1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate to current MIL-PRF-38535 requirements. - MAA 08-07-15 Thomas M. Hess REV SHEET REV SHEET REV A A SHEET 15 16 REV A A A A A A A A A A A A A A REV STATUS OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Josep
2、h A. Kerby CHECKED BY Monica L. Poelking DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 http:/www.dscc.dla.mil APPROVED BY Monica L. Poelking DRAWING APPROVAL DATE 93-11-18 MICROCIRCUIT, DIGITAL, BICMOS OCTAL BUS TRANSCEIVERS AND REGISTERS WITH THREE-STATE OUTPUTS, TTL COMPATIBLE, MONOLI
3、THIC SILICON SIZE A CAGE CODE 67268 5962-91724 STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A REVISION LEVEL A SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E441-08 Provided by IHSNot for ResaleNo reproduction or netwo
4、rking permitted without license from IHS-,-,-SIZE A 5962-91724 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reli
5、ability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PI
6、N is as shown in the following example: 5962 - 91724 01 M K A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA mar
7、ked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Devic
8、e type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54BCT648 Octal bus transceivers and registers with three-state outputs, TTL compatible.1.2.3 Device class designator. The device class designator is a single letter identifying the
9、product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. Q or V Certification and qualification to MIL-PRF-38535 1.2.
10、4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style K GDFP2-F24 or CDFP3-F24 24 Flat pack L GDIP3-T24 or CDIP4-T24 24 Dual-in-line 3 CQCC1-N28 28 Square leadless chip carrier 1.2.5 Lead finish. The lea
11、d finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-91724 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUM
12、BUS, OHIO 43218 - 3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc Input voltage range (I/O ports) . -0.5 V dc to +5.5 V dc Input voltage range (excluding I/O ports) . -0.5 V dc to +7.0 V dc Voltage applied t
13、o any outputs in the disabled state -0.5 V dc to +5.5 V dc Voltage applied to any outputs in the high state. -0.5 V dc to VCCInput clamp current . -30 mA Current into any output in the low state+96 mA Power dissipation (PD ). +574 mW Storage temperature range (TSTG) . -65C to +150C Lead temperature
14、(soldering, 10 seconds).+300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Minimum high level input voltage (VIH).+2.0 V dc Maximum low level input voltage (V
15、IL)+0.8 V dc Maximum input clamp current (IIC) .-18 mA Maximum high level output current (IOH) -12 mA Maximum low level output current (IOL) +48 mA Minimum setup time (ts) A or B before CAB or CBA going high. 6.0 ns Minimum hold time (th) A or B after CAB or CBA going high 1.0 ns Minimum pulse durat
16、ion (tw): CBA or CAB high 4.3 ns CBA or CAB low. 7.5 ns Maximum clock frequency (fclock) 67 MHz Case operating temperature range (TC). -55C to +125C 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performanc
17、e and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits of the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. Provided by IHSNot for ResaleNo reproduction or networking permitted wit
18、hout license from IHS-,-,-SIZE A 5962-91724 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards,
19、and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPA
20、RTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these d
21、ocuments are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein
22、, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL
23、-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535,
24、appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device c
25、lass M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Block or Logic diagram. The block or logic diag
26、ram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-91724 STANDARD MICROCIRCUIT DRA
27、WING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and post-irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post-irradiation paramete
28、r limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part s
29、hall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using t
30、his option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V
31、 shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in orde
32、r to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior
33、 to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A
34、certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA
35、 of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers faci
36、lity and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 129 (see MIL-PRF-38535, append
37、ix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-91724 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance character
38、istics. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified VCCGroup A subgroups Min Max Unit VOH1For all inputs affecting output under test, VIN= 2.0 V or 0.8 V IOH= -3 mA 4.5 V 1, 2, 3 2.4 High level output voltage 3006
39、 VOH2For all inputs affecting output under test, VIN= 2.0 V or 0.8 V IOH= -12 mA 4.5 V 1, 2, 3 2.0 V Low level output voltage 3007 VOLFor all inputs affecting output under test, VIN= 2.0 V or 0.8 V IOL= +48 mA 4.5 V 1, 2, 3 0.55 V Negative input clamp voltage 3022 VIC-For input under test, IIN= -18
40、mA 4.5 V 1, 2, 3 -1.2 V For input under test, VIN= 5.5 V 1, 2, 3 +1.0 mA Control inputs For input under test, VIN= 2.7 V 1, 2, 3 +20 A Input current high 3010 IIH 4/ A or B ports For input under test, VIN= 2.7 V 5.5 V 1, 2, 3 +70 A Control inputs For input under test, VIN= 0.5 V 1, 2, 3 -0.7 Input c
41、urrent low 3009 IIL 4/ A or B ports For input under test, VIN= 0.5 V 5.5 V 1, 2, 3 -0.7 mA Output short circuit current 3011 IOS 5/ VOUT= 0.0 V 5.5 V 1, 2, 3 -100 -225 mA Quiescent supply current outputs high 3005 ICCHVIN= 4.5 V IOUT= 0.0 A 5.5 V 1, 2, 3 13 mA Quiescent supply current outputs low 30
42、05 ICCLVIN= GND IOUT= 0.0 A 5.5 V 1, 2, 3 66 mA Quiescent supply current outputs disabled 3005 ICCZVIN= GND IOUT= 0.0 A 5.5 V 1, 2, 3 16 mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-91724 STANDARD MICR
43、OCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless other
44、wise specified VCCGroup A subgroups Min Max Unit Functional test 6/ Verify output, VOUT See 4.4.1b 4.5 V and 5.5 v 7, 8 L H 5.0 V 9 3.7 10.3 Propagation delay time, CBA or CAB to A or B 3003 tPLH1 7/ CL= 50 pF minimum RL= 500 See figure 4 4.5 V and 5.5 V 10, 11 3.7 13.4 ns 5.0 V 9 4.3 10.6 Propagati
45、on delay time, CBA or CAB to A or B 3003 tPHL1 7/ CL= 50 pF minimum RL= 500 See figure 4 4.5 V and 5.5 V 10, 11 4.3 13.2 ns 5.0 V 9 3.8 9.9 Propagation delay time, A or B to B or A 3003 tPLH2 7/ CL= 50 pF minimum RL= 500 See figure 4 4.5 V and 5.5 V 10, 11 3.8 12.8 ns 5.0 V 9 3.3 8.9 Propagation del
46、ay time, A or B to B or A 3003 tPHL2 7/ CL= 50 pF minimum RL= 500 See figure 4 4.5 V and 5.5 V 10, 11 3.3 11.2 ns 5.0 V 9 3.3 8.4 Propagation delay time, SAB or SBA (with A or B high) to A or B 3003 tPLH3 8/ CL= 50 pF minimum RL= 500 See figure 4 4.5 V and 5.5 V 10, 11 3.3 10.7 ns 5.0 V 9 5.3 12.6 P
47、ropagation delay time, SAB or SBA (with A or B high) to A or B 3003 tPHL3 8/ CL= 50 pF minimum RL= 500 See figure 4 4.5 V and 5.5 V 10, 11 5.3 16.5 ns 5.0 V 9 4.6 11.7 Propagation delay time, SAB or SBA (with A or B low) to A or B 3003 tPLH4 8/ CL= 50 pF minimum RL= 500 See figure 4 4.5 V and 5.5 V
48、10, 11 4.6 15.5 ns 5.0 V 9 4.9 11.1 Propagation delay time, SAB or SBA (with A or B low) to A or B 3003 tPHL4 8/ CL= 50 pF minimum RL= 500 See figure 4 4.5 V and 5.5 V 10, 11 4.9 13.8 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-91724 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218 - 3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97
