1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update the boilerplate to current requirements as specified in MIL-PRF-38535. Editorial changes throughout. jak 06-12-06 Thomas M. Hess REV SHET REV SHET REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14
2、PMIC N/A PREPARED BY Joseph A. Kerby STANDARD MICROCIRCUIT DRAWING CHECKED BY Thomas J. Ricciuti DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Joseph A. DuPay AND AGENCIES OF THE DEPARTMENT OF DEFENSE
3、DRAWING APPROVAL DATE 93-06-29 MICROCIRCUIT, DIGITAL, FAST CMOS, 1-OF-8 DECODER WITH ENABLE, TTL COMPATIBLE INPUTS AND LIMITED OUTPUT VOLTAGE SWING, MONOLITHIC SILICON AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-92233 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E635-06 Provided by IHSNot for
4、ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92233 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1.1 Scope. This drawing documents two product assurance class levels cons
5、isting of high reliability (device classes M and Q) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance (RHA) levels are reflected in the
6、PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92233 01 M E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device class
7、es Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA d
8、evice. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01, 02 54FCT138T 1-of-8 decoder with enable, TTL compatible inputs and limited output voltage swing 03, 04 54FCT138AT 1-of-8 decoder with enable, TTL compatible input
9、s and limited output voltage swing 05, 06 54FCT138CT 1-of-8 decoder with enable, TTL compatible inputs and limited output voltage swing 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements d
10、ocumentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-183
11、5 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or
12、 MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92233 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3
13、 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc DC input voltage range (VIN) . -0.5 V dc to VCC + 0.5 V dc 4/ DC output voltage range (VOUT) -0.5 V dc to VCC+ 0.5 V dc 4/ DC input clamp current (IIK) (VIN= -0.5 V) -20 mA DC output clamp current (IOK) (VOUT= -0
14、.5 V and +7.0 V) 20 mA DC output source current (per output) (IOH) -30 mA DC output sink current (per output) (IOL) . +70 mA DC VCCcurrent (ICC) . 252 mA DC GND current (IGND) . +572 mA Storage temperature range (TSTG) -65C to +150C Case temperature range under bias (TBIAS) -65C to +135C Maximum pow
15、er dissipation (PD) 500 mW Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recommended operating conditions 2/ 3/ Supply voltage range (VCC) . +4.5 V dc to +5.5 V dc Input voltage range (VIN) . 0.0 V to V
16、CC Output voltage range (VOUT) 0.0 V to VCCMaximum low level input voltage (VIL). 0.8 V Minimum high level input voltage (VIH) 2.0 V Case operating temperature range (TC) -55C to +125C Maximum input rise or fall rate (tr, tf): (from VIN= 0.3 V to 2.7 V, 2.7 V to 0.3 V) 5 ns/V Maximum high level outp
17、ut current (IOH): Devices 01, 03, and 05 . -12 mA Devices 02, 04, and 06 . -6 mA Maximum low level output current (IOL) . 32 mA 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliabil
18、ity. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ For VCC 6.5 V, the upper limit on the range is limited to 7.0 V. Provided by IHSNot for ResaleNo
19、 reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92233 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. T
20、he following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufac
21、turing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Mi
22、crocircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a confl
23、ict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item req
24、uirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item require
25、ments for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level C devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device
26、classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specifie
27、d on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless oth
28、erwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. Test conditions for these specified characteristics and limits are as specified in table I. 3.4 Electri
29、cal test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A
30、5962-92233 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number i
31、s not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M sha
32、ll be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certifi
33、cate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order
34、 to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MI
35、L-PRF-38535 and herein or for device class M the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each l
36、ot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review
37、for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment
38、 for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 39 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92233 DEFENSE SUPP
39、LY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Device type VCCGroup A subgroups Limits 3/ UnitConditions 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specifie
40、d Min Max 01, 03, 05 3.0 VCC- 0.5 VOH14/ For all inputs affecting output under test, VIN= VIHor VILVIL= 0.8 V VIH= 2.0 V For all other inputs, VIN= VCCor GND IOH= -300 A 02, 04, 06 4.5 V 2.7 VCC- 0.5 IOH= -12 mA 01, 03, 05 2.4 VCC- 0.5 IOH= -6 mA 2.4 VCC- 0.5 High level output voltage 3006 VOH2For a
41、ll inputs affecting output under test, VIN= VIHor VILVIL= 0.8 V VIH= 2.0 V For all other inputs, VIN= VCCor GND IOH= -12 mA 02, 04, 06 4.5 V 1, 2, 3 2.0 VCC- 0.5 V VOL14/ For all inputs affecting output under test, VIN= VIHor VILVIL= 0.8 V VIH= 2.0 V For all other inputs, VIN= VCCor GND IOL= 300 A A
42、ll 4.5 V 0.20 Low level output voltage 3007 VOL2For all inputs affecting output under test, VIN= VIHor VILVIL= 0.8 V VIH= 2.0 V For all other inputs, VIN= VCCor GND IOL= 32 mA All 4.5 V 1, 2, 3 0.55 V For input under test, IIN= -15 mA 01, 03, 05 -1.3 Negative input clamp voltage 3022 VIC-For input u
43、nder test, IIN= -18 mA 02, 04, 06 4.5 V 1, 2, 3 -1.2 V 1 0.1 01, 03, 05 2, 3 1.0 1, 2 1.0 High level input current 3010 IIHFor input under test, VIN= VCCFor all other inputs, VIN= VCCor GND 02, 04, 06 5.5 V 3 5.0 A 1 -0.1 01, 03, 05 2, 3 -1.0 1, 2 -1.0 Low level input current 3009 IILFor input under
44、 test, VIN= GND For all other inputs, VIN= VCCor GND 02, 04, 06 5.5 V 3 -5.0 A See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92233 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHI
45、O 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test and MIL-STD-883 test method 1/ Symbol Device type VCCGroup A subgroups Limits 3/ Unit Conditions 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Min Max Input capac
46、itance 3012 CIN5/ See 4.3.1b TC= +25C All GND 4 10 pF Output capacitance 3012 COUT5/ See 4.3.1b All GND 4 12 pF Short circuit output current 3005 IOS6/ For all inputs, VIN= VCCor GND VOUT= GND All 5.5 V 1, 2, 3 -60 -225 mA 01, 03, 05 0.25 Dynamic power supply current ICCD4/ 7/ Outputs open 02, 04, 0
47、6 5.5 V 4, 5, 6 0.30 mA/ MHz Bit Quiescent power supply current delta (TTL input levels) 3005 ICC8/ For input under test, VIN= VCC 2.1 V For all other inputs, VIN= VCCor GND All 5.5 V 1, 2, 3 2.0 mA Quiescent power supply current output high 3005 ICCHE1 = E2 = GND, E3 = VCCFor all other inputs, VIN=
48、 VCCor GND All 5.5 V 1, 2, 3 1.5 mA Quiescent power supply current output low 3005 ICCLE1 = E2 = GND, E3 = VCCFor all other inputs, VIN= VCCor GND All 5.5 V 1, 2, 3 1.5 mA 01, 03, 05 4.0 For switching inputs VIN= VCCor GND 02, 04, 06 4.5 01, 03, 05 5.0 Total power supply current ICCT9/ Outputs open E1, E2, or E3 toggling One bit toggling fi= 10 MHz 50% duty cycle For nonswitching inputs VIN= VCCor GND For switching inputs VIN= 3.4 V or GND 02, 04, 06 5.5 V 4, 5, 6 5.5 mA All 4.5 V 7, 8 L H Functional tests 10/ VIL= 0.8 V VIH= 2.0 V Verify
