1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED B Corrected figure 1 to move the side view of case outlines X and Z to the right side of the top view for the correct orientation. Figure 1; removed the min limit for the D dimension of 2.880 inches (73.15 mm) for the case outline Z. Redrew entire
2、document. -sld 98-07-01 K. Cottongim C Update drawing boilerplate. Editorial changes throughout. 03-07-18 Raymond Monnin D Add device type 02. Add 1.5 and footnote 2/. Table 1 add footnote 1/ for enhanced low dose rate effects. Paragraph 4.3.5.a, correct paragraph to add component tested dose rate.
3、Table 1 output voltage, subgroup 1, device type 01 correct (-Vout) max limit from -12.23 to -15.23. In Table I for “Output Voltage, Line Regulation, and Load Regulation” change all “main” to “+Vout” and change all “dual” to “ -Vout”. Table I in conditions column for Isolation test, change TA= 25C to
4、 TC= 25C. Table I Conditions column for Capacitive load test, change TA= 25C to TC= 25C. Table I change footnote 1/ to footnote 2/ to read “Unit will be unconditionally stable with any value of capacitance from 0 to tabled value. Unit will start up with any value of capacitance from 0 to tabled valu
5、e. The start up time and transient response time may change.” gc 06-09-18 Raymond Monnin E Update Table I to include RHA level “P and L“. Update table in paragraph 4.3.5 to include RHA level “P and L “. Update bulletin page to include RHA level “P and L“ part numbers. gc 07-05-31 Robert M. Heber F A
6、dded footnote 1 to table II, under group C end-point electricals. Updated drawing paragraphs. -sld 09-08-18 Charles F. Saffle G Table I: Change PDmax limit for subgroup 1 from “10” W to “12” W. Table I; Change footnote 7/ From “Input step transition time greater than 10 microseconds” to “Input step
7、transition time equal to 100 microseconds 20 percent.” 10-12-06 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV G G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 PMIC N/A PREPARED BY Steve L. Duncan DLA LAND AND MARITIME STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael Jon
8、es COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, 15-VOLT, DUAL CHANNEL, DC/DC CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-05-13 AMSC N/A REVISION LE
9、VEL G SIZE A CAGE CODE 67268 5962-93072 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E073-11Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93072 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G S
10、HEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice
11、of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 93072 01 H X X Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.
12、5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identif
13、y the circuit function as follows: Device type Generic number Circuit function 01 MTR2815D/883, MTR2815DF/883 DC-DC converter, 30 W, 15 V output 02 SMTR2815D, SMTR2815DF DC-DC converter, 30 W, 15 V output 1.2.3 Device class designator. This device class designator shall be a single letter identifyin
14、g the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest r
15、eliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This leve
16、l uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of th
17、e other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D
18、 Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Ter
19、minals Package style X See figure 1 10 Dual-in-line Z See figure 1 10 Flange mount Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93072 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET
20、3 DSCC FORM 2234 APR 97 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input voltage range -0.5 V dc to +50 V dc Power dissipation (PD) . 12 W Output power . 30.98 W Lead soldering temperature (10 seconds) . +300C Storage temperature range
21、 -65C to +150C 1.4 Recommended operating conditions. Input voltage range +16 V dc to +40 V dc Case operating temperature range (TC) . -55C to +125C 1.5 Radiation features. Maximum total dose available (dose rate = 9 rad(Si)/s): Device type 02 . 100 krad (Si) 2/ 2. APPLICABLE DOCUMENTS 2.1 Government
22、 specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534
23、 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-H
24、DBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict betw
25、een the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent dam
26、age to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ These parts may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end-point limits for the noted parameters are guaranteed only for
27、 the conditions as specified in MIL-STD-883, method 1019, condition C, tested at 9 rad(Si)/s.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93072 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVE
28、L G SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in th
29、e device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In
30、 addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case out
31、line(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as
32、 specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking
33、 of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device
34、described herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed.
35、This data shall be maintained under document revision level control by the manufacturer and be made available to the preparing activity (DLA Land and Maritime-VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
36、 drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall b
37、e provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shal
38、l not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the m
39、anufacturer under document revision level control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
40、 test method 1015 of MIL-STD-883. (2) TAas specified in accordance with table I of method 1015 of MIL-STD-883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the ma
41、nufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93072 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics
42、. Test Symbol Conditions 1/ -55C TC+125C VIN= 28 V dc 0.5 V dc no external sync, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Output voltage VOUTIOUT= 1.0 A dc, (+Vout) 1 01, 02 +14.85 +15.15 V dc 2,3 +14.55 +15.45 P, L, R 1,2,3 02 +14.30 +15.92 IOUT= 1.0 A dc,
43、(-Vout) 1 01, 02 -14.77 -15.23 2,3 -14.47 -15.53 P, L, R 1,2,3 02 -14.24 -15.73 Output current IOUTVIN= 16 V dc, 28 V dc, and to 40 V dc, sum of both outputs 1,2,3 01, 02 0.0 2000 mA P, L, R 1,2,3 02 0.0 2000 Output ripple voltage VRIPIOUT= 1.0 A B.W. = 10 kHz to 2 MHz 1 01, 02 80 mV p-p 2,3 120 P,
44、L, R 1 02 100 P, L, R 2,3 02 150 VOUTline regulation VRLINEVIN= 16 V dc to 40 V dc, IOUT= 1.0 A (+Vout) 1,2,3 01, 02 50 mV P, L, R 1,2,3 02 60 VIN= 16 V dc to 40 V dc, IOUT= 1.0 A (-Vout) 1,2,3 01, 02 180 P, L, R 1,2,3 02 200 VOUTload regulation VRLOADIOUT= 0 to 1.0 A, (+Vout) 1,2,3 01, 02 50 mV P,
45、L, R 1,2,3 02 60 IOUT= 0 to 1.0 A, (-Vout) 1,2,3 01, 02 180 P, L, R 1,2,3 02 200 Input current IINIOUT= 0, Inhibit (pin 2) = 0 1,2,3 01, 02 8 mA P, L, R 1,2,3 02 10 IOUT= 0, Inhibit (pin 2) = open 1,2,3 01, 02 75 P, L, R 1,2,3 02 85 See footnotes at end of table. Provided by IHSNot for ResaleNo repr
46、oduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93072 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued Test Symbol Conditions 1/ -55C TC+1
47、25C VIN= 28 V dc 0.5 V dc no external sync, CL= 0 unless otherwise specified Group A subgroups Device type Limits Unit Min Max Input ripple current IRIPIOUT= 1.0 A, B.W. = 10 kHz to 10 MHz 1, 2, 3 01, 02 50 mA p-p P, L, R 1, 2, 3 02 60 Efficiency Eff IOUT= 1.0 A 1 01 80 % 2,3 771 02 78 % 2,3 75 P, L
48、, R 1 02 78 P, L, R 2,3 75 Isolation ISO Input to output or any pin to case (except pins 6, 7, and 8) at 500 V dc, TC=+25C 1 01, 02 100 M P, L, R 1 02 100 Capacitive load 2/ 3/ CLNo effect on dc performance, TC=+25C 4 01, 02 500 F P, L, R 4 02 500 Power dissipation, load fault PDShort circuit 1,2,3 01, 02 12 W P, L, R 1,2,3 02 12 Switching frequency FSIOUT= 1.0 A 4,5,6 01, 02 550 650 kHz P, L, R 4,5,6 02 525 675 External sync range 4/ FSYNCIOUT= 1.0 A, TTL level to pin 9 4,5,6 01,
