1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R117-96. 96-04-22 K. A. Cottongim B Add case outline Y. Update document to MIL-PRF-38534 requirements. 97-07-14 K. A. Cottongim C Figure 2, terminal connections, correct terminal symbol for pins 8, 28, 29, 30,
2、31, 48, and 54, for all device types. Table II, correct subgroups for interim electrical parameters. Update drawing boilerplate. 02-08-02 Raymond Monnin D Rewrite paragraphs 4.2.a.2. and 4.3.3.b.2 to add TC. 04-07-16 Raymond Monnin E Updated drawing paragraphs. -sld 12-09-12 Charles F. Saffle REV SH
3、EET REV SHEET REV STATUS REV E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C. Jones THIS DRAWING IS AVAILABLE FOR US
4、E BY ALL DEPARTMENTS APPROVED BY Kendall A. Cottongim MICROCIRCUIT, HYBRID, LINEAR, 90-VOLT, SYNCHRO TO DIGITAL CONVERTER AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-07-06 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-94547 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E270
5、-12 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94547 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product
6、 assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN. 1.2 PIN. The PIN sh
7、all be as shown in the following example: 5962 - 94547 01 H X A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 Radiation hardness assurance (RHA) designato
8、r. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function Frequ
9、ency Accuracy 1 LSB 01 SD-14622DX-112, SD-14622FX-112 90 V S/D converter 400 Hz 4 min 02 SD-14624DX-112, SD-14624FX-112 90 V S/D converter 60 Hz 4 min 03 SD-14622DX-114, SD-14622FX-114 90 V S/D converter 400 Hz 2 min 04 SD-14624DX-114, SD-14624FX-114 90 V S/D converter 60 Hz 2 min 1.2.3 Device class
10、 designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance lev
11、els are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applications. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required
12、. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limited temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspection
13、s (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of that class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensur
14、e that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufacturers internal, QML certified flow. This product may have a limited temperature range. Provided by IHSNot for ResaleNo reproduction or networkin
15、g permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94547 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descript
16、ive designator Terminals Package style X See figure 1 54 Dual-in-line Y See figure 1 54 Flat package 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Positive supply voltage (VCC) . +7.0 V dc Reference input voltage . 130 V rms Digital input
17、 voltage range . -0.3 V dc to +7.0 V dc Power dissipation, TA= +125 C (PD) . 350 mW Storage temperature range -65 C to +150 C Lead temperature (soldering, 10 seconds) +300 C Thermal resistance junction-to-case (qJC) 8.0 C/W Thermal resistance junction-to-ambient (qJA) . 20 C/W 1.4 Recommended operat
18、ing conditions. Positive supply voltage (VCC) . +4.75 V dc to +5.25 V dc Reference input voltage range . 2.0 V rms to 35 V rms Reference input carrier frequency range: Device types 01 and 03 360 Hz to 5000 Hz Device types 02 and 04 47 Hz to 1000 Hz Signal input voltage range . 81 V rms to 99 V rms A
19、mbient operating temperature range (TA) -55 C to +125 C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these do
20、cuments are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component C
21、ase Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenu
22、e, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specif
23、ic exemption has been obtained. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from
24、IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94547 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with
25、MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated for the applicable device class. The manufacturer may eliminate, modify, or optimize the tests and inspections her
26、ein, however, the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form, fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensio
27、ns. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Blo
28、ck diagram. The block diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating temperature range. 3.4 Electrical t
29、est requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with the PIN listed in
30、1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) from the initial quality confor
31、mance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be made availab
32、le to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affir
33、m that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. 4. VERIFICATION 4.1 Sampling and insp
34、ection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. 4.2 Screening. Screening shall be in accordan
35、ce with MIL-PRF-38534. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to either DLA Land and Marit
36、ime -VA or the acquiring activity upon request. Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1015 of MIL-STD-883. (2) TAor TCas specified in accordance with table I of method 1015 of MIL-STD-
37、883. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
38、,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94547 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55 C TA +125 C VCC= +5 V dc, unless otherwise specified Group A subgroups Device
39、 type Limits Unit Min Max Resolution control 1/ RC A = B = 0.8 V 7,8A,8B All 10 10 Bits A = 2.0 V, B = 0.8 V 12 12 A = 0.8 V, B = 2.0 V 14 14 A = B = 2.0 V 16 16 Accuracy repeatability AR 2/ 3/ 7,8A,8B All -1.0 +1.0 LSB Accuracy differential AD 2/ 3/ 7,8A,8B All -1.0 +1.0 LSB Output accuracy AOUT 2/
40、 7,8A,8B 01,02 -13 +13 LSB 03,04 -7 +7 Reference input voltage range 3/ VIN14,5,6 All 10 130 V rms Reference input impedance 3/ ZIN1Single ended 4,5,6 All 270 kW Differential 540 Reference input common mode range 3/ VCM14,5,6 All -200 +200 V pk Signal input common mode range 3/ VCM24,5,6 All -180 +1
41、80 V pk Signal input impedance 3/ ZIN2 Line-to-line 4,5,6 All 123 kW Line-to-ground 80 Digital output low voltage VOLIOL= -1.6 mA 1,2,3 All 0.4 V Digital output high voltage VOHIOH= 0.4 mA 1,2,3 All 2.8 V Output leakage current IOZ1,2,3 All -40 +40 mA See footnotes at end of table. Provided by IHSNo
42、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94547 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Con
43、ditions -55 C TA +125 C VCC= +5 V dc, unless otherwise specified Group A subgroups Device type Limits Unit Min Max Digital input high voltage 1/ VIHDigital inputs A, B, INH, EL, and EM. VIN= 2.0 V 1,2,3 All pass/ fail Digital input low voltage 1/ VILDigital inputs A, B, INH, EL, and EM. VIN= 0.8 V 1
44、,2,3 All pass/ fail Digital input current 1/ IINInternal pull-up 4,5,6 All 10 mA Inhibit voltage 1/ VINHNo digital angles change while INH is logic 0 and analog input is rotating 7,8A,8B All 0.8 V Enable voltage 1/ VEEM controls output bits 1 through 8 and EL controls output bits 9 through 16. 7,8A,
45、8B All 0.8 V Disable voltage 1/ (high impedance) VDEM controls output bits 1 through 8 and EL controls output bits 9 through 16. 7,8A,8B All 2.0 V Positive supply voltage ICCVCC= +5.25 V 1,2,3 All +68 mA Analog velocity output voltage VOUT4/ 7,8A,8B All 3.24 4.00 V Bandwidth 1/ BW 7,8A,8B 01,02 39 7
46、2 Hz 03,04 10 20 1/ These parameters are tested on a go-no-go basis only or in conjunction with other measured parameters and are not directly testable. 2/ Output accuracy is measured at angles from 0 to 180 , in 15 increments, and at 225 , 270 , and 315 . 3/ Parameters shall be tested as part of de
47、vice initial characterization and after design and process changes. Parameters shall be guaranteed to the limits specified in table I for all lots not specifically tested. 4/ Analog output voltage is tested at 2 rps for device types 01 and 03, and 0.25 rps for device types 02 and 04. Provided by IHS
48、Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94547 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 Case outline X. Symbol Millimeters Inches Minimum Maximum Minimum Maximum A1 5.33 .210 b 0.41 0.51 .016 .020 b1 1.14 1.40 .045 .055 D 38.10 1.500 D1 32.89 33.15 1.295 1.305 D2 30.35 30.61 1.195 1.205 D3 2.41
