1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update to reflect latest changes in format and requirements. Editorial changes throughout. -les 04-09-13 Raymond Monnin B Update drawing as part of 5 year review. - jt 12-10-15 C. SAFFLE THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED.
2、REV SHEET REV SHEET REV STATUS REV B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Larry T. Gauder DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEP
3、ARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Thanh V. Nguyen APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, BIPOLAR, LOW-POWER SCHOTTKY, TTL, 8-BIT SUCCESSIVE APPROXIMATION REGISTER, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-02-08 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE
4、67268 5962-90800 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E466-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90800 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234
5、APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). Wh
6、en available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90800 01 M E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4)
7、 Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA l
8、evels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as follows: Device type Generic number Circuit function Clock frequency 01 54LS502 8-bit successive 25 MHz approximation register 1.2.3 De
9、vice class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with M
10、IL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 dual-in-line F GDFP2-F16 or CDFP3-F16 16
11、 flat 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90800 DLA
12、LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) . +7.0 V dc Input voltage (VIN) . +7.0 V dc Storage temperature -65C to +150C Continuous power dissipation (PD) 500 mW 2/ Lead temperature (soldering, 10 s
13、econds) +300C Junction temperature (TJ) +175C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Minimum high level input voltage (VIH) 2.0 V dc Maximum low level input voltage (VIL) 0.7 V dc Maximum hi
14、gh level output current (IOH) -4.0 mA Maximum low level output current (IOL) 4.0 mA Ambient operating temperature range (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing
15、 to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 -
16、 Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/a
17、ssist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence.
18、Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modifie
19、d in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and
20、 as specified herein. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Continuous power dissipation is defined as VCCx ICC, and must withstand the added PDdue to short
21、 circuit test e.g., IOSProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90800 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3.2 Design, construction, and physic
22、al dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal co
23、nnections and descriptions. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth tables shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Test circuit and switching waveforms. The test circuit and sw
24、itching waveforms shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over th
25、e full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addi
26、tion, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Mar
27、king for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. Th
28、e compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.
29、1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of sup
30、ply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required f
31、or device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product
32、(see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufa
33、cturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 12 (see MIL-PRF-38
34、535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90800 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance character
35、istics. Test Symbol Conditions -55C TA +125C 4.5 V VCC 5.5 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max High level output voltage VOHVCC= 4.5 V, VIL= 0.7 V, 1, 2, 3 All 2.5 V IOH = -0.4 mA, VIH= 2.0 V Low level output voltage VOLVCC= 4.5 V, IOL = 4.0 mA 1, 2, 3 All
36、0.4 V Input clamp voltage VICVCC= 4.5 V IIN = -18 mA 1, 2, 3 All -1.5 V High level input current IIH1VCC= 5.5 V VIN= 2.7 V 1, 2, 3 All 20 A IIH2VIN= 10 V 100 Low level input current IILVCC= 5.5 V, VIN= 0.4 V 1, 2, 3 All -0.06 -1.2 mA Short circuit output current IOSVCC= 5.5 V, VOUT= 0.0 V 1/ 1, 2, 3
37、 All -20 -100 mA Supply current ICCVCC= 5.5 V 1, 2, 3 All 65 mA Functional tests See 4.4.1b, VCC= 4.5 and 5.5 V 7, 8 All Maximum clock fMAX VCC= 5.0 V, 9 All 25 MHz frequency RL= 2 k, 10, 11 20 Propagation delay time, tPLHCL= 50 pF, 9 All 2.0 40 ns CP to Qn or CC See figure 4 10, 11 2.0 52 tPHL9 All
38、 2.0 30 ns 10, 11 2.0 39 Setup time, S or D ts(H) 9 All 5.0 ns to CP 10, 11 10 ts(L) 9 All 5.0 ns 10, 11 10 Hold time, S or D th(H) 9 All 5.0 ns to CP 10, 11 10 th(L) 9 All 5.0 ns 10, 11 10 Clock pulse width tw(H) 9 All 20 ns 10, 11 25 tw(L) 9 All 20 ns 10, 11 25 1/ Not more than one output should b
39、e tested at one time and duration of the test condition should not exceed one second. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90800 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHE
40、ET 6 DSCC FORM 2234 APR 97 Device type 01 Case outlines E and F Terminal number Terminal symbol 1 QD 2 CC 3 Q0 4 Q1 5 Q2 6 Q3 7 D 8 GND 9 CP 10 S 11 Q4 12 Q5 13 Q6 14 Q7 15 Q7 16 VCCTerminal connections Pin names Description D Serial data input S Start input (active low) CP Clock pulse input (active
41、 rising edge) QD Synchronized serial data output CC Conversion complete output (active low) Q0-Q7 Parallel register outputs Q7 Complement of Q7 output Terminal descriptions FIGURE 1. Terminal connections and descriptions. Provided by IHSNot for ResaleNo reproduction or networking permitted without l
42、icense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90800 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Time tnInputs Outputs D S QD Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 CC 0 X L X X X X X X X X X X 1 D7 H X L H H H H H H H H 2 D6 H D7 D7 L H H H H H H H
43、 3 D5 H D6 D7 D6 L H H H H H H 4 D4 H D5 D7 D6 D5 L H H H H H 5 D3 H D4 D7 D6 D5 D4 L H H H H 6 D2 H D3 D7 D6 D5 D4 D3 L H H H 7 D1 H D2 D7 D6 D5 D4 D3 D2 L H H 8 D0 H D1 D7 D6 D5 D4 D3 D2 D1 L H 9 X H D0 D7 D6 D5 D4 D3 D2 D1 D0 L 10 X H X D7 D6 D5 D4 D3 D2 D1 D0 L H = High voltage level. L = Low vo
44、ltage level. X = Irrelevant. FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90800 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 NOTE: C
45、ell logic is repeated for register stages Q5 to Q1. FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90800 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC
46、 FORM 2234 APR 97 FIGURE 4. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90800 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 10 DSCC FORM 2234
47、 APR 97 NOTES: 1. CLincludes probe and jig capacitance. 2. The pulse generator shall have the following characteristics: PRR = 1 MHz, tr= tf 15 ns, duty cycle = 50%. 3. All diodes are 1N3064 or equivalent. FIGURE 4. Test circuit and switching waveforms - Continued. Provided by IHSNot for ResaleNo re
48、production or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90800 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 11 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device manufacturers Quality Management
