1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A NOR 5962-R065-94. 93-12-08 M. L. Poelking B Add case outline Z. Made technical changes in table I. Editorial changes throughout. 94-07-14 M. L. Poelking C Update drawing to current requirements. Editorial changes throughout. - gap 10-05-20 Charle
2、s F. Saffle REV SHET REV C C SHET 15 16 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Larry T. Gauder DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAIL
3、ABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Thanh V. Nguyen APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ECL, QUINTUPLE DIFFERENTIAL LINE RECEIVER, MONOLITHIC SILICON DRAWING APPROVAL DATE 93-08-31 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 596
4、2-92343 SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E156-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92343 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234
5、APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). Wh
6、en available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 92343 01 M Y X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) L
7、eadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA leve
8、ls and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 10E516 Quintuple differential line receiver 02 100E516 Quintuple differentia
9、l line receiver, temperature compensated 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN
10、 class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style Y See figure 1
11、28 Quad flat pack Z See figure 2 29 Pin grid array 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR
12、D MICROCIRCUIT DRAWING SIZE A 5962-92343 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VEE) 2/ . -8.0 V dc to 0.0 V dc Input voltage range (VIN) 2/ -6.0 V dc to 0.0 V dc Minimum input swi
13、ng (VPP) 0.150 V dc Output current (IOUT) Continuous 50 mA Surge . 100 mA Storage temperature range . -65C to +165C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) +165C Maximum power dissipation (PD): Device type 01 . 195 mW Device type 02 . 220 mW Thermal resistance, junct
14、ion-to-case (JC): Case Y . 1.23C/W Case Z . 6.44C/W 1.4 Recommended operating conditions. Supply voltage range (VEE): 2/ Device type 01 . -5.46 V dc to -4.94 V dc Device type 02 . -5.46 V dc to -4.20 V dc Input voltage range (VIN): 2/ Device type 01 . -1.950 V dc to -0.660 V dc Device type 02 . -1.8
15、10 V dc to -0.880 V dc Output voltage range (VOUT): 2/ Device type 01 . -1.972 V dc to -0.672 V dc Device type 02 . -1.810 V dc to -0.880 V dc Input rise and fall times, 20% to 80% (tr, tf) . 500 ps maximum Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government sp
16、ecification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-
17、PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcirc
18、uit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolute max
19、imum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Ratings apply when referenced to VCC= 0.0 V dc. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD
20、 MICROCIRCUIT DRAWING SIZE A 5962-92343 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precede
21、nce. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as
22、 modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B dev
23、ices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case
24、outline(s) shall be in accordance with 1.2.4 herein and figures 1 and 2. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 3. 3.2.3 Truth table. The truth table shall be as specified on figure 4. 3.2.4 Logic diagram. The logic diagram shall be as specified on figur
25、e 5. 3.2.5 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 6. 3.2.6 Inner-layer dielectric. Polyimide and silicon coatings are allowed as part of the wafer fabrication process provided that each microcircuit inspection lot (see MIL-PRF-3
26、8535, “Inspection lot - class B“) shall be subjected to and pass the internal water vapor content test in accordance with group D6 of test method 5005 of MIL-STD-883. The frequency of the internal water vapor testing may not be decreased unless approved by the preparing activity. 3.3 Electrical perf
27、ormance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirement
28、s. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking
29、of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535.
30、Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-
31、38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be require
32、d from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q
33、 and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix
34、A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawi
35、ng. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92343 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristic
36、s. Test Symbol Conditions -55C TC +125C Group A subgroupsDevice type Limits 1/ Unit unless otherwise specified Min Max High level input voltage VIH-5.46 V VEE -4.94 V for type 01 -5.46 V VEE -4.20 V for type 02 1 2 3 01 -1.130 -1.020 -1.258 -0.810 -0.660 -0.906 V 1, 2, 3 02 -1.165 -0.880 Low level i
37、nput voltage VIL1, 3 2 01 -1.950 -1.950 -1.480 -1.421 V 1, 2, 3 02 -1.810 -1.475 High level output voltage VOHVCC= VCCO= GND VBB= open VIN= VIHmaximum, VILminimum Outputs terminated through 50 to -2.0 V VEE= -4.94 V 1 2 3 01 -0.980 -0.862 -1.097 -0.810 -0.672 -0.906 V EE= -4.20 V 1, 2 3 02 -1.025 -1
38、.097 -0.880 -0.880 Low level output voltage VOLVEE= -5.46 V 1 2 3 01 -1.950 -1.934 -1.972 -1.630 -1.579 -1.652 V VEE= -5.46 V 1, 2 3 02 -1.810 -1.810 -1.620 -1.600 High level threshold output voltage VOHTVCC= VCCO= GND VBB= open VIN= VIHminimum, VILmaximum Outputs terminated through 50 to -2.0 V VEE
39、= -5.46 V 1 2 3 01 -0.980 -0.862 -1.097 -0.810 -0.672 -0.906 V 1, 2 3 02 -1.025 -1.097 -0.880 -0.880 Low level threshold output voltage VOLTVEE= -4.94 V 1 2 3 01 -1.950 -1.934 -1.972 -1.630 -1.579 -1.652 V VEE= -4.20 V 1, 2 3 02 -1.810 -1.810 -1.620 -1.600 Common mode range high (output high) VCMR1V
40、CC= VCCO= GND VBB= open VIN= -2.0 V or -2.15 V Outputs terminated through 50 to -2.0 V VEE= -5.20 V 1 2 3 01 -0.980 -0.862 -1.097 -0.810 -0.672 -0.906 V EE= -5.20 V 1, 2 3 02 -1.025 -1.097 -0.880 -0.880 Common mode range high (output low) VCMR2VEE= -5.20 V 1 2 3 01 -1.950 -1.934 -1.972 -1.630 -1.579
41、 -1.652 V VEE= -5.20 V 1, 2 3 02 -1.810 -1.810 -1.620 -1.600 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92343 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVIS
42、ION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroupsDevice type Limits 1/ Unit Min Max Common mode range low (output high) VCMR3VCC= VCCO= GND VBB= open VIN= -0.75 V or
43、 -0.6 V Outputs terminated through 50 to -2.0 V VEE= -5.20 V 1 2 3 01 -0.980 -0.862 -1.097-0.810-0.672-0.906V EE= -5.20 V 1, 2 3 02 -1.025 -1.097-0.880-0.880Common mode range low (output low) VCMR4VCC= VCCO= GND VBB= open VIN= -0.75 V or -0.6 V Outputs terminated through 50 to -2.0 V VEE= -5.20 V 1
44、2 3 01 -1.950 -1.934 -1.972 -1.630 -1.579 -1.652 V EE= -5.20 V 1, 2 3 02 -1.810 -1.810 -1.620 -1.600 Input sensitivity range high (output high) VPP1VCC= VCCO= GND VBB= open VIN= -0.6 V or -1.6 V Outputs terminated through 50 to -2.0 V VEE= -5.20 V 1 2 3 01 -0.980 -0.862 -1.097 -0.810 -0.672 -0.906 V
45、 EE= -5.20 V 1, 2 3 02 -1.025 -1.097 -0.880 -0.880 Input sensitivity range high (output low) VPP2VEE= -5.20 V 1 2 3 01 -1.950 -1.934 -1.972 -1.630 -1.579 -1.652 V VEE= -5.20 V 1, 2 3 02 -1.810 -1.810 -1.620 -1.600 Input sensitivity range low (output high) VPP3VCC= VCCO= GND VBB= open VIN= -2.0 V or
46、-3.0 V Outputs terminated through 50 to -2.0 V VEE= -5.20 V 1 2 3 01 -0.980 -0.862 -1.097 -0.810 -0.672 -0.906 V EE= -5.20 V 1, 2 3 02 -1.025 -1.097 -0.880 -0.880 Input sensitivity range low (output low) VPP4VEE= -5.20 V 1 2 3 01 -1.950 -1.934 -1.972 -1.630 -1.579 -1.652 V VEE= -5.20 V 1, 2 3 02 -1.
47、810 -1.810 -1.620 -1.600 Reference bias supply voltage VBBVCC= VCCO= GND Outputs terminated through 50 to -2.0 V Inputs are open VEE= -5.46 V 1 2 3 01 -1.350 -1.278 -1.424 -1.250 -1.158 -1.314 V EE= -5.46 V 1, 2, 3 02 -1.380 -1.260 Power supply drain current IEEVCC= VCCO= GND, VBB= open VEE= -5.46 V
48、 VIN= VIHmaximum, VILminimum Outputs terminated through 50 to -2.0 V 1, 2, 3 01 -35 mA 1, 3 2 02 -35 -40 See footnote at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92343 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min Ma
