1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes IAW NOR 5962-R287-94 - jak 94-11-23 Monica L. Poelking B Update boilerplate to MIL-PRF-38535. Editorial changes throughout jak 00-11-21 Thomas M. Hess C Correct test condition for high level output voltage (VOH) and low level output volta
2、ge (VOL) in the table I. Update the boilerplate paragraphs to current requirements of MIL-PRF-38535 MAA 09-04-14 Thomas M. Hess REV SHEET REV C C C C C SHEET 15 16 17 18 19 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerb
3、y STANDARD MICROCIRCUIT DRAWING CHECKED BY Thanh V. Nguyen DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-04-27 MICR
4、OCIRCUIT, DIGITAL, ADVANCED BIPOLAR CMOS, OCTAL TRANSPARENT D-TYPE LATCH WITH THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-93218 SHEET 1 OF 19 DSCC FORM 2233 APR 97 5962-E219-09 Provided by IHSNot for ResaleNo reproduction or ne
5、tworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93218 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high rel
6、iability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The P
7、IN is as shown in the following example: 5962 - 93218 01 Q R A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA ma
8、rked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Devi
9、ce type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ABT373 Octal transparent D-type latch with 3-state outputs, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the pr
10、oduct assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 C
11、ase outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead f
12、inish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93218 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS
13、, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to +7.0 V dc 4/ DC output voltage range (VOUT) . -0.5 V dc to +5.5 V dc 4/ DC input clamp current (IIK) (VI
14、N 0.0 V). -18 mA DC output clamp current (IOK) (VOUT 0.0 V). -50 mA DC output current (IOL) (per output). +96 mA Storage temperature range (TSTG). -65C to +150C Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175
15、C Maximum power dissipation (PD) . 500 mW 1.4 Recommended operating conditions. 2/ 3/ 5/ Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT). +0.0 V dc to VCC Maximum low level input voltage (VIL) +0.8 V Minimum high level input vol
16、tage (VIH). +2.0 V Case operating temperature range (TC). -55C to +125C Maximum input rise and fall rate (t/V) 5 ns/V Maximum high level output current (IOH) -24 mA Maximum low level output current (IOL) +48 mA _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device.
17、 Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ The
18、input and output negative voltage ratings may be exceeded provided that the input and output clamp current ratings are observed. 5/ Unused inputs must be held high or low to prevent them from floating. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
19、STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93218 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of
20、 this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS M
21、IL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard For Microcircuit Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings (SMDs). MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available onl
22、ine at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing
23、 takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specifie
24、d herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN cla
25、ss level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline
26、s. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5
27、 Ground bounce test circuit and waveforms. The ground bounce test circuit and waveforms shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. Provided by IHSNot for ResaleNo reproduction or networkin
28、g permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93218 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified
29、 herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The el
30、ectrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
31、has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1
32、Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certific
33、ate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-
34、103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirem
35、ents of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notifi
36、cation of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agen
37、t, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by t
38、his drawing shall be in microcircuit group number 127 See MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93218 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LE
39、VEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test condition 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type VCCGroup A subgroups Min Max Unit VOH1For all inputs affecting output under
40、 test VIH= 2.0 V or VIL= 0.8 V IOH= -3 mA All 4.5 V 1, 2, 3 2.5 V VOH2For all inputs affecting output under test VIH= 2.0 V or VIL= 0.8 V IOH= -3 mA All 5.0 V 1, 2, 3 3.0 High level output voltage 3006 VOH3For all inputs affecting output under test VIH= 2.0 V or VIL= 0.8 V IOH= -24 mA All 4.5 V 1, 2
41、, 3 2.0 Low level output voltage 3007 VOLFor all inputs affecting output under test VIH= 2.0 V or VIL= 0.8 V IOL= +48 mA All 4.5 V 1, 2, 3 0.55 V Three-state output leakage current high 3021 IOZH4/ 5/ For control inputs affecting output under test, VIN= VIHor VIL VIH= 2.0 V VIL= 0.8 V VOUT= 2.7 V Al
42、l 5.5 V 1, 2, 3 10.0 A Three-state output leakage current low 3020 IOZL4/ 5/ For control inputs affecting output under test, VIN= VIHor VIL VIH= 2.0 V, VIL= 0.8 V VOUT= 0.5 V All 5.5 V 1, 2, 3 -10.0 A Negative input clamp voltage 3022 VIC-For input under test, IIN= -18 mA All 4.5 V 1, 2, 3 -1.2 V Of
43、f-state leakage current IOFFFor output under test VINor VOUT= 4.5 V All other pins at 0.0 V All 0.0 V 1 100.0 A High-state leakage current ICEXFor output under test VOUT= 5.5 V Outputs at high logic state All 5.5 V 1, 2, 3 50.0 A Input current high 3010 IIHFor input under test VIN= VCCAll 5.5 V 1, 2
44、, 3 +2.0 A Input current low 3009 IILFor input under test VIN= GND All 5.5 V 1, 2, 3 -2.0 A Output current 3011 IOUT 6/ VOUT= 2.5 V All 5.5 V 1, 2, 3 -50.0 -180.0 mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAND
45、ARD MICROCIRCUIT DRAWING SIZE A 5962-93218 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test condition 2/ -55C TC +125C 4.5 V V
46、CC 5.5 V unless otherwise specified Device type VCCGroup A subgroups Min Max Unit Quiescent supply current delta, TTL input levels 3005 ICC7/ For input under test, VIN= 3.4 V For all other inputs VIN= VCCor GND All 5.5 V 1, 2, 3 2.5 mA Quiescent supply current, output high 3005 ICCHVIN= VCCor GND IO
47、UT= 0.0 A All 5.5 V 1, 2, 3 250.0 A Quiescent supply current, output low 3005 ICCLVIN= VCCor GND IOUT= 0.0 A All 5.5 V 1, 2, 3 30.0 mA Quiescent supply current, output three-state 3005 ICCZVIN= VCCor GND IOUT= 0.0 A All 5.5 V 1, 2, 3 250.0 A Input capacitance 3012 CINSee 4.4.1c TC= +25C All 5.0 V 4
48、10.5 pF Output capacitance 3012 COUTSee 4.4.1c TC= +25C All 5.0 V 4 17.0 pF VOLP8/ All 5.0 V 4 800 mV Low level ground bounce noise VOLV8/ All 5.0 V 4 -1500 mV VOHP8/ All 5.0 V 4 1600 mV High level VCCbounce noise VOHV8/ VIH= 3.0 V , VIL= 0.0 V TA= +25C See figure 4 See 4.4.1d All 5.0 V 4 -800 mV See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93218 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OH