1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change VOHmaximum limit in table I from 3.4 V to 3.5 V. Update boilerplate to MIL-PRF-38535 requirements. - CFS 02-02-06 Thomas M. Hess REV SHET REV A A A A SHEET 15 16 17 18 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6
2、7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Thomas M. Hess DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Thomas M. Hess COLUMBUS, OHIO 43216 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, CMOS,
3、 8-BIT TTL/BTL REGISTERED TRANSCEIVER, MONOLITHIC AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-09-07 SILICON AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-94574 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E245-02 DISTRIBUTION STATEMENT A. Approved for public release; distr
4、ibution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94574 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This draw
5、ing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation
6、Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 94574 01 M X X Federal stock class designator RHA designator (see 1.2.1) Devicetype (see 1.2.2) Device class designator Caseoutline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3
7、) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropr
8、iate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54FB2033 8-bit TTL/BTL registered transceiver 1.2.3 Device class designator. The device class designator is a
9、single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualif
10、ication to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDFP1-F56 56 Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V
11、or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94574 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1
12、.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) -0.5 V to +7 V Input voltage range (VI, except B port) -1.2 V to 7 V (VI, B port) . -1.2 V to 3.5 V Input current range, (except B port). -40 mA to 5 mA Voltage range applied to any B output in the disabled or power-off state -0.5 V to 3.5 V
13、 Voltage range applied to any output in the high state (A port) -0.5 V to VCCCurrent applied to any single output in the low state A port. 48 mA B port. 200 mA Maximum power dissipation (PD) (TA= 55C, still air) 1.7 W (TA= 25C) 1.1 W Storage temperature range . -65C to +150C 1.4 Recommended operatin
14、g conditions. 2/ Supply voltage (VCC, BG VCC) 4.75 V VCC 5.25 V Supply voltage (bias VCC) 4.5 V VCC 5.5 V Input transition rise or fall rate (t/v) except B port . 10 ns/V High level input voltage (VIH) B port. 1.62 V VIH 2.3 V except B port . 2 V min Low level input voltage (VIL) B port. 0.75 V VIL
15、1.47 V except B port . 0.8 V max High level output current (IOH) AO port -3.0 mA max Low level output current (IOL) AO port 24 mA max B port. 100 mA max Ambient operating temperature. -55C to +125C _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended ope
16、ration at the maximum levels may degrade performance and affect reliability. 2/ Unused or floating pins (input or I/O) must be held high or low. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94574 DEFENSE S
17、UPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless othe
18、rwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General
19、Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawi
20、ngs. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and
21、the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shal
22、l be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in acco
23、rdance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendi
24、x A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Block diagram. The block diagram shall be as specified on figure 2. 3.2.4 Truth table. The t
25、ruth table shall be as specified on figure 3. 3.2.5 Timing waveforms and test circuit. The timing waveforms and test circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performan
26、ce characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94574 DEFENSE SUPPL
27、Y CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be ma
28、rked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA
29、 product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device
30、 classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manu
31、facturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted
32、to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of
33、 conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notific
34、ation to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to
35、 review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number
36、127 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94574 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Elec
37、trical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 3/ Unit 4.75 V VCC 5.25 V 1/ Min Max Input clamp voltage VIKVCC= 4.75 V, II= -18 mA 1, 2, 3 All -1.2 V Output voltage high AO port VOHVCC= 4.75 V to 5.25 V IOH= -1
38、0 A 1, 2, 3 All VCC 1.0 V VCC= 4.75 V, IOH= -3 mA 2.5 3.5 Output voltage high AO port VOHVCC= 4.75 V, IOH= -32 mA 1, 2, 3 All 2.0 V VCC= 4.75 V, IOL= 20 mA 0.5 Output voltage low AO port VOLVCC= 4.75 V, IOL= 55 mA 1, 2, 3 All 0.8 V VCC= 4.75 V, IOL= 100 mA 0.75 1.1 Output voltage low B port VOLVCC=
39、4.75 V, IOL= 4 mA 1, 2, 3 All 0.5 V Input current except B port IIVCC= 0 V, VI= 5.25 V 1, 2, 3 All 100 A Input current high except B port 2/ IIHVCC= 5.25 V, VI= 2.7 V 1, 2, 3 All 50 A Input current high B port IIHVCC= 0 to 5.25 V, VI= 2.1 V 1, 2, 3 All 100 A Input current low except B port IILVCC= 5
40、.25 V, VI= 0.5 V 1, 2, 3 All -50 A Input current low B port 2/ IILVCC= 5.25 V, VI= 0.75 V 1, 2, 3 All -100 A Output current high B port IOHVCC= 0 to 5.25 V, VI= 2.1 V 1, 2, 3 All 100 A Output current high tristate, AO port IOZHVCC= 5.25 V, VO= 2.7 V 1, 2, 3 All 50 A Output current low tristate, AO p
41、ort IOZLVCC= 5.25 V, VO= 0.5 V 1, 2, 3 All -50 A Output short circuit current, AO port 3/ IOSVCC= 5.25 V, VO= 0 V 1, 2, 3 All -40 -150 mA Power supply current All outputs on ICCVCC= 5.25 V, IO= 0 A 1, 2, 3 All 90 mA Input capacitance All port and control inputs CIVI= VCCor GND See 4.4.1c 4 All 9.5 p
42、F Output capacitance AO port COVO= VCCor GND See 4.4.1c 4 All 9.0 pF VCC= 0 to 4.75 V 8 Input/Output capacitance B port CI/OVCC= 4.75 V to 5.25 V 4 All 8 pF Functional test See 4.4.1b 7, 8 All VCC= 5 V, TA= 25C See figure 3 9 Clock frequency fCLOCKVCC= 4.75 V to 5.25 V See figure 3 10, 11 All 0 150
43、MHz See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94574 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Table I. Electr
44、ical performance characteristics - Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 3/ Unit 4.75 V VCC 5.25 V 1/ Min Max VCC= 5.0 V 9 3.9 Pulse duration, CLKAB/LEAB or CLKBA/LEBA tWSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 4.3 ns VCC=
45、5.0 V 9 2.9 Setup time, data before CLKAB/LEAB or CLKBA/LEBA tSUSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 3.3 ns VCC= 5.0 V 9 1.0 Hold time, data after CLKAB/LEAB or CLKBA/LEBA tHSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 1.3 ns VCC= 5.0 V 9 Maximum frequency fMAXSee figure 3 VCC= 4.75 V, 5.25 V
46、10, 11 All 150 MHz VCC= 5.0 V 9 1.7 4.6 Propagation delay AI (thru mode) to B tPLHSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 1.2 7.5 ns VCC= 5.0 V 9 1.3 4.3 Propagation delay AI (thru mode) to B tPHLSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 1.0 5.5 ns VCC= 5.0 V 9 2.5 5.9 Propagation delay B (thr
47、u mode) to AO tPLHSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 1.4 7.6 ns VCC= 5.0 V 9 2.7 5.7 Propagation delay B (thru mode) to AO tPHLSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 1.6 7.8 ns VCC= 5.0 V 9 1.7 4.6 Propagation delay AI (transparent) to B tPLHSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All
48、1.2 8.7 ns VCC= 5.0 V 9 1.3 4.3 Propagation delay AI (transparent) to B tPHLSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 1.0 5.9 ns VCC= 5.0 V 9 2.5 5.8 Propagation delay B (transparent) to AO tPLHSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 1.5 7.8 ns VCC= 5.0 V 9 2.7 5.7 Propagation delay B (transpa
49、rent) to AO tPHLSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 1.6 8.0 ns VCC= 5.0 V 9 1.6 4.7 Propagation delay OEB to B tPLHSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 1.1 6.6 ns VCC= 5.0 V 9 1.2 4.1 Propagation delay OEB to B tPHLSee figure 3 VCC= 4.75 V, 5.25 V 10, 11 All 0.4 5.4 ns See footnotes at end of table. Provided by IHSNo
