1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Technical and editorial changes throughout. 94-05-24 M. A. FRYE B Add device type 03. Technical and editorial changes throughout. 95-08-16 M. A. FRYE C TABLE I. VREFshort circuit current test. For device types 02 and 03, delet
2、e the max limit of “45 mA” and substitute “60 mA”. Changes in accordance with NOR 5962-R342-97. 97-06-10 R. MONNIN D Change to VINRin table I. Update boilerplate. rrp 00-08-09 R. MONNIN E Change to ENATRin table I. Update boilerplate. -rrp 01-04-02 R. MONNIN F Changes to VTONand VTOFFtests in table
3、I. Add VCCHtest to table I. Drawing updated to reflect current requirements. -rrp 06-02-17 R. MONNIN G Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 12-04-03 C. SAFFLE REV SHEET REV SHEET REV STATUS REV G G G G G G G G G G G G G G OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 1
4、2 13 14 PMIC N/A PREPARED BY MARCIA KELLEHER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY SANDRA B. ROONEY APPROVED BY MICHAEL
5、A. FRYE MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, HIGH POWER FACTOR, MONOLITHIC SILICON DRAWING APPROVAL DATE 94-03-08 AMSC N/A REVISION LEVEL G SIZE A CAGE CODE 67268 5962-93261 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E297-12 Provided by IHSNot for ResaleNo reproduction or networking permitted with
6、out license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93261 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M
7、) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following
8、example: 5962 - 93261 01 Q E X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38
9、535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) i
10、dentify the circuit function as follows: Device type Generic number Circuit function 01 UC1854 Voltage preregulator, high power factor 02 UC1854B Voltage preregulator, high power factor 03 UC1854A Voltage preregulator, high power factor 1.2.3 Device class designator. The device class designator is a
11、 single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and quali
12、fication to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish
13、 is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93261 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3
14、990 REVISION LEVEL G SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage (VCC): Device type 01 . 35 V dc Device types 02 and 03 22 V dc GTDRV current, continuous . 0.5 A GTDRV current, 50 percent duty cycle 1.5 A Input voltage, VSENSE, VRMS. 11 V dc Input voltage, ISE
15、NSE, MULTOUT11 V dc Input voltage, PKLMT 5 V dc Input current, RSET, IAC, ENA, PKLMT 10 mA Power dissipation, TA= +25C (PD) 1 W 4/ Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA) . 80C/W Storage temperature range -65C to +150C Lead temperature
16、(soldering, 10 seconds) +300C Junction temperature (TJ) +150C 1.4 Recommended operating conditions. Supply voltage . 18 V dc Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards
17、, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DE
18、PARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these
19、 documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited her
20、ein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum lev
21、els may degrade performance and affect reliability. 2/ All voltages with respect to GND. 3/ All currents are positive into the specified terminal. 4/ Derate 8 mW/C for TA +25C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRA
22、WING SIZE A 5962-93261 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in th
23、e device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as spe
24、cified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be
25、 in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Block diagrams. The block diagrams shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise spec
26、ified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II
27、. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manuf
28、acturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A
29、. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a
30、certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in M
31、IL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for dev
32、ice class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to
33、 this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device cl
34、ass M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcir
35、cuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 52 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 59
36、62-93261 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Overall section. Supply current
37、, Off ICCOFFENA = 0 V 1,2,3 01 2.0 mA CAOUT= 0 V, VAOUT= 0 V, VCC= UVLO 0.3 V 02, 03 0.4 Supply current, On ICCON1,2,3 01 16 mA 02, 03 18 VCCturn-on threshold VTON1,2,3 01 14.5 17.5 V 02 8 11.2 03 15 17.5 VCCturn-off threshold VTOFF1,2,3 01 9 11 V 02 7.8 11 03 9 12 VCChysteresis VCCH1, 2, 3 02 0.1 0
38、.5 V (VTON VTOFF) 03 5 7 ENA threshold, rising ENATR1,2,3 01 2.4 2.7 V 02, 03 2.35 2.8 ENA threshold hysteresis ENATH1,2,3 01 0.2 0.3 V VFAULT= 2.5 V 02, 03 0.35 0.6 ENA input current ENAIINENA = 0 V 1,2,3 All -5.0 +5.0 A VRMSinput current RMSINVRMS= 5 V 1,2,3 01 -1.0 +1.0 A VCCclamp voltage VCMPI (
39、VCC) = ICC(ON)+ 5 mA 1,2,3 02, 03 18 22 V Voltage amplifier section. Voltage amp offset voltage VAOVAOUT= 5.0 V 1,2,3 01 -8 +8 mV Voltage amp input voltage VIA1,2,3 02, 03 2.9 3.1 V Voltage amp VOUThigh VOAHILOAD= -500 A 1,2,3 02, 03 4 V Voltage amp VOUTlow VOALILOAD= 500 A 1,2,3 02,03 0.5 V VSENSEb
40、ias current IBVSENSE= 0 V 1,2,3 All -500 500 nA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93261 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 6 DS
41、CC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Voltage amplifier section continued. Voltage amp output swing VAOS1,2,3 01 0.5 to 5 V Voltage amp gain AV
42、A1,2,3 All 70 dB Voltage amp short circuit current IASCVAOUT= 0 V 1,2,3 01 5 36 mA 02, 03 3.5 SS current ISSSS = 2.5 V 1,2,3 01 6 20 A 02, 03 10 24 Current amplifier section. Current amp input offset voltage VIAOVCM= 0 V 1,2,3 01 -4 +4 mV 02, 03 -4 0 Current amp output voltage high IOAHILOAD= -500 A
43、 1,2,3 02, 03 6 V Voltage amp output voltage low IOALILOAD= 500 A 1,2,3 02, 03 0.5 V ISENSEbias current IBVCM= 0 V 1,2,3 All -500 500 nA Current amp gain AIAVCM= 0 V, VOUT= 2 to 6 V 1,2,3 All 80 dB Current amp output voltage swing VAOS1,2,3 01 0.5 to 16 V Current amp short circuit current IASCCAOUT=
44、 0 V 1,2,3 01 5 36 mA 02, 03 3.5 Current amp input voltage range ISENSE, VINR1,2,3 01 -0.1 to 1.0 V MULTOUT02, 03 -0.1 to 5.0 Reference section. Reference output voltage VOUTR IREF= 0 mA 1 All 7.4 7.6 V 2,3 7.35 7.65 VREFload regulation VRLOAD-10 mA IREF 0 mA 1,2,3 01 -15 +15 mV 02, 03 0 +20 See foo
45、tnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93261 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL G SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance cha
46、racteristics Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Rerence section continued. VREFshort circuit current ISCVREF= 0 V 1,2,3 01 12 50 mA 02, 03 25 60 VREFline regulation VRLINE15 V VCC 35 V 1,2,3 01 -10 +10 mV 12
47、V VCC 18 V 02,03 0 +25 Current limit section. PKLMT offset voltage VOPKLMT1,2,3 01 -10 +10 mV 02, 03 -15 +15 PKLMT input current IIPKLMTPKLMT = -0.1 V 1,2,3 All -200 A Gate driver section. Maximum GTDRV output voltage VOGTDRV0 mA load on GTDRV, 18 V VCC 35 V 1,2,3 01 13 18 V GTDRV output voltage hig
48、h VOHTDRV-200 mA load on GTDRV, VCC= 15 V 1,2,3 All 12 V GTDRV output voltage low, OFF VOLDRV150 mA load on GTDRV, VCC= 0 V 1,2,3 All 1.5 V GTDRV output voltage low VOLDRV2200 mA load on GTDRV 1,2,3 All 2.2 V GTDRV output voltage low VOLDRV310 mA load on GTDRV 1,2,3 02, 03 500 mV Multiplier section. Multiplier output current full scale IMOFSVRMS= 1 V, RSET= 10 k, 1,2,3 01 -220 -180 A IAC = 100 A 02, 03 -220 -170 Multiplier output current zero IMOZIAC = 0 A, RSET= 15 k 1,2,3 All -2.0 +2.0 A Multiplier maximum output current IMMO
