1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R. 5962-R147-93. 93-05-06 M. A. FRYE B Changes in accordance with N.O.R. 5962-R237-93. 93-10-15 M. A. FRYE C Changes in accordance with N.O.R. 5962-R030-95. 94-11-09 M. A. FRYE D Make change to Feedthrough test as s
2、pecified under TABLE I. Redrawn. - ro 97-12-08 R. MONNIN E Replace reference to MIL-STD-973 with reference to MIL-PRF-38535. - ro 05-02-04 R. MONNIN THE ORIGINAL FIRST SHEET OF THIS DRAWING HAS BEEN REPLACED. REV SHET REV SHET REV STATUS REV E E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8
3、9 10 11 12 13 PMIC N/A PREPARED BY RICK C. OFFICER DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY CHARLES E. BESORE COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A. FRYE AND AGENCIES OF THE DEPARTMEN
4、T OF DEFENSE DRAWING APPROVAL DATE 92-06-24 MICROCIRCUIT, LINEAR, VOLTAGE CONTROLLED GAIN AMPLIFIER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-91694 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E061-05 Provided by IHSNot for ResaleNo reproduction or networking permitted wi
5、thout license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device clas
6、ses Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the
7、 following example: 5962 - 91694 01 M C X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the M
8、IL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device
9、type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 CLC520 Voltage controlled gain amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements
10、 documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1
11、835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line 2 CQCC1-N20 20 Square leadless chop carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for devic
12、e class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply
13、 voltage (V) . 7 V dc Output current (IOUT) 70 mA Common mode input voltage (VCM) V Differential input voltage 10 V Gain controlled input voltage (VG) V Reference input voltage (VREF) V Power dissipation (PD) 1.2 W Junction temperature (TJ) . +175C Storage temperature range . -65C to +150C Lead temp
14、erature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case C (side braze) . 70C/W Case C (cerdip) . 90C/W Case 2 . 55C/W 1.4 Recommended operating conditions. Supply voltage (V) . 5 V dc Gain range (AV) 2 to 1
15、00 Reference input voltage (VREF) 150 mW Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless o
16、therwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-
17、STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/a
18、ssist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing
19、in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Prov
20、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual
21、item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item
22、 requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for
23、 device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.3 Electrical performance characteristics and
24、postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test re
25、quirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN num
26、ber is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class
27、M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Ce
28、rtificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in
29、order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements
30、of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with
31、each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and
32、review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group ass
33、ignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91694 DEFEN
34、SE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min MaxStatic and dc characteristics Inp
35、ut bias current (noninverting) +IIN1,2 01 -28 +28 A 3 -61 +61 Input bias current (inverting) -IIN1,2 01 -28 +28 A 3 -61 +61 Output offset voltage VOO1 01 -120 +120 mV 2,3 -150 +150 Average +input bias current drift TC (+IIN) 3/ 2 01 -165 +165 nA/C 3 -415 +415 Average -input bias current drift TC (-I
36、IN) 3/ 2 01 -165 +165 nA/C 3 -415 +415 Average output offset voltage drift TC (VOO) 3/ 2 01 -300 +300 V/C 3 -400 +400 Output voltage swing +VONo load 3/ 4 01 +3.2 V 5,6 +3.0 -VO4 -3.2 5,6 -3.0 Quiescent supply current ICCNo load 1,2,3 01 38 mA See footnotes at end of table. Provided by IHSNot for Re
37、saleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Cond
38、itions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min MaxStatic and dc characteristics continued. Power supply sensitivity PSS V+ = +4.5 V to +5.0 V, V- = -4.5 V to -5.0 V, output referred dc 1,2,3 01 28 mV/V Gain controlled input voltage VG3/ 1,2,3 01 0
39、 2 V Common mode rejection ratio CMRR VCM= 1.0 V 3/ 4,5,6 01 59 dB Input offset current IIO3/ 1,2 01 2 A 3 4 Average input offset current drift TC(IIO) 3/ 2 01 20 A/C 3 40 Gain accuracy GACCU AV= 20 dB, 3/ 4,5 01 -0.5 +0.5 dB RF= 1 k, RG= 182 6 -1.0 +1.0 Integral signal nonlinearity SGNL VOUT= 4 VPP
40、3/ 4,6 01 0.1 % 5 0.2 Differential voltage range +VDMRG= 182 3/ 4,6 01 +250 mV 5 +210 -VDM4,6 -250 5 -210 Signal input resistance RIN3/ 4,5 01 100 k 6 50 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIR
41、CUIT DRAWING SIZE A 5962-91694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/
42、 Unit Min MaxStatic and dc characteristics continued. Signal input capacitance CIN3/ 4,5,6 01 2 pF Gain controlled input resistance RINC3/ 4,5 01 600 6 535 Gain controlled input capacitance CINC3/ 4,5,6 01 2 pFCommon mode voltage range +VCMNo load 3/ 4,5 01 +2 V 6 +1.4 -VCM4,5 -2 6 -1.4 Output curre
43、nt +IOUT3/ 4,5 01 +50 mA 6 +30 -IOUT4,5 -50 6 -30 Output impedance ROUTAt dc 3/ 4,5 01 0.2 6 0.3 Frequency domain response Gain flatness peaking low GFPL 0.1 MHz to 30 MHz, 4 01 0.3 dB VOUT 0.5 VPP5,6 0.4 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permi
44、tted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwis
45、e specified Group A subgroups Device type Limits 2/ Unit Min MaxFrequency domain response - continued Gain flatness peaking high GFPH 0.1 MHz to 200 MHz, 4 01 0.5 dB VOUT 0.5 VPP5,6 0.7 Gain flatness rolloff GFR 0.1 MHz to 30 MHz, 4 01 0.3 dB VOUT 0.5 VPP5,6 0.4 0.1 MHz to 60 MHz, 4 1.0 VOUT 0.5 VPP
46、5,6 1.3 Small signal bandwidth SSBW -3 dB bandwidth, 4,5 01 120 MHz VOUT 0.5 VPP6 110 Large signal bandwidth LSBW -3 dB bandwidth, 3/ 4,5 01 100 MHz VOUT 4 VPP6 85 Gain control channel small signal bandwidth SBWC -3 dB bandwidth, 3/ VOUT 0.5 VPP, VIN= +0.2 V, VG= +1 V dc 4,5,6 01 80 MHz Linear phase
47、 deviation LPD 0.1 MHz to 60 MHz 3/ 4 01 1 Degrees 5,6 1.2 Feedthrough FDTH VIN= -22 dBm at 30 MHz, VG= 0 V 3/ 4,5,6 01 -35 dB Time domain response 2 nd harmonic distortion HD2 2 VPP, 20 MHz 4,6 01 -40 dBc 5 -35 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networkin
48、g permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-91694 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 9 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min MaxTime domain response - continued 3 rd harmonic distortion HD3 2 VPP, 20 MHz 4,6 01 -50 dBc 5 -45 Equivalent output no
