1、b 0055784 T77 W DEFENSE LOGISTICS AGENCY DEFENSE ELECTRONICS SUPPLY CENTER 1507 WILMINGTON PIKE DAYTON, OH 45444-5765 H RERV REFER n, DESC-ELDC (Mr. Hess/(AV 986) 513-296-8526/tmh) O3 AUG 1934 SUBJECT: Notice of Revision (NOR) 5962-R199-94 for Standardized Military Drawing (SMD) 5962-93176. Military
2、/Inductry Distribution he enclosed NOR is approved for use effective as of the date of the NOR. In accordance with MIL-STD-100 SMD holders should, as a minimum, handwrite those changes described in the NOR to sheet 1 of the subject SMD. After completion, the NOR should be attached to the subject SMD
3、 for future reference. Those companies who were listed as approved sources of supply prior to this action have agreed to actions taken on devices for which they had previously provided DESC a certificate of compliance. This is evidenced by an existing active current certificate of compliance on file
4、 at DESC along with a DESC record of verbal coordination. The certificate of compliance for these devices is considered concurrence with the new revision unless DESC is otherwise notified. DECC has received and accepted a certificate of compliance from Motorola, Cage code 04713, for PIN 5962-9317601
5、QDX, and vendor similiar part number 889141QDAJC. This action will be reflected in the next revision of MIL-EUL-103. If you have comments or questions, please contact Tom Hess at (AV)986-8526 /(513)296-8526. h 1 Encl MONICA L. POELKING J Chief, Custom Microelectronics Branch Provided by IHSNot for R
6、esaleNo reproduction or networking permitted without license from IHS-,-,-9999996 0055785 903 b. ADDRESS (Street, City, State, Zip Code) 5. CAGE CODE 4. ORIGINATOR Defense Electronics Supply Center 67268 1507 Uilmington Pike Dayton, OH 45444-5765 7. CAGE CODE a. TYPED NAME (First, Middle Initial, La
7、st ) 67268 10. REVISION LETTER a. CURRENT b. NEU 9. TITLE OF DOCUMENT MICROCIRCUIT, DIGITAL, CMOS, LOU SKEU CLOCK DRIVER UITH RESET, MONOLITHIC SILICON IN1 TIAL A Form Approved 1. DATE WB NO. 0704-0188 (YYmDD, 94-07- 14 NOTICE OF REVISION (NOR) This revision described below has been authorized for t
8、he docunent listed. 6. NOR NO. 5962-R199-96 8. DOCUHENT NO. 5962-93 176 11. ECP NO. the time for reviewing instructions, searching existing data.sources, gathering a minfaining the ACTIVITY NO. 3. DODAAC Public reporting.kirden-for this cnllection.is estimated to average 2 hours per rrc j-luding dat
9、a needed, a. canp eting and reviewing the collection.of infymation: this burden estimate or an other aspect of this collection of inforination for reduci for InfomTion Operati add liA,ii. Revisions description colum; add “Changes in accordance with NC4 5962-R1W-9411. Revisions date colum; edd ,i194-
10、07-14d,i. Revision level block; add *IAii. Rev status of sheets; For sheets 1, 2, 8 add IaA“. Sheet 2: Paragraph 1.2.6 Case outline(s1 Add: Outline letter Descriptive designator Terminals Package style D CDFPl-Fl4 or CDFP2-F14 14 Flat pack Change revision status to lEA“ Sheet 8: Change fran: Vase CI
11、1 to: Yase C, DIa Change revision status to ilAil d. TITLE CHIEF, CUSTOH MICROELECTRONICS 1Sa. ACTIVITY ACCOMPLISHI NG REVISION DESC-ELDC e. SIGNATURE f. DATE SIGNED (YYi4MDD) Monica L. Poelking 94-07-14 b. REVISION COIIPLETED (Signature) c. DATE SIGNED (YWD 1 Thomas M. Hess 96-07- 14 Provided by IH
12、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-REVISIONS I I I LTR DESCRIPTION DATE (YR-HO-DA) APPROVED PREPARED BY Thoinas M. Hess PMIC N/A CHECKED BY STANJ3ARDIZED MILITARY Christopher A. Rauch DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 THIS D
13、RAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS ANO AGENCIES OF THE DEPARTMENT OF DEFENSE By Poelkiw AMSC #/A MICROCIRCUIT, DIGITAL, CMOS, LOW SKEW CLOCK DRIVER WITH RESET, CRANING APPROVAL DATE 93-12-22 , REVISION LEVEL III MONOLITHIC SILICON 5962-931 76 SIZE CAGE CODE 67268 A SHEET 1 OF 15 I )ESC F
14、ORM 193 - JUL 91 DISTRIBUTION STATEMENT A. Approved for public release: distribution is un1 imited. 5962-E454-93 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-9999996 0055787 786 m z 2- -_i-r 7, _- _Y_a. 7 -. %,II_=-L=. _- AL_ -AcxL-=.%3 -2- I-* 1.
15、 SCOPE 1.1 Scope. This drawing forms a part of a one part - one part nutrer documentation system (see 6.6 herein). Two product assurance classes consisting of military high reliability (device classes Q and M) and space application (device class V). and a choice of case outlines and lead finishes ar
16、e available and are reflected in the Part or Identifying Number (PIN). Device class M microcircuits represent non-JAN class B microcircuits in accordance with 1.2.1 of MIL-STD-883, “Provisions for the use of MIL-STD-883 in conjunction with conpliant non-JAN devices“. When available, a choice of Radi
17、ation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 M. The PIN shall be as shown in the following example: - 5962 93176 o1 M C X I I - 1 I I I I I I I I I Lead finish Case outline Devi ce L Devi ce -1 Federal RHA stock class designator type cass designator (see 1.2.1) (see 1.2.2) des
18、ignator (see 1.2.4) (see 1.2.5) L (see 1.2.3) I Draw i ng number 1.2.1 RHA desianator. Device class M RHA marked devices shall meet the MIL-1-38535 appendix A specified RHA levels and shall be marked with the appropriate RHA designator. Device classes Q and V RHA marked devices shall meet the MIL-1-
19、38535 specified RHA levels and shall be marked with the appropriate RHA designator. non-RHA devi ce. A dash (-) indicates a 1.2.2 Device type(s). The device type(s) shall identify the circuit function as follows: Devi ce type Gener i c number Circuit function o1 88914 Low skew CMOS clock driver with
20、 reset 1.2.3 Device class desiqnator. The device class designator shall be a single letter identifying the product assurance level as follows: Device class Device reauirements documentation M Vendor self-certification to the requirements for non-JAN class El microcircuits in accordance with 1.2.1 of
21、 MIL-STO-883 Q or V Certification and qual if ication to MIL-1-38535 1.2.4 Case outline(s1. The case outline(s) shall be as designated in MIL-STO-1835 and as follows: Outline letter Descriptive des iqnator lermi na 1 s Packaqe style C GDIP1-T14 or COIP2-T14 14 Dua 1 - in- 1 i ne package 1.2.5 Lead f
22、inish. The lead finish shall be as specified in MIL-STD-883 (see 3.1 herein) for class M or MIL-1-38535 for classes Q and V. designation is for use in specifications when lead finishes A, El, and C are considered acceptable and interchangeable without preference. Finish letter “X“ shall not be marke
23、d on the microcircuit or its packaging. The “X“ 5962-93176 REVISION LEVEL SHEET STANDARDIZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 DESC FORM 193A JUL 91 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1.3 Absolute maxi
24、mum ratiws. iJ Supply voltage (referenced to GND) Vcc Input voltage (referenced to GNO) V . Output voltage (referenced to GND) io Output current I . supply current, IC, ri* GD Power dissipation Storage temperature . Lead temperature (soldering, 10 sec) . Junction temperature, Continuous . STANDARD1
25、ZED HILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 -0.5 V dc to 6.0 V dc -0.5 V dC to Vcc t 0.5 V dC -0.5 V dC to Vcc + 0.5 V dC I75 m4 i80 mA 500 mW t300“C +175*C -65C to +130C SIZE 5962-93176 A REVISION LEVEL SHEET 1.4 Recomnended operatinq conditions. Supply voltage (refere
26、nced to GND) Vcc 4.5 V dc to 5.5 V dc Input voltage (referenced to GND) V . O V dc to Vcc Output voltage (referenced to GND) io O V dc to V Case operating temperature range T . -55 to tiI0c Input rise and fall time t . tf O to 10 ns/V Minimum pulse width CP (tw) 1.5 Digital loaic testinp for device
27、classes Q and V. . 3.0 ns Fault coverage measurement of manufacturing logic tests (MIL-STO-883, test method 5012) XX percent 2/ 2. APPLICABLE WCUMENTS 2.1 Government specification. standards, bulletin, and handbook. Unless otherwise specified, the following specification, standards, bulletin, and ha
28、ndbook of the issue listed in that issue of the Department of Defense Index of Specifications and Standards specified in the solicitation, form a part of this drawing to the extent specified here in , SPEC IF ICATION MILITARY MIL-1-38535 - Integrated Circuits, Manufacturing, General Specification fo
29、r. STANDARDS MILITARY MIL-STD-883 - Test Methods and Procedures for Microelectronics. MIL-STD-973 - Configuration Management. MIL-STD-1835 - Microcircuit Case Outlines. BULLETIN MILITARY MIL-BUL-103 - List of Standardized Military Drawings (Ws). ntresses above the absolute maxinum rating may cause p
30、ermanent damage to the device. Extended operation at the maximm levels may degrade performance and affect reliability. 21 Values will be added when they become available. DESC FORM 193A JUL 91 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-HANDBOOK
31、S TANDARDI 2 ED MILITARY DMMING DEFENSE ELECTRONICS SUPPLY CENTW DAYTON, OHIO 45444 MILITARY MIL-HDBK-780 - Standardized Military Drawings. (Copies of the specification, standards, bulletin, and handbook required by manufacturers in connection with specific acquisition functions should be obtained f
32、rom the contracting activity or as directed by the contracting act i v i ty . ) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing shall take precedence. 3. REQUIREMENTS SIZE 5962-93176 A REVISION LEVEL SHEET
33、 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-W 999999b 0055770 270 STANDARDIZ MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 3.9 Verification and review for device class M. For device class M. DESC, DESCs agent, and the a
34、cquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall k made available onshore at the option of the reviewer. microcircuit group nftary requiremiits documents represent different class levels, and previously when
35、a device manufacturer ipgrsded military product from one class level to another, the benefits of the upgraded product were unavailable to :he Original Equipment Manufacturer (OEM), that was contractually locked into the original unique PIN. By ksCabi!shing a one part :unber system covering all thred
36、 documents, the OEM can acquire to the highest class level vailable for a given generic device to neet system needs without modifying the original contract parts selection :ri teria. STANDARDIZED MILITARY DRAWING DEFENSE ELECTRONICS SUPPLY CENTER DAYTON, OHIO 45444 Document Military documeatation fo
37、rmat under new system source listinq listinq Example PIN Hanufactur ing SIZE 5962-93176 A REVISION LEVEL SHEET 15 Jew MIL-H-38534 Standardized Mi 1 itary 5962-XXXXXZZ(H or K)YY QML-38534 Pawings )raw i ngs lew MIL-1-36535 Standardized Hi 1 itary 5962-XXXXXZZ(Q or V)YY QML-38535 MIL -BUL - 103 MIL-BU
38、L-103 lew 1.2.1 of MIL-STD-883 Standardized 5962 -XXXXXZZ i M )YY MIL -BUL - 103 HIL-BUL-103 lilitary Drawings 6.7 Sources of supply. 6.7.1 Sources of suDply for device classes Q and V. Sources of supply for device classes Q and V are listed in JML-38535. The vendors listed in QML-38535 have submitt
39、ed a certificate of compliance (see 3.6 herein) to DESC-EC and lave agreed to this drawing. 6.7.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in YIL-BUL-103. The vendors listed in MIL-BUL-103 have agreed to this drawing and a certificate of compli
40、ance (see 3.6 herein) has been submitted to and accepted by DESC-EC. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-m 777b 0055803 986 m 1 STANDARD I LED MIL I TARY DRAW I NG SOURCE APPROVAL BULLETIN DATE: 93-12-22 Approved sources of stqply for SMD
41、 596243176 are listed belw for immediate acquisition only and shll be added to MIL-BUL-103 during the next revision. MIL-BUL-103 wll be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate nf cornplSance has been submittzd to
42、and accepted by DESC-EC. This bulletin is superseded by the next dated revision of HIL-BUL-103. I I I I Vendor I Vendor l I I I I I I I I I I I I Standardized I PIN military drawing I 5962-9317601QCX I 04713 I 88914/BCAJC I iJ Caution. Do not use this .iumi)er for item acquisition. may not satisfy t
43、he performance requirements of this drawing. Items acquired to this number Vendor CAGE nunber 04713 Vendor name and address Motorola, Incorporated 5005 E. EfcDowe11 Rd. Phoenix, AZ 85008 Point of contact: 2100 E. Elliot Rd. Tenpe, A2 85284 I 1 1 The information contained herein is disseminated for convenience only and I I the Government assumes no liability whatsoever for any inaccuracies in this I I infomtion bulletin. I I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
