1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add new device types 02 and 03. Add case outline X for Leaded Chip Carrier package for device types 02 and 03 in figure 1. Update boilerplate paragraphs to current requirements of MIL-PRF-38535. - MAA 09-12-10 Thomas M. Hess REV SHET REV A A A A
2、A A A A A SHEET 15 16 17 18 19 20 21 22 23 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Thomas M. Hess DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Thomas M. Hess COLUMBUS, OHIO 43218-3990 http:/www.dscc.d
3、la.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, CMOS, LOW SKEW PLL CLOCK DRIVER, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-03-03 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-93196 S
4、HEET 1 OF 23 DSCC FORM 2233 APR 97 5962-E023-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93196 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1.
5、 SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When availa
6、ble, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 93196 01 Q Y C Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish
7、 (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and ar
8、e marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function Maximum Clock frequency 01 88915 Low skew quad clock driver 55 MHz 02 TS88915T Low skew
9、PLL clock driver, TTL 70 MHz 03 TS88915T Low skew PLL clock driver, TTL 100 MHz 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirem
10、ents for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator
11、Terminals Package style X see figure 1 28 Leaded Ceramic Chip Carrier Y see figure 1 28 Quad Flat package Z see figure 1 29 Pin grid array 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNo
12、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93196 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (reference to
13、 GND) VCC. -0.5 V dc to +6.0 V dc Input voltage range (reference to GND) VIN-0.5 V dc to VCC+ 0.5 V dc 2/ Output voltage range (reference to GND) VOUT. -0.5 V dc to VCC + 0.5 V dc Output current (per pin) IOUT. -50 mA Supply current VCCor GND . -100 mA Maximum power dissipation (PD) : For device typ
14、e 01 . 300 mW For device types 02 and 03 500 mW Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) . +175C Thermal resistance, junction-to-case (JC): For device type 01, case Y . 1.50 C/W For device type 01, case Z 6.74 C/W For device t
15、ypes 02 and 03 Case X and Z 7.0 C/W 1.4 Recommended operating conditions. Supply voltage range (reference to GND) VCC: For device type 01 . 4.5 V dc to +5.5 V dc For device types 02 and 03 . 4.75 V dc to +5.25 V dc Input voltage range (reference to GND) VIN. -0.0 V dc to VCC Output voltage range (re
16、ference to GND) VOUT-0.5 V dc to VCC Case operating temperature range (TC) . -55C to +125C Input rise or fall time rate, tr, tf0 ns to 3.0 ns/v 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and
17、 affect reliability. 2/ Input voltage must not be greater than the supply voltage by more than 2.5 V all times including power-on reset. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93196 DEFENSE SUPPLY CE
18、NTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise sp
19、ecified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - I
20、nterface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardi
21、zation Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes ap
22、plicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Managem
23、ent (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, constructio
24、n, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein on figu
25、re 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.4 Test circuit and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 4. Provided by
26、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93196 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation
27、 parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall b
28、e the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasibl
29、e due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in acco
30、rdance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compl
31、iance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed
32、 as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 a
33、nd herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microc
34、ircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device
35、class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device
36、 class M. Device class M devices covered by this drawing shall be in microcircuit group number 398 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93196 DEFENSE SUPPLY CENTER
37、COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC+125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max High level output voltage VOHVCC=
38、4.5 V, VIH= 2.0 V, VIL= 0.8 V IOH= -36 mA 1, 3 01 3.86 V 2 3.70VCC= 4.75 V, VIH= 2.0 V, VIL= 0.8 V IOH= -36 mA 1, 2, 3 02, 03 4.01 VCC= 4.5 V, VIH= 2.0 V, VIL= 0.8 V IOH= -12 mA (LOCK pin) 2/ 3/ 1, 3 01 3.86 2 3.70VCC= 4.75 V, VIH= 2.0 V, VIL= 0.8 V IOH= -12 mA (LOCK pin) 1, 2, 3 02, 03 4.01 VCC= 5.
39、5 V, VIH= 2.0 V, VIL= 0.8 V IOH= -36 mA 1, 3 01 4.86 2 4.70VCC= 5.25 V, VIH= 2.0 V, VIL= 0.8 V IOH= -36 mA 1, 2, 3 02, 03 4.51 VCC= 4.5 V, VIH= 2.0 V, VIL= 0.8 V IOH= -12 mA (LOCK pin) 2/ 3/ 1, 3 01 4.86 2 4.70VCC= 5.25 V, VIH= 2.0 V, VIL= 0.8 V IOH= -12 mA (LOCK pin) 1, 2, 3 02, 03 4.51 VCC= 5.5 V,
40、 VIH= 2.0 V, VIL= 0.8 V IOH= -88 mA 1, 2, 3 01 3.85 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93196 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL
41、 A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TC+125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Low level output voltage VOLFor device type 01 at VCC= 4.5 V, For device
42、types 02,03 at VCC= 4.75 V, VIH= 2.0 V, VIL= 0.8 V IOL= +36 mA 1, 3 All 0.44 V 2 0.50For device type 01 at VCC= 4.5 V, For device types 02,03 at VCC= 4.75 V, VIH= 2.0 V, VIL= 0.8 V IOL= +12 mA (LOCK pin) 2/ 1, 3 All 0.44 2 0.50For device type 01 at VCC= 5.5 V, For device types 02,03 at VCC= 5.25 V,
43、VIH= 2.0 V, VIL= 0.8 V IOL= +36 mA 1, 3 All 0.44 2 0.50For device type 01 at VCC= 5.5 V, For device types 02,03 at VCC= 5.25 V, VIH= 2.0 V, VIL= 0.8 V IOL= +12 mA (LOCK pin) 2/ 1, 3 All 0.44 2 0.50For device types 02,03 at VCC= 4.75 V, VIH= 2.0 V, VIL= 0.8 V IOL= +15 mA 1, 2, 3 02, 03 0.50 For devic
44、e types 02,03 at VCC= 5.25 V, VIH= 2.0 V, VIL= 0.8 V IOL= +15 mA 1, 2, 3 02, 03 0.20 VCC= 5.5 V, VIH= 2.0 V, VIL= 0.8 V IOL= +88 mA 1, 2, 3 01 1.6 Input high leakage current IINHVCC= 5.5 V, VIH= 5.5 V, VIL= 0.0 V 1, 3 01 1.0 A 2 2.0VCC= 5.25 V, VIN= VCCor GND, 5.5 V, 1, 2, 3 02, 03 1.0 A Input low l
45、eakage current IINLVCC= 5.5 V, VIH= 5.5 V, VIL= 0.0 V 1, 3 01 1.0 A 2 2.0VCC= 5.25 V, VIN= VCCor GND, 5.5 V, 1, 2, 3 02, 03 1.0 A Quiescent supply current ICCVCC= 5.5 V, IOUT = 0.0 AVIH= 5.5 V, VIL= GND, RC1 = 0 V 1, 2, 3 01 500 A VCC= 5.5 V, IOUT = 0.0 AVIH= 5.5 V, VIL= GND, RC1 = 2.4 V 1, 2, 3 01
46、3.0 mA VCC= 5.5 V, IOUT = 0.0 AVIH= 5.5 V, VIL= GND, RC1 = 5.5 V 1, 2, 3 01 5.0 mA VCC= VIH= 5.25 V, VIL= GND. 1, 2, 3 02, 03 1.0 mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5
47、962-93196 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TC+125C 4.5 V VCC 5.5 V unless otherwise specified Group A subgroups Device type Limits 2/ Unit
48、Min Max Additional quiescent supply current ICCTVCC= 5.5 V, IOUT = 0.0 AVIH= 3.4 V (one input only) and all other inputs VIH= 5.5 V VIL= GND 1, 2, 3 01 1.6 mA VCC= 5.5 V, IOUT = 0.0 AVIH= 3.4 V (P/EN pin only) and all other inputs VIH= 5.5 V VIL= GND 1, 2, 3 01 3.0 mA VI= VCC 2.1 V, VCC= 5.25 V 4/ 1, 2, 3 02, 03 2.0 mA VCC= VIH= 5.25 V, VIL= GND. 1, 2, 3 02, 03 1.0 mA Input capacitance CINVCC= GND, TA .= +25C See 4.4.1c 4 01 6
