1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R057-95. 95-01-19 K. Cottongim B Made technical changes to table I for the IEE, VTH, VOUT, tf1, tr1, tf2, and tr2tests. Redrew entire document. -sld 97-08-07 K. Cottongim C Rewrite paragraphs 4.2.a.2. and 4.3.3
2、.b.2 to add TC. Table I, Output high voltage test condition, correct IOHfrom -3.4 mA to +3.4 mA. 04-07-16 Raymond Monnin D Updated drawing paragraphs. -sld 12-02-21 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPAR
3、ED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY Kendall A. Cottongim MICROCIRCUIT, H
4、YBRID, LINEAR, DUAL REDUNDANT, REMOTE TERMINAL, BUS INTERFACE UNIT DRAWING APPROVAL DATE 93-03-08 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-92162 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E162-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS
5、-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92162 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and
6、 lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 92162 01 H X X Federal RHA Device Device Case Le
7、ad stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with
8、the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 BUS-63153 Small Terminal Interface Circuit (STIC), -15 V 02 BUS-63154 Small Terminal Interface Circ
9、uit (STIC), -12 V 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class
10、 G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space h
11、igh reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test)
12、 periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition
13、document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot fo
14、r ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92162 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and
15、 as follows: Outline letter Descriptive designator Terminals Package style X See figure 1 70 Plug-in package (ceramic) Y See figure 1 70 Flat pack (ceramic) 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ VDDsupply voltage range . -0.5 V dc
16、 to +7.0 V dc VEEsupply voltage range: Device type 01 -18 V dc to +0.3 V dc Device type 02 -15 V dc to +0.3 V dc Input voltage range -0.5 V dc to VDD+ 0.5 V dc Differential input voltage 2/ 50 Vp-p Storage temperature range -65 C to +150 C Power dissipation (PD) . 3/ Lead temperature (soldering, 10
17、seconds) +300 C Junction temperature (TJ) +160 C Thermal resistance, junction-to-case (qJC) . +5.54 C/W 1.4 Recommended operating conditions. VDDsupply voltage range . +4.5 V dc to +5.5 V dc VEEsupply voltage range: Device type 01 -15.75 V dc to -14.25 V dc Device type 02 -12.75 V dc to -11.25 V dc
18、Case operating temperature range (TC) -55 C to +125 C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these docu
19、ments are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1553 - Digital Time Division Command/Response Multiple
20、x Data Bus. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Applies between pins TX/RX A and
21、TX/RX A, and TX/RX B and TX/RX B. 3/ Power dissipation shall be as follows: Condition Device type 01 Device type 02 Hottest die (idle) 0.680 W 0.590 W Total hybrid idle 1.325 W 1.295 W Hottest die (50% duty cycle) 1.450 W 1.360 W Total hybrid (50% duty cycle) 2.575 W 2.220 W Provided by IHSNot for R
22、esaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92162 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawin
23、gs. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a con
24、flict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item p
25、erformance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device
26、 class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the
27、device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Term
28、inal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram. The block diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table
29、I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall
30、be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein sha
31、ll maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be m
32、aintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certi
33、ficate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with eac
34、h lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92162 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I.
35、Electrical performance characteristics. Test Symbol Conditions 1/ -55 C TC +125 C unless otherwise specified Group A subgroups Device type Limits Unit Min Max +5.0 V supply current IDDVDD= +5.5 V, idle duty cycle 1,2,3 All 10 115 mA -15 V/-12 V supply current IEEVEE= -15.75 V, idle duty cycle 1,2,3
36、01 -10 -50 mA VEE= -12.75 V, idle duty cycle 1,2,3 02 -10 -50 mA VEE= -15.75 V, 50% duty cycle, A or B bus, less the idle duty cycle 1,2,3 01 -10 -125 mA VEE= -12.75 V, 50% duty cycle, A or B bus, less the idle duty cycle 1,2,3 02 -10 -135 mA Input high current IIHCS, WRT, TEST MODE, DB00 - 15, and
37、A00 - 13, VIN= 2.7 V 1,2,3 All 20 mA All other inputs, VIN= 2.7 V 1,2,3 All 5.0 mA Input low current IILCS, WRT, TESTMODE, DB00 - 15, and A00 - 13, VIN= 0.4 V 1,2,3 All 20 mA All other inputs, VIN= 0.4 V 1,2,3 All 5.0 mA Output high current 2/ IOH1,2,3 All +3.4 mA Output low current 2/ IOL1,2,3 All
38、-3.4 mA Input high voltage 2/ VIH 1,2,3, All 2.0 V Input low current 2/ VIL1,2,3 All 0.8 V Output high voltage VOHIOH= +3.4 mA 1,2,3 All 3.7 V IOH= 0 mA 2/ 1,2,3 All VCC- 0.4 V Output low voltage VOLIOL= -3.4 mA 1,2,3 All 0.5 V IOL= 0 mA 2/ 1,2,3 All 0.4 V Receiver differential input resistance 2/ 3
39、/ 4/ 5/ 6/ 7/ RIN4,5,6 All 4 kW See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92162 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR
40、 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55 C TC +125 C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Receiver differential input capacitance 2/ 3/ 4/ 5/ 6/ 7/ CIN4,5,6 All 10 pF Receiver threshold voltage VTHTransform
41、er coupled, measured on stub 4,5,6 All 500 860 mVp-p Receiver common mode voltage 2/ 8/ VCM4,5,6 All 10 Vpk Transmitter differential output voltage VOUTDirect coupled across 35 ohm load 2/ 4,5,6 All 6.0 9.0 Vp-p Transformer coupled on stub, 70 ohm load 4,5,6 01 20 27 Vp-p 02 18 27 Transmitter differ
42、ential output noise 2/ enDirect coupled across 35 ohm load 4,5,6 All 10 mVp-p Transmitter output offset voltage 9/ VOSTransformer coupled across 70 ohm load 4,5,6 All 250 mV Functional tests FT Limited 10/ 7,8A,8B All Full 11/ 7,8A,8B All Status sync fall time tf19,10,11 All 100 300 ns Data sync ris
43、e time tr19,10,11 All 100 300 ns Data bit fall time tf29,10,11 All 100 300 ns Data bit rise time tr29,10,11 All 100 300 ns 1/ Unless otherwise specified, +4.5 V dc VDD +5.5 V dc, -15.75 V dc VEE -14.25 V dc for device type 01, -12.75 V dc VEE -11.25 V dc for device type 02. 2/ Parameter shall be tes
44、ted as part of device initial characterization and after design and process changes. Parameter shall be guaranteed to the limits specified in table I for all lots not specifically tested. 3/ Specifications include both transmitter and receiver (tied together internally). 4/ Impedance measurements ap
45、ply between pins TX/RX A and TX/RX A, and TX/RX B and TX/RX B. 5/ It is assumed that all power and ground inputs to the device are connected and that the device case is connected to ground for the impedance measurement. 6/ The specifications are applicable for both unpowered and powered conditions.
46、7/ Impedance specifications assume a 2 volt rms balanced, differential, sinusoidal input. The applicable frequency range is 75 kHz to 1 MHz. 8/ Assumes a common mode voltage within the frequency range of dc to 2 MHz, applied to pins of isolation transformer on stub side (either direct or transformer
47、 coupled), referenced to device ground. Transformer must have a minimum CMRR of 50 dB. 9/ Measured after data words 0000H, FFFFH, 5555H, AAAAH, 7FFFH, and 8000H. 10/ This is a quick digital test that verifies each digital input and each digital output. 11/ This is a comprehensive test of the MIL-STD
48、-1553 interface, internal core logic, and subsystem interface of the device under test. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92162 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Inches mm Inches mm .005 .13 | .400 10.16 .018 .46 | .600 15.24 .050 1.27 | 1.000 25.40 .100 2.54 | 1.600 40.64 .
