1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Table I, add new note 1 to table and settling time to 0.1% test. 99-11-29 Raymond Monnin B Update drawing boilerplate. 04-08-23 Raymond Monnin C Paragraph 1.3, thermal resistance, junction-to-case, change 55 C/W to 75 C/W. Table I: Input offset v
2、oltage maximum limit, change 2 mV to 5 mV. Input offset voltage temperature coefficient maximum limit, change 25 mV/ C to 50 mV/ C. Input offset current, subgroup 1 maximum limit, change 250 pA to 500 pA. 05-10-05 Raymond Monnin D Added footnote 1 to table II, under group C end-point electricals. Up
3、dated drawing paragraphs. -sld 12-08-07 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Steve Duncan DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHE
4、CKED BY Michael Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, DIFFERENTIAL OPERATIONAL AMPLIFIER, FET INPUT DRAWING APPROVAL DATE 93-07-09 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE
5、67268 5962-91574 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E433-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91574 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234
6、APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness
7、assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 91574 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Dra
8、wing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function
9、 as follows: Device type Generic number Circuit function 01 MSK 801B FET input, differential operational amplifier 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534
10、 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standa
11、rd military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperatur
12、e range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. Th
13、ese exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers inter
14、nal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91574 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC
15、FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 12 TO-8 can 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratin
16、gs. 1/ Supply voltage (VCC) 18 V dc Supply voltage (VSC) 18 V dc Input voltage (VIN) VCCPeak output current (IOUT) 120 mA Total hybrid power dissipation (PD) 1.0 W Thermal resistance junction-to-case (qJC) 75 C/W (Output Qs) Storage temperature -65 C to +150 C Junction temperature (TJ) +175 C 1.4 Re
17、commended operating conditions. Supply voltage (VCC) 15 V dc Supply voltage (VSC) 15 V dc Case operating temperature range (TC). -55 C to +125 C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this d
18、rawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Me
19、thod Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assis
20、t.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Noth
21、ing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. P
22、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91574 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item p
23、erformance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device
24、 class. The manufacturer may eliminate, modify, or optimize the tests and inspections herein, however, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of th
25、e device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Te
26、rminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3
27、.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the
28、 PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial
29、 quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and
30、be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime
31、-VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sa
32、mpling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall
33、 be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA
34、 Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 o
35、f MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license
36、 from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91574 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55 C TC +125 C VCC= 15 V dc VSC= 15 V dc unless otherwise specified Gr
37、oup A subgroups Device type Limits Unit Min Max Quiescent current IQVIN= 0 V 1 01 30 mA 2,3 32 Input offset voltage VOSVIN= 0 V, TC= +25 C 1 01 5 mV Input offset voltage temperature coefficient DVOSDT VIN= 0 V, TC= -55 C and +125 C 2,3 01 50 mV/ C Input bias current IIBVCM= 0 V 1 01 500 pA 2,3 10 nA
38、 Input offset current IOSVCM= 0 V 1 01 500 pA 2,3 5 nA Output current IOUTRL= 100W, VO= 10 V4,5,6 3/ 01 100 mA Output voltage swing VORL= 100W, f 10 MHz 4,5,6 3/ 01 10 V Full power bandwidth FBW RL= 100W, VO= 10 V 4 01 10 MHz 5,6 3/ 8 Unity gain crossover mEW RL= 510W, VIN= 0.1 V 4 01 100 MHz 5,6 3/
39、 80 Slew rate limit SLR RL= 100W, VO= 10 V, f = 1 kHz 4 01 650 V/ms 5,6 3/ 450 Large signal voltage gain AVOLRL= 1 kW, VO= 10 V, f = 1 kHZ 4 01 50 dB 5,6 3/ 40 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MI
40、CROCIRCUIT DRAWING SIZE A 5962-91574 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics- Continued. Test Symbol Conditions -55 C TC +125 C VCC= 15 V dc VSC= 15 V dc unless otherwise specified Group A subgroup
41、s Device type Limits Unit Min Max Settling time to 0.1% 1/ tSRL= 100W, VO= 10 V step 4 01 75 ns 5,6 100 Settling time to 1.0% tS1RL= 100W, VO= 10 V step 4 01 55 ns 5,6 3/ 75 Power supply rejection ratio 1/ PSRR DVCC= 5 V 1 01 60 dB 2,3 2/ 40 Common mode rejection ratio 1/ CMRR DVIN= 10 V, f = 10 Hz4
42、,5,6 3/ 01 70 dB 1/ Parameter is guaranteed to the limits specified in table I by design and is not tested. 2/ Subgroups 2 and 3 for power supply rejection ratio (PSRR) shall be tested as part of device initial characterization and after design and process changes. Subgroups 2 and 3 for the paramete
43、r (PSRR) shall be guaranteed to the limits specified in table I for all lots not specifically tested. 3/ Subgroups 5 and 6 shall be tested as part of device initial characterization and after design and process changes. Subgroups 5 and 6 shall be guaranteed to the limits specified in table I for all
44、 lots not specifically tested. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91574 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Milli
45、meter Inches Min Max Min Max A 4.57 5.08 .180 .200 b 0.41 0.51 .016 .020 D 14.99 15.49 .590 .610 D1 13.97 REF .550 REF e 10.16 REF .400 REF e1 5.08 REF .200 REF e2 2.54 REF .100 REF F 0.56 0.76 .022 .030 k 0.66 0.91 .026 .036 k1 0.66 0.91 .026 .036 L 6.10 - .240 - Q - 1.14 - .045 a 45 BSC 45 BSC NOT
46、ES: 1. The U.S. government preferred system of measurement is the metric SI system. However, this item was originally designed using inch-pound units of measurement. In the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. 2. Pin numbers are for r
47、eference. FIGURE 1. Case outline(s). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91574 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case ou
48、tline X Terminal number Terminal symbol 1 2 3 4 5 6 7 8 9 10 11 12 +VCCOutput compensation Compensation balance Compensation balance -Input +Input No connection Case ground -VCC-VSC Output +VSC FIGURE 2. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91574 DLA LAND AND MARITIME
