1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add case outline U. Add vendor CAGE 69210 for device type 01UX. Editorial changes throughout. 93-04-27 M. A. FRYE B Add new footnote 2/ to VLT, VRIN, VRIT, VON, ROtests and explanation as specified under Table I. Changes in accordance with NOR 59
2、62-R138-96. 96-06-06 M. A. FRYE C Add a minimum limit of .000 to the maximum .065 inch limit for case outline U as specified under Figure 1. Changes in accordance with NOR 5962-R187-96. 96-08-12 R. MONNIN D Add case outline E for vendor CAGE 27014. Update boilerplate. Editorial changes throughout. R
3、edrawn. 97-05-16 R. MONNIN E Add case outline X for vendor CAGE 27014. Make changes to 1.2.4, theta JC, theta JA as specified in 1.3, dropout voltage test as specified in table I, and figure 1. - ro 99-08-11 R. MONNIN F Add case outlines M and N for vendor CAGE 69210. - ro 02-03-29 R. MONNIN G Updat
4、ing boilerplate paragraphs to reflect current requirements. - ro 09-04-15 R. HEBER THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY JOSEPH A. KERBY CHECKED BY CHARLES E
5、. BESORE DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil APPROVED BY MICHAEL A. FRYE STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-12-18 MICROCIRCUIT, LINEAR, 15-VO
6、LT REGULATOR, MONOLITHIC SILICON AMSC N/A REVISION LEVEL G SIZE A CAGE CODE 67268 5962-90885 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E072-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90885 DEFENSE SUPP
7、LY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead
8、 finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90885 01 Q E A Federal stock class designator RHA designator
9、 (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. D
10、evice class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit fu
11、nction 01 LM2940-15 1.0 A, low dropout, 15-volt regulator 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 c
12、ompliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package styl
13、e E GDIP1-T16 or CDIP2-T16 16 Dual-in-line M See figure 1 3 Flange mount, glass sealed with gullwing leads N CBCC1-N3 3 Bottom terminal chip carrier U See figure 1 3 TO-257, single row flange mount with isolated tab, glass sealed X GDFP1-G16 16 Flat pack with gullwing leads Y MBFM1-P2 2 Flange mount
14、 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90885 DEFENSE S
15、UPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Input voltage (VIN): Survival voltage ( 100 ms ) 60 V dc Operational voltage . 26 V dc Internal power dissipation (PD) . Internally limited Storage temperature range . -65C
16、 to +150C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) . +150C Thermal resistance, junction-to-case (JC): Cases E and U 3C/W Case M 7.6C/W Case N 5.9C/W Cases X and Y . 5C/W Thermal resistance, junction-to-ambient (JA): Case E . 73C/W Case M 60C/W Case N 80C/W Case U 50C/
17、W Case X . 122C/W Case Y . 40C/W 1.4 Recommended operating conditions. Ambient operating temperature range (TA) . -55C to +125C Output current (IO) 1 A Input voltage (VIN) 20 V dc 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards,
18、and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPA
19、RTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these d
20、ocuments are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
21、maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90885 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC FORM
22、 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3
23、. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit,
24、 or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions
25、shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as spec
26、ified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperatu
27、re range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may al
28、so be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V sh
29、all be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class
30、 M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a c
31、ertificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufact
32、urers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for d
33、evice class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is requir
34、ed for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available
35、onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 52 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license
36、from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90885 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C VIN= 20 V, IO= 1 A, Group A subgroups Device type
37、 Limits 1/ Unit COUT= 22 F unless otherwise specified Min Max Output voltage VOUTVIN= 20 V, IO= 5 mA 1 01 14.55 15.45 V 2,3 14.25 15.75 VIN= 16.75 V, IO= 5 mA 1 01 14.55 15.45 V 2,3 14.25 15.75 VIN= 17 V, IO= 5 mA 1 01 14.55 15.45 V 2,3 14.25 15.75 VIN= 26 V, IO= 5 mA 1 01 14.55 15.45 V 2,3 14.25 15
38、.75 VIN= 20 V, IO= 1 A 1 01 14.55 15.45 V 2,3 14.25 15.75 VIN= 16.75 V, IO= 1 A 1 01 14.55 15.45 V 2,3 14.25 15.75 VIN= 16.75 V, IO= 50 mA 1 01 14.55 15.45 V 2,3 14.25 15.75 VIN= 20 V, IO= 50 mA 1 01 14.55 14.45 V 2,3 14.25 15.75 Maximum line transient VLTVO 16 V, 2/ RO= 100 , t = 20 ms 1,2,3 01 40
39、V Reverse polarity input voltage dc VRINRO= 100 2/ 1,2,3 01 -15 V Reverse polarity input voltage transient VRITRO= 100 , t = 20 ms 2/ 1,2,3 01 -45 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT
40、DRAWING SIZE A 5962-90885 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C VIN= 20 V, IO= 1 A, Group A subgroups Device type Limits 1/ Unit COUT= 22
41、F unless otherwise specified Min Max Quiescent current IQVIN= 20 V, IO= 5 mA 1 01 0 15 mA 2,3 0 20 VIN= 17 V, IO= 5 mA 1 01 0 15 mA 2,3 0 20 VIN= 26 V, IO= 5 mA 1 01 0 15 mA 2,3 0 20 VIN= 20 V, IO= 1 A 1 01 0 50 mA 2,3 0 60 Line regulation VRLINE17 V VIN 26 V, 1 01 95 mV IO= 5 mA 2,3 150 Load regula
42、tion VRLOADVIN= 20 V, 1 01 150 mV 50 mA IO 1 A 2,3 240 Dropout voltage VDOIO= 1 A 1 01 0 0.7 V 2,3 0 1 IO= 100 mA 1 01 0 200 mV 2,3 0 300 Output noise voltage VONVIN= 20 V, IO= 5 mA, 2/ 10 Hz 100 kHz, TA= +25C 1 01 0 1000 V rms Output impedance ROVIN= 20 V, 2/ IO= 100 mA dc and 20 mA ac, fO= 120 Hz
43、1,2,3 01 1 Short circuit current IOSVIN= 20 V 1 01 1.6 A 2,3 1.3 Ripple rejection RRVIN= 20 V, 1 V rms, 4 01 48 dB f = 1 kHz, IO= 5 mA 5,6 42 1/ The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative current shall be defined as conventional c
44、urrent flow out of a device terminal. 2/ If not tested, shall be guaranteed to limits specified in table I herein. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90885 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS
45、, OHIO 43218-3990 REVISION LEVEL G SHEET 7 DSCC FORM 2234 APR 97 Case outline M Symbol Inches Millimeters Min Max Min Max A .190 .210 4.83 5.33 b - .030 - 0.76 D .410 .430 10.41 10.92 D1 .580 .610 14.73 15.49 e - .100 - 2.54 e1 - .200 - 5.08 E .410 .420 10.41 10.67 L1 .090 .110 2.29 2.79 L .115 .125
46、 2.92 3.18 N 3 3 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FI
47、GURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90885 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 8 DSCC FORM 2234 APR 97 Case outline U Letter Inches
48、 Millimeters Min Max Min Max A .190 .200 4.83 5.08 A1 .035 .045 0.89 1.14 A2 .120 BSC 3.05 BSC D .645 .665 16.38 16.89 D1 .410 .430 10.41 10.92 D3 .000 .065 0.00 1.65 e .100 BSC 2.54 BSC E .410 .422 10.41 10.71 L .500 .750 12.70 19.05 O .527 .537 13.39 16.64 P .140 .150 3.56 3.81 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, since this item was originally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units, th
