1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Make changes to 1.3 and ICCtest in table I. In accordance with N.O.R. 5962-R132-93. 93-05-05 M. A. FRYE B Make changes to VOUTand CINtests in table I. In accordance with N.O.R. 5962-R141-94. 94-03-31 M. A. FRYE C Make change to CMRR test in table
2、 I. In accordance with N.O.R. 5962-R026-95. 94-10-28 M. A. FRYE D Make change final electrical parameters in table II. In accordance with N.O.R. 5962-R192-95. 95-08-25 M. A. FRYE E Make changes to +IIN, -IIN, VIO, ICC, PSRR, CMRR, SSBW, GFPL, GFPH, GFR, HD2, HD3, and SR tests in table I. Redrawn. 96
3、-11-13 R. MONNIN F Drawing updated to reflect current requirements. - ro 03-02-20 R. MONNIN THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV F F F F F F SHEET 15 16 17 18 19 20 REV STATUS REV F F F F F F F F F F F F F F OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/
4、A PREPARED BY RICK C. OFFICER DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY CHARLES E. BESORE COLUMBUS, OHIO 43216 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, OPERATIONAL AMPLIFIER, HIGH SPEED
5、, PROGRAMMABLE AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 91-11-04 SUPPLY CURRENT, MONOLITHIC SILICON AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 5962-90993 SHEET 1 OF 20 DSCC FORM 2233 APR 97 5962-E193-03 DISTRIBUTION STATEMENT A. Approved for public release; distribution
6、is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90993 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing docu
7、ments two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness
8、 Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 90993 01 M P X Federal stock class designator RHA designator (see 1.2.1) Devicetype (see 1.2.2) Device class designator Caseoutline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Draw
9、ing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA
10、 designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 CLC505 High-speed programmable supply current operational amplifier 1.2.3 Device class designator. The device class de
11、signator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certificat
12、ion and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535
13、for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90993 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL F SHEE
14、T 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VS) . 7 V dc Output current (IOUT) . 70 mA Common mode input voltage (VCM) 7 V dc Differential input voltage (VID) . 10 V dc Power dissipation (PD) . 1.2 W Junction temperature (TJ) +175C Storage temperature range -65C to +15
15、0C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-ambient (JA) 100C/W Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage (VS) . 5 V dc Gain range (AV) . +2 to +21 and -1 to -20 Ambient operating temperatur
16、e range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in
17、 the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - T
18、est Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, sta
19、ndards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes preced
20、ence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect rel
21、iability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90993 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL F SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. T
22、he individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The i
23、ndividual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535
24、and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characte
25、ristics and post irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post irradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The elec
26、trical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked as listed in MIL-HDBK-103. For packages
27、 where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with
28、MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as requi
29、red in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance s
30、hall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for d
31、evice classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-3
32、8535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change as defin
33、ed in MIL-PRF-38535, appendix A. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at t
34、he option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
35、-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90993 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL F SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type L
36、imits Unit Min Max Input bias current (noninverting) +IINICC= 9 mA, 2/ 1,2 01 -18 +18 A RP= 33 k, RL= 250 3 -36 +36 ICC= 3.4 mA, 1,2 -6 +6 RP= 100 k, RL= 500 3 -12 +12 ICC= 1 mA, 2/ 1 -2.5 +2.5 RP= 300 k, RL= 1 k 2 -3.0 +3.0 3 -5 +5 Input bias current (inverting) -IINICC= 9 mA, 2/ 1 01 -38 +38 A RP=
37、 33 k, RL= 250 2 -40 +40 3 -60 +60 ICC= 3.4 mA, 1 -14 +14 RP= 100 k, RL= 500 2 -15 +15 3 -22 +22 ICC= 1 mA, 2/ 1 -7 +7 RP= 300 k, RL= 1 k 2 -11 +11 3 -10 +10 Input offset voltage VIOICC= 9 mA, 2/ 1 01 -8.0 +8.0 mV RP= 33 k, RL= 250 , 2 -14.0 +14.0 RS= 50 3 -12.8 +12.8 See footnotes at end of table.
38、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-90993 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Co
39、ntinued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Input offset voltage VIOICC= 3.4 mA, 1 01 -7.0 +7.0 mV RP= 100 k, RL= 500 , 2 -13.0 +13.0 RS= 50 3 -12.8 +12.8 ICC= 1 mA, 2/ 1 -7.0 +7.0 RP= 300 k, RL= 1 k, 2 -14.5 +14.5 RS=
40、 50 3 -13.0 +13.0 Average +input bias 2/ current drift TC(+IIN) ICC= 9 mA, 2 01 -100 +100 nA/C RP= 33 k, RL= 250 3 -225 +225 ICC= 3.4 mA, 2 -50 +50 RP= 100 k, RL= 500 3 -75 +75 ICC= 1 mA, 2 -30 +30 RP= 300 k, RL= 1 k, 3 -32 +32 Average -input bias 2/ current drift TC(-IIN) ICC= 9 mA, 2 01 -125 +125
41、nA/C RP= 33 k, RL= 250 3 -275 +275 ICC= 3.4 mA, 2 -60 +60 RP= 100 k, RL= 500 3 -100 +100 ICC= 1 mA, 2 -35 +35 RP= 300 k, RL= 1 k 3 -38 +38 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SI
42、ZE A 5962-90993 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL F SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Aver
43、age offset voltage 2/ drift TC(VIO) ICC= 9 mA, RP= 33 k, RL= 250 2,3 01 -50 +50 V/C ICC= 3.4 mA, RP= 100 k, RL= 500 -60 +60 ICC= 1 mA, RP= 300 k, RL= 1 k -75 +75 Supply current ICCRP= 33 k, no load 2/ 1,3 01 11 mA 2 12 RP= 100 k, no load 1,3 3.8 2 4.2 RP= 300 k, no load 2/ 1 1.3 2,3 1.4 Power supply
44、 rejection 3/ ratio PSRR ICC= 9 mA, 2/ 1 01 48 dB RP= 33 k, RL= 250 2,3 45 ICC= 3.4 mA, 1 48 RP= 100 k, RL= 500 2,3 45 ICC= 1 mA, 2/ 1 48 RP= 300 k, RL= 1 k 2,3 45 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR
45、D MICROCIRCUIT DRAWING SIZE A 5962-90993 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL F SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type
46、 Limits Unit Min Max Common mode 2/ rejection ratio CMRR ICC= 9 mA, VCM= 1 V, 4 01 48 dB RP= 33 k, RL= 250 5,6 45 ICC= 3.4 mA, VCM= 1 V, 4 48 RP= 100 k, RL= 500 5,6 45 ICC= 1 mA, VCM= 1 V, 4 48 RP= 300 k, RL= 1 k 5,6 45 Input resistance 2/ +RINICC= 9 mA, 1 01 800 k RP= 33 k, RL= 250 2 1600 3 400 ICC
47、= 3.4 mA, 1 2 M RP= 100 k, RL= 500 2 4 3 1 ICC= 1 mA, 1 5 RP= 300 k, RL= 1 k 2 10 3 2.5 Output impedance 2/ at dc ROUTICC= 9 mA, 1 01 0.3 RP= 33 k, RL= 250 2 0.2 3 1.2 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STA
48、NDARD MICROCIRCUIT DRAWING SIZE A 5962-90993 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL F SHEET 9 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output impedance 2/ at dc ROUTICC= 3.4 mA, 1 01 0.5 RP= 100 k, RL= 500 2 0.2 3 1.6 I
