.25 V dc Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENT
17、S 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE
18、 SPECIFICATIONS MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Mic
19、rocircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _
20、1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DR
21、AWING SIZE A 5962-90797 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in
22、this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PR
23、F-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requireme
24、nts as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physi
25、cal dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Digital output codes. The digital output c
26、odes shall be as specified on figure 3. 3.2.4 Timing diagram. The timing diagram shall be as specified on figure 4. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full spec
27、ified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534.
28、 The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data
29、 (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision le
30、vel control by the manufacturer and be made available to the preparing activity (DSCC-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DSCC
31、-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sa
32、mpling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. Provided by IHSNot for ResaleN
33、o reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90797 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits Unit Test Symbol Conditi
34、ons 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Min Max VIH IIH= 5 A 2.4 Digital input logic levels VIL IIL= 5 A 0.8 V IIH VIH= 2.4 V -5.0 +5.0 Digital input currents IIL VIL= 0.8 V -5.0 +5.0 A VIHIIH= 10 A 4.0 Mux enable logic levels VILIIL= 10 A 0.8 V IIH VIH= 4.0 V -1
35、0 +10 Mux enable input currents IIL VIL= 0.8 V -10 +10 A ICCVCC= +15 V +40 IEE VEE= -15 V -50 Power supply drain currents IDD VCC= +5 V +16 mA Power dissipation PD1,2,3 1.43 W RBIAS= 1.8 K 1 25 Input bias current 2/ IBRBIAS= 2.0 K 2,3 250 nA Input impedance 2/ ZIN 1,2,3 100 M 4 -0.1 +0.1 Full scale
36、absolute accuracy error 3/ +VFS -VFSLSB MSB *000 0000 0000 *111 1111 1111 5,6 -0.4 +0.4 %FSR 4 -0.1 +0.1 Zero error 3/ VZ LSB MSB * * * * * * 5,6 01 -0.4 +0.4 %FSR See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR
37、D MICROCIRCUIT DRAWING SIZE A 5962-90797 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Dev
38、ice type Min Max Unit 4 -0.5 +0.5 Linearity error LIN 5,6 -1.0 +1.0 LSB VOH IO= -360 A +2.4 Digital output logic levels VOL IO=+360 A 1,2,3 +0.4 V A/D conversion time tcWidth of status pulse 4,5,6 50 Acquistion time tAQC20 V step to 0.01 percent 4,5,6 01 10 s 1/ VCC= +15 V dc, VEE= -15 V dc, and VDD
39、= 5 V dc, unless otherwise specified. 2/ Parameter shall be tested as part of device characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. 3/ * The output will change from a “1“ to a “0“ or vice v
40、ersa as the analog input passes through the voltages listed in the limit columns. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90797 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL
41、A SHEET 7 DSCC FORM 2234 APR 97 FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90797 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 A
42、PR 97 Millimeters Inches Symbol Min Max Min Max A 3.61 4.62 .142 .182 b 0.41 0.51 .016 .020 C 0.20 0.33 .008 .013 D 52.68 53.75 2.074 2.116 D1 48.13 48.39 1.895 1.905 e 2.41 2.67 .095 .105 eA 15.11 15.38 .595 .605 e1 2.03 2.79 .080 .110 E 19.56 20.57 .770 .810 L 5.08 5.84 .200 .230 Q 0.38 0.89 .015
43、.035 S 2.16 2.92 .085 .115 NOTE: The U.S. government preferred system of measurement is the metric SI. This item was designed using inch-pound units of measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch- pound units shall rule. FIGURE 1. Case outli
44、ne - Continued.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90797 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 Device Type All Case outline X Term
45、inal number Pin Function 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Channel 4 input Channel 5 input Channel 6 input Channel 7 input Address output (A1) Address output (A2) Address output (A4) Address output (A8) Mux output, amplifie
46、r in (+) Instrumentation amplifier input (-) Trigger input Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 (MSB) Ground Offset adjust VCCVEE Gain adjust VDDBit 12 (LSB) Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Status output (E.O.C.) Address mode Address input (A8) Address input (A4) Address input (A2) Address input (A1)
47、 Mux enable Channel 0 input Channel 1 input Channel 2 input Channel 3 input FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90797 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO
48、43218-3990 REVISION LEVEL A SHEET 10 DSCC FORM 2234 APR 97 Analog input Digital output +10.000 + 9.9951 + 0.0098 MSB LSB 0000 0000 0000 0000 0000 000* see note 0111 1111 11* see note +0.0049 0.0000 -0.0049 0111 1111 111* see note * * * see note 1000 0000 000* see note -0.0098 -9.9951 -10.000 1000 0000 00* see
