1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes IAW NOR 5962-R023-96 - jak. 95-12-26 Monica L. Poelking B Update boilerplate to MIL-PRF-38535. Editorial changes throughout jak. 00-11-20 Thomas M. Hess C Update boilerplate paragraphs to the current MIL-PRF-38535 requirements. - LTG 09-0
2、4-23 Thomas M. Hess REV SHET REV C C C SHEET 15 16 17 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby CHECKED BY Thanh V. Nguyen DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil APPROVED B
3、Y Monica L. Poelking STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-04-27 MICROCIRCUIT, DIGITAL, ADVANCED BIPOLAR CMOS, OCTAL TRANSPARENT D-TYPE LATCH WITH THREE-STATE OUTPUTS, TTL COMPATIBLE INPUT
4、S, MONOLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-93219 SHEET 1 OF 17 DSCC FORM 2233 APR 97 5962-E213-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93219 DEFENSE SUPPLY CENTER C
5、OLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes a
6、re available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 93219 01 Q R A Federal stock class designator RHA designator (see 1.2.1
7、) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class
8、 M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 5
9、4ABT573 Octal transparent D-type latch with three-state outputs, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the r
10、equirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive desi
11、gnator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Pr
12、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93219 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltag
13、e range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to +7.0 V dc 4/ DC output voltage range (VOUT) . -0.5 V dc to +5.5 V dc 4/ DC input clamp current (IIK) (VIN 0.0 V). -18 mA DC output clamp current (IOK) (VOUT 0.0 V). -50 mA DC output current (IOL) (per output). +96 mA Stor
14、age temperature range (TSTG). -65C to +150C Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C Maximum power dissipation (PD) . 500 mW 1.4 Recommended operating conditions. 2/ 3/ 5/ Supply voltage range (VCC) +
15、4.5 V dc to +5.5 V dc Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT). +0.0 V dc to VCC Maximum low level input voltage (VIL) 0.8 V Minimum high level input voltage (VIH). 2.0 V Case operating temperature range (TC). -55C to +125C Maximum input rise and fall rate (t/V) 5 ns/V M
16、aximum high level output current (IOH) -24 mA Maximum low level output current (IOL) 48 mA 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwis
17、e specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-183
18、5 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Stand
19、ardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, a
20、ll voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ The input and output negative voltage ratings may be exceeded provided that the input and output clamp current ratings are
21、 observed. 5/ Unused inputs must be held high or low to prevent them from floating. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93219 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVE
22、L C SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption
23、 has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not
24、affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and
25、 physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be
26、 as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce test circuit and waveforms. The ground bounce test circuit and waveforms shall be as specified on figure 4. 3
27、.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation pa
28、rameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The
29、part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product u
30、sing this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q
31、 and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer i
32、n order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA
33、 prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conforman
34、ce. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to D
35、SCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturer
36、s facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 127 (see MIL-PRF-38535,
37、appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93219 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance chara
38、cteristics. Test and MIL-STD-883 test method 1/ Symbol Test condition 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type VCCGroup A subgroups Limits 3/ Unit Min Max High level output voltage 3006 VOH1For all inputs affecting output under test VIN= 2.0 V or 0.8 V IOH= -3 mA All 4
39、.5 V 1, 2, 3 2.5 V VOH2For all inputs affecting output under test VIN= 2.0 V or 0.8 V IOH= -3 mA All 5.0 V 1, 2, 3 3.0 VOH3For all inputs affecting output under test VIN= 2.0 V or 0.8 V IOH= -24 mA All 4.5 V 1, 2, 3 2.0 Low level output voltage 3007 VOLFor all inputs affecting output under test VIN=
40、 2.0 V or 0.8 V IOL= 48 mA All 4.5 V 1, 2, 3 0.55 V Three-state output leakage current high 3021 IOZH4/ 5/ For control inputs affecting output under test VIN= VIHor VIL VIH= 2.0 V VIL= 0.8 V VOUT= 2.7 V All 5.5 V 1, 2, 3 10.0 A Three-state output leakage current low 3020 IOZL4/ 5/ For control inputs
41、 affecting output under test VIN= VIHor VIL VIH= 2.0 V VIL= 0.8 V VOUT= 0.5 V All 5.5 V 1, 2, 3 -10.0 A Negative input clamp voltage 3022 VIC-For input under test IIN= -18 mA All 4.5 V 1, 2, 3 -1.2 V Off-state leakage current IOFFFor output under test VINor VOUT= 4.5 V All other pins at 0.0 V All 0.
42、0 V 1 100.0 A High-state leakage current ICEXFor output under test VOUT= 5.5 V Outputs at high logic state All 5.5 V 1, 2, 3 50.0 A Input current high 3010 IIHFor input under test VIN= VCCAll 5.5 V 1, 2, 3 +2.0 A Input current low 3009 IILFor input under test VIN= GND All 5.5 V 1, 2, 3 -2.0 A Output
43、 current 3011 IOUT 6/ VOUT= 2.5 V All 5.5 V 1, 2, 3 -50.0 -180.0 mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93219 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-399
44、0 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test condition 2/ -55C TC +125C 4.5 V VCC 5.5 V unless otherwise specified Device type VCCGroup A subgroups Limits 3/ Unit Min Max Quiescent supply
45、 current delta TTL input levels 3005 ICC7/ For input under test VIN= 3.4 V For all other inputs VIN= VCCor GND All 5.5 V 1, 2, 3 2.5 mA Quiescent supply current, output high 3005 ICCHVIN= VCCor GND IOUT= 0.0 A All 5.5 V 1, 2, 3 250.0 A Quiescent supply current, output low 3005 ICCLVIN= VCCor GND IOU
46、T= 0.0 A All 5.5 V 1, 2, 3 30.0 mA Quiescent supply current, output three-state 3005 ICCZVIN= VCCor GND IOUT= 0.0 A All 5.5 V 1, 2, 3 250.0 A Input capacitance 3012 CINSee 4.4.1c TC= +25C All 5.0 V 4 8.5 pF Output capacitance 3012 COUTSee 4.4.1c TC= +25C All 5.0 V 4 17.0 pF Low level ground bounce n
47、oise VOLP8/ All 5.0 V 4 900 mV Low level ground bounce noise VOLV8/ All 5.0 V 4 -1700 mV High level VCCbounce noise VOHP8/ All 5.0 V 4 1300 mV High level VCCbounce noise VOHV8/ VIH= 3.0 V VIL= 0.0 V TA= +25C See figure 4 See 4.4.1d All 5.0 V 4 -600 mV All 4.5 V 7, 8 L H Functional test 3014 9/ VIL=
48、0.8 V VIH= 2.0 V Verify output VOUT See 4.4.1b All 5.5 V 7, 8 L H 5.0 V 9 1.5 5.4 tPLH110/ All 4.5 V and 5.5 V 10, 11 1.0 6.4 ns 5.0 V 9 1.5 5.7 Propagation delay time, mD input to mQ output 3003 tPHL110/ CL= 50 pF minimum RL= 500 See figure 5 All 4.5 V and 5.5 V 10, 11 1.5 6.7 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93219 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I
