1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to current requirements. Editorial changes throughout. - gap 10-03-18 Charles F. Saffle REV SHET REV SHET REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Thanh V. Ngu
2、yen DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Thanh V. Nguyen APPROVED BY Joseph A. Dupay MICROCIRCUIT, DIGITAL, BIPOLAR, LOW-
3、POWER SCHOTTKY TTL, QUADRUPLE TRIDIRECTIONAL BUS TRANSCEIVER, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-07-02 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-91661 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E511-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without li
4、cense from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91661 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q an
5、d M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the followi
6、ng example: 5962 - 91661 01 M R X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38
7、535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) i
8、dentify the circuit function as follows: Device type Generic number Circuit function 01 54LS442 Quadruple tridirectional bus transceiver 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements
9、documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-18
10、35 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line package S GDFP2-F20 or CDFP3-F20 20 Flat package 2 CQCC1-N20 20 Leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and
11、 V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91661 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 9
12、7 1.3 Absolute maximum ratings. 1/ Supply voltage range -0.5 V dc minimum to +7.0 V dc maximum Input voltage range . -1.5 V dc at -18 mA to +7.0 V dc Off-state output voltage . +5.5 V dc maximum Storage temperature range . -65C to +150C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junc
13、tion temperature (TJ) +175C Lead temperature (soldering, 10 seconds) +300C Maximum power dissipation (PD) 2/ . 522.5 mW 1.4 Recommended operating conditions. Supply voltage range (VCC) . +4.5 V dc minimum to +5.5 V dc maximum Minimum high level input voltage (VIH) 2.0 V dc Maximum low level input vo
14、ltage (VIL) . 0.5 V dc Maximum input clamp current (IIK) . -18 mA Maximum high level output current (IOH) . -12 mA Maximum low level output current (IOL) . 12 mA Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The fo
15、llowing specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturin
16、g, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microci
17、rcuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this draw
18、ing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Exten
19、ded operation at the maximum levels may degrade performance and affect reliability. 2/ Power dissipation is defined as VCCx ICCand must withstand the added PDdue to short circuit test; e.g., IOS. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDA
20、RD MICROCIRCUIT DRAWING SIZE A 5962-91661 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specif
21、ied herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN c
22、lass level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outli
23、nes. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2
24、.5 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation para
25、meter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The pa
26、rt shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product usi
27、ng this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q a
28、nd V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in
29、order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA p
30、rior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance
31、. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSC
32、C-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers
33、facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 9 (see MIL-PRF-38535, appe
34、ndix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91661 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance character
35、istics. Test SymbolConditions -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Group A Subgroups Limits Unit Min Max High level output voltage VOHVCC= 4.5 V, VIL= 0.5 V, VIH= 2.0 V IOH= -3.0 mA 1, 2, 3 2.4 V OH= -12.0 mA 1, 2, 3 2.0 Low level output voltage VOLIOL= 12 mA 1, 2, 3 0.4 Input
36、clamp voltage VIKVCC= 4.5 V, IIN= -18 mA 1, 2, 3 -1.5 Hysteresis (VT+- VT-) 1/ VTVCC= 4.5 V A, B, C inputs 1, 2, 3 0.1 High level input current IIH1VCC= 5.5 V, VIN= 2.7 V 1, 2, 3 20 A IIH2VCC= 5.5 V, VIN= 5.5 V A, B, C inputs 1, 2, 3 100 IH3VCC= 5.5 V, VIN= 7.0 V Other inputs 1, 2, 3 100 Low level i
37、nput current IILVCC= 5.5 V, VIN= 0.4 V 1, 2, 3 -0.4 mA Off-state output current, high level voltage applied IOZHVCC= 5.5 V, CS$ $ $ $at 2.0 V VOUT= 2.7 V 1, 2, 3 20 A Off-state output current, low level voltage applied IOZLVOUT= 0.4 V 1, 2, 3 -400 Short-circuit output current 2/ IOSVCC= 5.5 V, VOUT=
38、 0.0 V 1, 2, 3 -40 -225 mA Supply current ICCVCC= 5.5 V Outputs open Outputs low 1, 2, 3 90 mA Outputs at high Z 1, 2, 3 95 Functional tests See 4.4.1b, VCC= 4.5 V, 5.5 V 7, 8 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS
39、-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91661 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test SymbolConditions -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified G
40、roup A Subgroups Limits Unit Min Max Propagation delay time, A to B or C, B to A or C, and C to A or B tPLHCL= 45 pF, RL= 667 , See figure 4 9 14 ns 10, 11 20 tPHL9 20 10, 11 28 Output enable time to low level Any G%to A, B, C tPZL9 33 10, 11 46 S0, S1 to A, B, C 9 42 10, 11 59 CS$ $ $ $to A, B, C 9
41、 36 10, 11 50 Output enable time to high level, G%, S, CS$ $ $ $to A, B, C tPZH9 32 10, 11 45 Output disable time from low level, G%, S, CS$ $ $ $to A, B, C tPLZCL= 5 pF, RL= 667 , See figure 4 9 35 10, 11 49 Output disable time from high level, G%, S, CS$ $ $ $to A, B, C tPHZ9 25 10, 11 35 1/ Guara
42、nteed but not tested. 2/ Not more than one output should be shorted at a time and duration of the short-circuit should not exceed one second. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91661 DEFENSE SUPP
43、LY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outlines R, S, and 2 Terminal number Terminal symbol 1 CS$ $ $ $2 B1 3 C1 4 C25 B2 6 B3 7 C3 8 C49 B4 10 GND 11 S0 12 S1 13 A4 14 A3 15 A2 16 A1 17 G%A 18 G%B 19 G%C 20 VCCFIGURE 1. Termin
44、al connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91661 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 Inputs Transfers between buses CS$
45、 $ $ $S1 S0 G%A G%B G%C H X X X X X None X H H X X X None X X X H H H None X L L X H H None X L H H X H None X H L H H X None L L L X L L A B, A C L L H L X L B C, B A L H L L L X C A, C B L L L X L H A B L L H H X L B C L H L L H X C A L L L X H L A C L L H L X H B A L H L H L X C B H = High level
46、voltage L = Low level voltage X = Irrelevant FIGURE 2. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91661 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC
47、 FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91661 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 10 DSCC FORM 2234 APR 97 FIGURE
48、 4. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91661 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 11 DSCC FORM 2234 APR 97 NOTES: 1. RL= Load resistor; see table I for value. 2. CL= Load capacitance includes jig and probe capacitance; see table I for value. 3. All di
