1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to current requirements. Editorial changes throughout. - gap 10-05-04 Charles F. Saffle REV SHET REV SHET REV STATUS REV A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY Larry T. Gauder DEFENSE SUP
2、PLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Thomas M. Hess APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ECL, DIGITAL FIXED MODULUS
3、 DIVIDER, 3.3 GHz 8, MONOLITHIC SILICON DRAWING APPROVAL DATE 94-12-16 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-91570 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E058-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT
4、DRAWING SIZE A 5962-91570 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class
5、V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91570 01 M P X Federal
6、 stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked w
7、ith the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
8、Device type Generic number Circuit function 01 SP8808AC Digital, fixed modulus divider, 3.3 GHz 8 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certificati
9、on to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descr
10、iptive designator Terminals Package style P CDIP2-T8 or GDIP1-T8 8 Dual-in-line package 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted
11、 without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91570 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) . -0.0 V dc minimum to +6.5 V maximum Clock input voltage 2.5 Vp
12、p Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) +175C Maximum power dissipation (PD) 330 mW 2/ Thermal resistance, junction-to-case (JC) See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage range (VCC) . +4.75 V dc
13、 minimum to +5.25 V dc maximum Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specif
14、ied, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Inte
15、rface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardizat
16、ion Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes appli
17、cable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Maximum power dissipation without additional
18、 heatsinking.- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91570 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requiremen
19、ts. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein.
20、The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-3
21、8535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Functional diagram. The
22、functional diagram shall be as specified on figure 2. 3.2.4 Test circuit and timing diagram. The test circuit and timing diagram shall be as specified on figure 3. 3.2.5 Input sensitivity. The input sensitivity shall be as specified on figure 4. 3.2.6 Inner-layer dielectric. Polyimide and silicon co
23、atings are allowed as part of the wafer fabrication process provided that each micrcircuit inspection lot (see MIL-PRF-38535, “Inspection lot - class B“) shall be subjected to and pass the internal water vapor content test in accordance with group D6 of test method 5005 of MIL-STD-883. The frequency
24、 of the internal water vapor testing may not be decreased unless approved by the preparing activity. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are
25、 as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be mark
26、ed with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option,
27、the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a
28、“QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply
29、to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing
30、as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate
31、of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change o
32、f product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and app
33、licable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 33 (see MIL-PRF-38535, appendix A). Provid
34、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91570 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Sy
35、mbol Conditions 1/ -55C TC +125C 4.75 V VCC 5.25 V unless otherwise specified Group A subgroups Limits Unit Min Max Power supply current ICCVCC= 4.75 V to 5.25 V 2/ ECL 1, 2, 3 85 mA Output voltage swing VOSVCC= 4.75 V to 5.25 V, FIN= 100 MHz, See figure 3 ECL 1, 2, 3 450 mVp-pFunctional tests See 4
36、.4.1b 2/ 7, 8 Operating frequency range fMAXVCC= 4.75 V to 5.25 V, VIN= 175 - 400 mVrms, 650 MHz, VIN= 600 mVrms, 2000 MHz, VIN= 1750 mVrms, 2800 MHz, VIN= 400 - 600 mVrms, 3.3 GHz 9, 10, 11 650 3300 MHz Propagation delay, clock to output tPHLVCC= 5.0 V, RLOAD= 470 3/ 9, 10, 11 6 ns Propagation dela
37、y, clock to output tPLHVCC= 5.0 V, RLOAD= 470 3/ 9, 10, 11 6 ns 1/ All tests must be performed under the worst case conditions. 2/ This test is carried out in conjunction with switching tests (subgroups 9, 10, and 11) and is sufficient to verify the function of the device. 3/ These parameters are gu
38、aranteed, if not tested, to the limits specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91570 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2
39、234 APR 97 Case outline P Terminal number Terminal symbol 1 VCC2 INPUT3 INPUT$ $ $ $ $ $ $ $ $4 NC5 GND 6 OUTPUT$ $ $ $ $ $ $ $ $ $ $ $ $7 OUTPUT8 NC NC = No connection FIGURE 1. Terminal connections. FIGURE 2. Functional diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted
40、without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91570 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 FIGURE 3. Test circuit and timing diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without
41、 license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91570 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 FIGURE 4. Input sensitivity. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,
42、-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91570 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-385
43、35 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Screening. Fo
44、r device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devic
45、es prior to quality conformance inspection. 4.2.1 Additional criteria for device class M. a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the p
46、reparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as sp
47、ecified in table II herein. 4.2.2 Additional criteria for device classes Q and V. a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device manufacturers QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be
48、maintained under document revision level control of the device manufacturers Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein. c. Additional screening for dev
