1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add descriptive designator CQCC1-N20 for case outline 2. Add JAlimit of 95C/W for case outline 2. Changes in accordance with NOR 5962-R240-94. 94-08-10 M. A. FRYE B Update boilerplate paragraphs to current MIL-PRF-38535 requirements. Redrawn. - r
2、o 10-05-04 C. SAFFLE REV SHET REV B B B SHEET 15 16 17 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY MARCIA B. KELLEHER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THI
3、S DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, CMOS, HIGH PERFORMANCE DUAL SWITCHED CAPACITOR FILTER, MONOLITHIC SILICON DRAWING APPROVAL DATE 92-11-18 AMSC N/A REVISION LEVEL
4、B SIZE A CAGE CODE 67268 5962-91533 SHEET 1 OF 17 DSCC FORM 2233 APR 97 5962-E304-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91533 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEV
5、EL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or
6、Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91533 01 M R A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designat
7、orCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, a
8、ppendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 LMF100 High performance dual switched capacitor
9、filter 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in ac
10、cordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line 2 CQCC1-
11、N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT
12、DRAWING SIZE A 5962-91533 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ Supply voltage (V+ - V-) 16.0 V dc Voltage at any pin . V+ + 0.3 V, V- - 0.3 V Input current at any pin . 5 mA Package input current .
13、 20 mA Power dissipation (PD) 500 mW Junction temperature (TJ) . +150C Lead temperature (soldering, 10 seconds) +300C Storage temperature range . -65C to +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) : Case R 95C/W Case 2 . 71C/W 1.4
14、Recommended operating conditions. 2/ Supply voltage range 5 V (V+ - V-) 10 V Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to t
15、he extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test
16、 Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist
17、.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence.
18、Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliabili
19、ty. 2/ When the input voltage (VIN) at any pin exceeds the power supply rails (VIN V- or VIN V+), the absolute value of current at that pin should be limited to 5 mA or less. The sum of all currents at all pins that are driven beyond the power supply voltages should not exceed 20 mA. Provided by IHS
20、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91533 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requir
21、ements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requiremen
22、ts for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device cla
23、sses Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Block diagram. The block diagram shall be as specified
24、 on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature ra
25、nge. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be
26、 marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall b
27、e in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M sh
28、all be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certif
29、icate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers
30、 product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device
31、 class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required fo
32、r any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onsho
33、re at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 115 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
34、 IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91533 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions Q = 10, Mode = 1, R2= 10 k, R1= R3= 100 k, see figure 3, Group A su
35、bgroups Device type Limits 1/ Unit -55C TA+125C unless otherwise specified Min Max Supply current +ISfCLK= 250 kHz, no input signal, V+ = +5 V, V- = -5 V, ratio 100:1 1,2,3 01 13 mA fCLK= 250 kHz, no input signal, V+ = +5 V, V- = -5 V, ratio 50:1 13 fCLK= 250 kHz, no input signal, V+ = +2.5 V, V- =
36、-2.5 V, ratio 100:1 12 fCLK= 250 kHz, no input signal, V+ = +2.5 V, V- = -2.5 V, ratio 50:1 12 -ISfCLK= 250 kHz, no input signal, V+ = +5 V, V- = -5 V, ratio 100:1 -13 fCLK= 250 kHz, no input signal, V+ = +5 V, V- = -5 V, ratio 50:1 -13 fCLK= 250 kHz, no input signal, V+ = +2.5 V, V- = -2.5 V, ratio
37、 100:1 -12 fCLK= 250 kHz, no input signal, V+ = +2.5 V, V- = -2.5 V, ratio 50:1 -12 Output voltage swing +VOUTRL= 5 k for all outputs, V+ = +5 V, V- = -5 V 1,2,3 01 +3.7 V RL= 5 k for all outputs, V+ = +2.5 V, V- = -2.5 V +1.4 -VOUTRL= 5 k for all outputs, V+ = +5 V, V- = -5 V -3.7 RL= 5 k for all o
38、utputs, V+ = +2.5 V, V- = -2.5 V -1.4 See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91533 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC
39、 FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions Q = 10, Mode = 1, R2= 10 k, R1= R3= 100 k, see figure 3, Group A subgroupsDevice type Limits 1/ Unit -55C TA+125C unless otherwise specified Min Max DC offset voltage, see figure 4 VOS1fCLK= 250 kHz,
40、SA/B= V+, ratio 100:1, V+ = +5 V, V- = -5 V 1,2,3 01 -15 15 mV fCLK= 250 kHz, SA/B= V+, ratio 100:1, V+ = +2.5 V, V- = -2.5 V -15 15 fCLK= 250 kHz, SA/B= V+, ratio 50:1, V+ = +5 V, V- = -5 V -15 15 fCLK= 250 kHz, SA/B= V+, ratio 50:1, V+ = +2.5 V, V- = -2.5 V -15 15 fCLK= 250 kHz, SA/B= V-, ratio 10
41、0:1, V+ = +5 V, V- = -5 V -15 15 fCLK= 250 kHz, SA/B= V-, ratio 100:1, V+ = +2.5 V, V- = -2.5 V -15 15 fCLK= 250 kHz, SA/B= V-, ratio 50:1, V+ = +5 V, V- = -5 V -15 15 fCLK= 250 kHz, SA/B= V-, ratio 50:1, V+ = +2.5 V, V- = -2.5 V -15 15 VOS2fCLK= 250 kHz, SA/B= V+, ratio 100:1, V+ = +5 V, V- = -5 V
42、1,2,3 01 -80 80 fCLK= 250 kHz, SA/B= V+, ratio 100:1, V+ = +2.5 V, V- = -2.5 V -60 60 fCLK= 250 kHz, SA/B= V+, ratio 50:1, V+ = +5 V, V- = -5 V -80 80 fCLK= 250 kHz, SA/B= V+, ratio 50:1, V+ = +2.5 V, V- = -2.5 V -60 60 fCLK= 250 kHz, SA/B= V-, ratio 100:1, V+ = +5 V, V- = -5 V -70 70 fCLK= 250 kHz,
43、 SA/B= V-, ratio 100:1, V+ = +2.5 V, V- = -2.5 V -60 60 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91533 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION L
44、EVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions Q = 10, Mode = 1, R2= 10 k, R1= R3= 100 k, see figure 3, Group A subgroupsDevice type Limits 1/ Unit -55C TA+125C unless otherwise specified Min Max DC offset voltage - continued, V
45、OS2fCLK= 250 kHz, SA/B= V-, ratio 50:1, V+ = +5 V, V- = -5 V 1,2,3 01 -70 70 mV see figure 4 fCLK= 250 kHz, SA/B= V-, ratio 50:1, V+ = +2.5 V, V- = -2.5 V -60 60 VOS3fCLK= 250 kHz, SA/B= V+, ratio 100:1, V+ = +5 V, V- = -5 V 1,2,3 01 -60 60 fCLK= 250 kHz, SA/B= V+, ratio 100:1, V+ = +2.5 V, V- = -2.
46、5 V -30 30 fCLK= 250 kHz, SA/B= V+, ratio 50:1, V+ = +5 V, V- = -5 V -60 60 fCLK= 250 kHz, SA/B= V+, ratio 50:1, V+ = +2.5 V, V- = -2.5 V -30 30 fCLK= 250 kHz, SA/B= V-, ratio 100:1, V+ = +5 V, V- = -5 V -60 60 fCLK= 250 kHz, SA/B= V-, ratio 100:1, V+ = +2.5 V, V- = -2.5 V -30 30 fCLK= 250 kHz, SA/B
47、= V-, ratio 50:1, V+ = +5 V, V- = -5 V -60 60 fCLK= 250 kHz, SA/B= V-, ratio 50:1, V+ = +2.5 V, V- = -2.5 V -30 30 Clock to center frequency ratio deviation fCLK/fOV+ = +5 V, V- = -5 V, fCLK= 1 MHz, ratio 50:1, V50/100= 5 V or 0 V 1,2,3 01 -0.7 0.7 % V+ = +2.5 V, V- = -2.5 V, fCLK= 1 MHz, ratio 50:1
48、, V50/100= 5 V or 0 V -0.9 0.9 V+ = +5 V, V- = -5 V, fCLK= 1 MHz, ratio 100:1, V50/100= 5 V or 0 V -0.7 0.7 V+ = +2.5 V, V- = -2.5 V, fCLK= 1 MHz, ratio 100:1, V50/100= 5 V or 0 V -0.9 0.9 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91533 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Con
