1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change min. limits for tPLH2, tPHL2, tTLH, and tTHLon table 1. Update drawing format to latest boilerplate. Editorial changes throughout. les 99-06-25 Raymond Monnin B Update to current requirements. Editorial changes throughout. - gap 06-10-02 R
2、aymond Monnin THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Thanh V. Nguyen DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Tim H. Noh COLUMBU
3、S, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ECL, DUAL 8-INPUT AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 92-05-04 MULTIPLEXER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SI
4、ZE A CAGE CODE 67268 5962-91655 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E521-06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91655 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B
5、 SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Iden
6、tifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91655 01 M X X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorC
7、ase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, app
8、endix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 100363 Dual 8-input multiplexer 1.2.3 Device class
9、 designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-385
10、35, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDIP5-T24 or CDIP6-T24 24 Dual-in-line package Y See figure 1 24 Quad-fl
11、at package 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91655
12、 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Negative supply voltage range (VEE) . -7.0 V dc to +0.5 V dc DC input voltage range (VIN) . VEEto +0.5 V dc Maximum dc output current (IOUT) . -50 mA Storage temp
13、erature range . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) +175C Maximum power dissipation (PD) . 580 mW Thermal resistance, junction-to-case (JC): Case X See MIL-STD-1835 Case Y 28C/W 1.4 Recommended operating conditions. Negative supply voltage range (VE
14、E) . -5.7 V dc minimum to -4.2 V dc maximum High level input voltage range (VIH) -1.165 V dc minimum to -0.870 V dc maximum Low level input voltage range (VIL) -1.830 V dc minimum to -1.475 V dc maximum Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specif
15、ication, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-
16、38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit
17、Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of prece
18、dence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute
19、 maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91655 DEFENSE
20、 SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufactu
21、rers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2
22、 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance
23、 with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3. 3.2.4 Test circuit and switching waveforms. Test circuit and switching waveforms shall be as specified
24、on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range.
25、 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be mar
26、ked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in
27、 accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall
28、be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificat
29、e of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers pro
30、duct meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device cla
31、ss M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for an
32、y change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore a
33、t the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 32 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,
34、-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91655 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C 1/ -5.7 V VEE -4.2 V Group A subgroups Limits Unit Unless o
35、therwise specified Min Max 1, 2 -1025 -870 High level output voltage VOH VEE= -4.2 V, VIL= -1.83 V, VIH= -0.87 V 3 -1085 -870 mV 1, 2 -1830 -1620 Low level output voltage VOL 3 -1830 -1555 mV 1, 2 -1035 High level threshold output voltage VOHC VEE= -4.2 V, VIL= -1.475 V, VIH= -1.165 V 3 -1085 mV 1,
36、2 -1610 Low level threshold output voltage VOLC 3 -1555 mV 1, 2 265 High level input current, select inputs IIH1 VEE= -5.7 V, VIN= -0.87 V3 385 1, 2 340 High level input current, IIH2 3 490 A Low level input current IILVEE= -4.2 V, VIN= -1.83 V 1, 2, 3 0.5 Power supply drain current IEEVEE= -5.7 V,
37、-4.2 V Inputs open 1, 2, 3 -87 -30 mA Functional tests VEE= -5.7 V, -4.2 V, VIH= -1018 mV, VIL= -1652 mV See 4.4.1b 7, 8A, 8B 9 0.6 2.3 10 0.7 3.0 Propagation delay time, data to output tPLH1, tPHL111 0.5 2.4 9 0.9 2.8 10 0.8 3.4 Propagation delay time, data to output tPLH2, tPHL211 0.8 3.0 9 0.3 1.
38、8 10 0.3 2.1 Transition time, output 2/ tTLH, tTHLSee figure 4. 11 0.3 1.9 ns 1/ Each input/output, as applicable, shall be tested at the specified temperature for the specified limits. Output terminals shall be terminated through 50 to -2.0 V. Input terminals not designated shall be high logic leve
39、l, low logic level or open. 2/ This parameter is provided as design information only (not tested but guaranteed). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91655 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS,
40、 OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 Case Y Millimeters Inches Dimension Min Max Min Max Notes A 2.16 .085 b 0.41 0.46 .016 .018 c 0.10 0.15 .004 .006 D 22.10 28.45 .870 1.120 D1 9.4 10.16 .370 .400 4 E 22.10 28.45 .870 1.120 E1 9.40 10.16 .370 .400 4 e 1.14 1.40 .045 .055
41、 L 6.35 9.14 .250 .360 Q 0.89 1.27 .035 .050 5 S 1.91 .075 NOTES: 1. The preferred unit of measurement is millimeters. However, this item was designed using inch-pound units of measurement. In case problems involving conflicts between the metric and inch-pound units, the inch-pound units shall rule.
42、 2. Lead number 1 is identified by a tab located on the lead. 3. Lead numbers are shown for reference only and do not appear on the package. 4. Dimensions D1 and E1 allow glass meniscus. 5. Dimension Q shall be measured at the point of exit of the lead from the body. FIGURE 1. Case outline. Provided
43、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91655 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 Device Type 01 01 Case outline X Y Terminal Connection Ter
44、minal symbol Terminal Symbol 1 B3 B6 2 B2 B5 3 B1 B4 4 B0 B3 5 Zb B2 6 VCC B1 7 VCCA B0 8 Za Zb 9 A0 VCC 10 A1 VCCA 11 A2 Za 12 A3 A0 13 A4 A1 14 A5 A2 15 A6 A3 16 A7 A4 17 S0 A5 18 VEE A6 19 S1 A7 20 S2 S0 21 B7 VEE 22 B6 S1 23 B5 S2 24 B4 B7 FIGURE 2. Terminal connections. Provided by IHSNot for R
45、esaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91655 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 Inputs Outputs S2 S1 S0 A7B7 A6B6 A5B5 A4B4 A3B3 A2B2 A1B1 A0B0 Za Zb L L
46、L X X X X X X X L L L L L X X X X X X X H H L L H X X X X X X L X L L L H X X X X X X H X H L H L X X X X X L X X L L H L X X X X X H X X H L H H X X X X L X X X L L H H X X X X H X X X H H L L X X X L X X X X L H L L X X X H X X X X H H L H X X L X X X X X L H L H X X H X X X X X H H H L X L X X X
47、X X X L H H L X H X X X X X X H H H H L X X X X X X X L H H H H X X X X X X X H H = High voltage level L = Low voltage level X = Irrelevant FIGURE 3. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 59
48、62-91655 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 NOTES: 1. VCC= VCCA= +2.0 V, VEE= -2.5 V. 2. L1 and L2 = equal length 50 impedance lines. 3. RT=50 terminator internal to scope. 4. Decoupling 0.1 F from GND to VCCand VEE. 5. All unused outputs are loaded with 50 to GND. 6. CL= fixture and stray capacitance 3 pF. FIGURE 4. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
