1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change to the supply current test, ICC, in table I. Update boilerplate. - rrp 99-11-16 R. MONNIN B Add radiation hardness requirements. Add case outline D. Add table IIB. - rrp 00-05-05 R. MONNIN C Add footnote to the supply voltage test in secti
2、on 1.3. Add footnote to the supply current and power supply rejection ratio test in table I. Update boilerplate. rrp 01-10-17 R. MONNIN D Change to the post irradiation test limits in table I for IIO, IIB, AVO, and ICC. Removed accelerated aging and dose rate burnout provisions in section 4. rrp 01-
3、11-15 R. MONNIN E Added subgroup 4 to table IIA under group E end-point for device class V. gt 03-03-11 R. MONNIN F Drawing updated to reflect current requirements. - rrp 05-09-07 R. MONNIN G Delete footnote 2/ from section 1.3. Delete footnote 5/ from Table I. These footnotes were incorrectly added
4、 under revision C. - ro 10-04-22 C. SAFFLE REV SHEET REV SHEET REV STATUS REV G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 PMIC N/A PREPARED BY RICK C. OFFICER DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING
5、IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH R. PITHADIA APPROVED BY MICHAEL A. FRYE MICROCIRCUIT, LINEAR, RADIATION HARDENED, PRECISION, HIGH SPEED, QUAD OPERATIONAL AMPLIFIER, MONOLITHIC SILICON DRAWING APPROVAL DATE 94-03-02 AMSC N/A REVISION
6、 LEVEL G SIZE A CAGE CODE 67268 5962-93258 SHEET 1 OF 11 DSCC FORM 2233 APR 97 5962-E240-10 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93258 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVIS
7、ION LEVEL G SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the P
8、art or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 R 93258 01 V C A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class
9、designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PR
10、F-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 OP467 High speed, quad, operational am
11、plifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in a
12、ccordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1
13、-F14or CDFP2-F14 14 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without licen
14、se from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93258 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage (VCC) . 18 V Differential input voltage 2/ . 26 V Input voltage 2/ . 18 V Output sho
15、rt-circuit duration Limited Storage temperature range -65C to +175C Lead temperature (soldering, 60 seconds) +300C Junction temperature (TJ) -65C to +175C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case C . 94C/W Case D . 140C/W Case 2 78
16、C/W 1.4 Recommended operating conditions. Supply voltage (VCC) . 15 V Ambient operating temperature range (TA) . -55C to +125C 1.5 Radiation features. Maximum total dose available (dose rate = 50 300 rads(Si)/s) . 100 krads 3/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and hand
17、books. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits,
18、 Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Sta
19、ndard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 1/ Stresses above the absolute maximum rating may cause permanent
20、damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ For supply voltages less than 18 V, the absolute maximum input voltage is equal to the supply voltage. 3/ These parts may be dose rate sensitive in a space environment and may demonstrat
21、e enhanced low dose rate effects. Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883, method 1019, condition A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRA
22、WING SIZE A 5962-93258 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in t
23、his document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the
24、device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as speci
25、fied herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be i
26、n accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits.
27、 Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups
28、 specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space
29、 limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MI
30、L-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For dev
31、ice classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approve
32、d source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or f
33、or device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delive
34、red to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For d
35、evice class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Devi
36、ce class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93258 DEFENSE SUPPLY CENTER COLUMBUS COLUMB
37、US, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 3/ Unit Min Max Input offset voltage VIOVCC= 5 V 1 01 0.5 mV 2, 3 1.0 VCC= 15
38、 V 1 0.5 2, 3 1.0 M,D,P,L,R 1 1.5 Input offset current IIOVCC= 5 V, VCM= 0 V 1 01 100 nA 2, 3 150 VCC= 15 V, VCM= 0 V 1 100 2, 3 150 M,D,P,L,R 1 300 Input bias current IIBVCC= 5 V, VCM= 0 V 1 01 600 nA 2, 3 700 VCC= 15 V, VCM= 0 V 1 600 2, 3 700 M,D,P,L,R 1 2000 Common mode rejection ratio CMRR VCC=
39、 5 V, 4/ VCM= 2 V 1, 2, 3 01 76 dB VCC= 15 V, 4/ VCM= 12 V 80 Large signal voltage gain AVOVCC= 5 V, RL= 2 k 4 01 80 dB 5, 6 74 VCC= 15 V, RL= 2 k 4 83 5, 6 77.5 M,D,P,L,R 4 63 Output voltage swing VOUTVCC= 5 V, RL= 2 k 4/ 4, 5, 6 01 3.0 V VCC= 15 V, RL= 2 k 4/ 4 13 5, 6 12.9 See footnotes at end of
40、 table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93258 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteri
41、stics - Continued Test Symbol Conditions 1/ 2/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 3/ Unit Min Max Supply current ICCVCC= 5 V, VOUT= 0 V 1 01 10 mA 2, 3 12 VCC= 15 V, VOUT= 0 V 1 10 2, 3 13 M,D,P,L,R 1 11 Power supply rejection ratio PSRR VCC= 4.5 V to 5.5 V
42、 4/ 1 01 92 dB 2, 3 83 VCC= 4.5 V to 18 V 4/ 1 96 2, 3 86 Input offset voltage drift TCVIOVCC= 15 V, 4/ TA= +125C, -55C 8 01 5 V/C Gain bandwidth product GBWP VCC= 5 V, AV= +1, 4/ CL= 30 pF, TA= +25C 7 01 16 MHz VCC= 15 V, AV= +1, 4/ CL= 30 pF, TA= +25C 21 Slew rate SR VCC= 5 V, 4/ VIN= 5 V step, AV
43、= +1, RL= 2 k, CL= 30 pF, TA= +25C 7 01 85 V/s VCC= 15 V, AV= +1, 4/ VIN= 10 V step, RL= 2 k, CL= 30 pF, TA= +25C 125 Settling time tSVCC= 15 V, AV= +1, 4/ VIN= 10 V step to 0.01% of the final value, TA= +25C 9 01 300 ns 1/ RHA devices supplied to this drawing will meet all levels M, D, P, L, R of i
44、rradiation. However, this device is only tested at the R level. Pre and Post irradiation values are identical unless otherwise specified in table I. When performing post irradiation electrical measurements for any RHA level, TA= +25C. 2/ These parts may be dose rate sensitive in a space environment
45、and may demonstrate enhanced low dose rate effects. Radiation end point limits for the noted parameters are guaranteed only for the conditions specified in MIL-STD-883, method 1019, condition A. 3/ The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only
46、. Negative current shall be defined as conventional current flow out of a device terminal. 4/ This parameter is not tested post-irradiation. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93258 DEFENSE SUPPL
47、Y CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outlines C and D 2 Terminal number Terminal symbol 1 OUTPUT A NC 2 -INPUT A OUTPUT A 3 +INPUT A -INPUT A 4 +VCC+INPUT A 5 +INPUT B NC 6 -INPUT B +VCC7 OUTPUT B NC 8 OUTPUT C +INPUT B 9 -INP
48、UT C -INPUT B 10 +INPUT C OUTPUT B 11 -VCCNC 12 +INPUT D OUTPUT C 13 -INPUT D -INPUT C 14 OUTPUT D +INPUT C 15 - NC 16 - -VCC17 - NC 18 - +INPUT D 19 - -INPUT D 20 - OUTPUT D NC = No connection FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93258 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHE
