1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing being updated to reflect current requirements. - ro 00-10-23 R. MONNIN B Add device type 02 and case outline Y. Make changes to JCand JAlimits as specified under paragraph 1.3. Add supply voltage limit for device type 02 and PU, PD limits
2、 under paragraph 1.4. Make changes to Table I and figure 1. Add Table IIB. - ro 11-09-29 C. SAFFLE REV SHEET REV B SHEET 15 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY MARCIA B. KELLEHER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3
3、990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY CHARLES E. BESORE APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, BRUSHLESS DC MOTOR CONTROLLER, MONOLITHIC SILICON DRAWING
4、APPROVAL DATE 93-07-07 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-91689 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E191-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91689 DLA LAND AND MARITIME
5、COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are avail
6、able and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 91689 02 V Y A Federal stock class designator RHA designator (see 1.2.1) Device
7、 type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA
8、 marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 UC1625
9、Brushless DC motor controller 02 UC1625-SP Brushless DC motor controller 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements fo
10、r MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Termina
11、ls Package style X GDIP1-T28 or CDIP2-T28 28 Dual-in-line Y GDIP4-T28 28 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted w
12、ithout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91689 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ VCCsupply voltage (VCC) . +20 V Power VCCsupply voltage (POWER-VCC) . +20 V PWM IN voltage 0.
13、3 V to 6 V E/A IN+, E/A IN- voltage . -0.3 V to 12 V ISENSE1, ISENSE2 voltage . -1.3 V to 6 V OV-COAST, DIR, SPEED-IN, H1, H2, H3 voltage: Device type 01 . -0.3 V to 8 V OV-COAST, DIR, SPEED-IN, SSTART, QUAD SEL voltage: Device type 02 . -0.3 V to 8 V H1, H2, H3 voltage: Device type 02 . -0.3 V to 1
14、2 V S START, QUAD SEL voltage : Device type 01 . -0.3 V to 8 V PU output voltage . -0.3 V to 50 V PU output current +200 mA continuous PD output current : Device type 01 . +200 mA continuous Device type 02 . 200 mA continuous E/A OUT output current 10 mA I-SENSE output current -10 mA TACH-OUT output
15、 current 10 mA VREFoutput current -50 mA continuous Power dissipation (PD), TA= +25C . 1.9 W 3/ Junction temperature (TJ) . +150C Storage temperature range . 65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) : Case outline X . 16C/W Case outline Y
16、. 4.95C/W Thermal resistance, junction-to-ambient (JA) : Case outline X . 65C/W Case outline Y . 43.1C/W 1.4 Recommended operating conditions. Supply voltage range : Device type 01 . 0.3 V dc to 12 V dc Device type 02 . 10 V dc to 18 V dc PU output current +85 mA continuous PD output current: Device
17、 type 01 . 85 mA continuous Device type 02 . 85 mA continuous Fall time (high side drivers) 10% to 90% slew time, 50 mA load : Device type 02 only . 500 ns Ambient operating temperature range (TA) . -55C to +125C _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the devic
18、e. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Currents are positive into and negative out of the specified terminal. 3/ Derate at 15 mW/C for TA 25C Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN
19、DARD MICROCIRCUIT DRAWING SIZE A 5962-91689 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing
20、 to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 -
21、 Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/a
22、ssist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precede
23、nce. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as
24、 modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B dev
25、ices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case out
26、line shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Block diagram. The block diagram shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless oth
27、erwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified
28、in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN is not feasible due to space limitations, the
29、manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appen
30、dix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networki
31、ng permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91689 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML
32、-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of com
33、pliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, append
34、ix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device c
35、lass M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA
36、Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class
37、 M devices covered by this drawing shall be in microcircuit group number 55 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91689 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-39
38、90 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Supply current IS1,2,3 01,02 30.0 mA VCCturn-on threshold voltage VTHON1,2,3 01 8.65
39、 9.45 V 02 8.65 9.55 VCCturn-off threshold voltage VTHOFF1,2,3 01,02 7.75 8.55 V OVERVOLTAGE / COAST section OV-COAST inhibit threshold voltage VITH1,2,3 01,02 1.65 1.85 V OV-COAST restart threshold voltage VRTHTA= +25C 1 01,02 1.55 1.75 V OV-COAST hysteresis voltage VHYS TA= +25C 1 01 0.05 0.15 V 0
40、2 0.05 0.155 OV-COAST input current IINTA= +25C 1 01 -10 0 A 02 -10 10 LOGIC INPUTS section H1, H2, H3 low threshold voltage VLTH1,2,3 01,02 0.8 1.25 V H1, H2, H3 high threshold VHTH1,2,3 01,02 1.6 2.0 V H1, H2, H3 input current IINH1,2,3 01,02 -400 -120 A QUAD SEL, DIR threshold voltage VTH1,2,3 01
41、 0.8 2.0 V 02 0.8 3.0 QUAD SEL hysteresis voltage QSHYS1,2,3 01 130 mV 02 130 DIR hysteresis voltage DHYS1,2,3 01 0.4 0.8 V 02 0.4 0.9 QUAD SEL input current IINQS1,2,3 01,02 -30 150 A DIR input current IINDIR1,2,3 01,02 -30 30 A See footnotes at end of table. Provided by IHSNot for ResaleNo reprodu
42、ction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91689 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C
43、 unless otherwise specified Group A subgroups Device type Limits Unit Min Max PWM AMP/COMPARATOR section E/A IN+, E/A IN- input current IINE/ATo 2.5 V, TA= +25C 1 01,02 -5.0 5.0 A PWM IN input current IINPWMTo 2.5 V, TA= +25C 1 01,02 0 30 A Error amp input offset voltage VINOF0 V VCOMMON 3 V, TA= +2
44、5C 1 01,02 -10 10 mV Error amp voltage gain AVTA= +25C 1 01,02 70 dB E/A OUT voltage range VR1,3 01,02 0.25 3.50 V 2 02 0.25 4.20 S START pull-up current ISSPU1 01,02 -16 -5 A 2,3 02 -17.5 -5 S START discharge current ISSDTA= +25C 1 01 0.1 3.0 mA To 2.5 V, TA= +25C 02 0.1 3.0 S START restart thresho
45、ld voltage ISSRTA= +25C 1 01,02 0.1 0.3 V CURRENT AMP section Gain A/V ISENSE1 = 0.3 V, 1,2,3 01 0.1 3.0 V/V ISENSE2 = 0.5 V to 0.7 V 02 1.75 2.15 Level shift voltage VLSISENSE1 = 0.3 V, ISENSE2 = 0.3 V 1,2,3 01,02 2.4 2.65 V Peak current threshold voltage VPIISENSE1 = 0 V, force ISENSE2 1,2,3 01,02
46、 0.14 0.26 V Over current threshold voltage VOIISENSE1 = 0 V, force ISENSE2 1,2,3 01,02 0.26 0.36 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91689 DLA LAND AND MARITIME C
47、OLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max CURRENT AMP section continued. ISENSE1, ISENSE2 inpu
48、t current IIISTo 0 V 1,2,3 01,02 -850 0 A ISENSE1, ISENSE2 offset current IOFISTo 0 V 1,2,3 01,02 -12 +12 A ISENSE1, ISENSE2 voltage range VRIS1,2,3 01,02 -1 2 V TACHOMETER/BRAKE section TACH-OUT high level voltage VTOH10 k to 2.5 V 1,2,3 01,02 4.7 5.3 V TACH-OUT low level voltage VTOL10 k to 2.5 V 1,2,3 01,02 0.2 V On time tO2/ 9,10,11 01,02 170 280 s RC-BRAKE input current IIN1,2,3 01,02 -4.0 mA Threshold to brake, RC-BRAKE VTHB1,2,3 01,02 0.8 1.2 V Brake to hysteresis, RC-BRAKE VTHH 1 01 0.4 V 1,2,3 02 0.4 SPEED-
