1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Under figure 1, case outline E terminal connections; for pin 5, delete “-INPUT” and substitute “+INPUT”; for pin 6, delete “+INPUT” and substitute “-INPUT”. In accordance with N.O.R. 5962-R226-94. 94-07-12 M. A. FRYE B Sheet 6: TABLE I. Amplifier
2、 gain test. Delete the max limit of “3.3 V/V” and substitute “3.35 V/V”. Sheet 7: TABLE I. Power supply rejection ratio test. Delete the min limit of “60 dB” and substitute “56 dB”. Sheet 8: TABLE I. VCCshunt voltage test. Delete the max limit of “16.5 V” and substitute “17.5 V”. In accordance with
3、N.O.R. 5962-R057-97. 97-03-07 R. MONNIN C Make change to delay to outputs test as specified under the shutdown terminal section of TABLE I. Redrawn. ro 97-07-16 R. MONNIN D Add case outline 2. Make changes to 1.2.4, 1.3, and FIGURE 1. ro 97-10-22 R. MONNIN E Replaced reference to MIL-STD-973 with re
4、ference to MIL-PRF-38535. Drawing updated to reflect current requirements. - gt 04-03-31 R. MONNIN F Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 11-12-02 C. SAFFLE REV SHET REV SHET REV STATUS REV F F F F F F F F F F F F F F OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13
5、 14 PMIC N/A PREPARED BY RICK C. OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH R. PITHADIA APPROVED BY MICHAEL A.
6、 FRYE MICROCIRCUIT, LINEAR, LOW POWER, DUAL OUTPUT, PULSE WIDTH MODULATOR, MONOLITHIC SILICON DRAWING APPROVAL DATE 94-04-11 AMSC N/A REVISION LEVEL F SIZE A CAGE CODE 67268 5962-94575 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E316-11 Provided by IHSNot for ResaleNo reproduction or networking permitt
7、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94575 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes
8、Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the fol
9、lowing example: 5962 - 94575 01 M E A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PR
10、F-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(
11、s) identify the circuit function as follows: Device type Generic number Circuit function 01 UCC1806 Dual output, pulse width modulator 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements do
12、cumentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835
13、 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device c
14、lass M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94575 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ Supply voltage
15、(low impedance) . +15.0 V Supply current (high impedance) +25.0 mA OUTPUT supply voltage . +18 V OUTPUT current, continuous source or sink . 200 mA OUTPUT current, gate drive . 500 mA Analog input voltage . -0.3 V to +VIN+ 0.3 V SYNC output current . 30 mA Error amplifier output current (COMP pin) .
16、 +10 mA is self limiting Power dissipation (PD) at TA +25C 1.0 W Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Thermal resistance, junction-to-ambient (JA): Case E . 110C/W Case 2 . 70C/W 1.4 Reco
17、mmended operating conditions. Supply voltage +12.0 V Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified here
18、in. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microci
19、rcuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearc
20、h/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document
21、, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ All voltages are
22、respect to ground. All currents are positive into the specified terminal. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94575 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 4 DSCC FO
23、RM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affec
24、t the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and phys
25、ical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as s
26、pecified on figure 1. 3.2.3 Logic diagram. The logic diagram shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as s
27、pecified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked
28、 with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA d
29、esignator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or
30、“Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the re
31、quirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to
32、listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A cert
33、ificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land an
34、d Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity re
35、tain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcir
36、cuit group number 110 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94575 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 5 DSCC FORM 2234 APR 97 TABL
37、E I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Reference section Output voltage VOUTIOUT= 0.2 mA, TA= +25C 1 01 5.02 5.17 V Load regulation VLDIOUT= 0.2 mA to 5 mA 1, 2, 3 01 25 mV T
38、otal output variation VTV3/ 1, 2, 3 01 -150 +150 mV Long term stability LTS 1000 hours, TA= +125C 2 01 25 mV Output short circuit current IOS1, 2, 3 01 -10 -30 mA Oscillator section Initial accuracy IA1, 2, 3 01 41 57 kHz SYNC, low output voltage VOLIOUT= +1 mA 1, 2, 3 01 0.4 V SYNC, high output vol
39、tage VOHIOUT= -5 mA 1, 2, 3 01 2.4 V SYNC, low input voltage VILCT= 0 V, RT= VREF1, 2, 3 01 0.8 V SYNC, high input voltage VIHCT= 0 V, RT= VREF1, 2, 3 01 2.0 V SYNC, input current IINS1, 2, 3 01 -1 1 A SYNC delay to outputs tSDCT= 0 V, RT= VREF, VSYNC= 0.8 V to 2.0 V 9, 10, 11 01 100 ns Error amplif
40、ier section Input offset voltage VIN1, 2, 3 01 5 mV Input bias current IIB1, 2, 3 01 -1 A Input offset current IIN1, 2, 3 01 500 nA Common mode range VCM 1, 2, 3 01 0 VIN - 2 V Open loop gain AOLVOUT= 1.0 V to 4.0 V 1, 2, 3 01 80 dB Unity gain bandwidth UGBW 1, 2, 3 01 1 MHz Output sink current ISIV
41、ID -20 mA, COMP = 1.0 V 1, 2, 3 01 1 mA Output source current ISOVID 20 mA, COMP = 3.0 V 1, 2, 3 01 -80 A Output high level voltage VOHVID= 50 mV 1, 2, 3 01 4.5 V Output low level voltage VOLVID= -50 mV 1, 2, 3 01 0.5 V See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or n
42、etworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94575 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA +125C unless ot
43、herwise specified Group A subgroups Device type Limits 2/ Unit Min Max Current sense amplifier section. Amplifier gain VCLV-CS= 0 V, 3/ 4/ V+CS= 0 V 1, 2, 3 01 2.7 3.35 V/V Maximum differential input signal (+CS to -CS) VINDVCLApin = VREF, V+IN= VREF, V-IN= 0 V 1, 2, 3 01 1.1 V Input offset voltage
44、VOSVCLApin = 0.5 V, COMP = open 1, 2, 3 01 30 mV Common mode rejection ratio CMRR VCM= 0 V to VIN- 3.5 V 4, 5, 6 01 60 dB Power supply refection ratio PSRR 1, 2, 3 01 56 dB Input bias current +IIBVCLA= 0.5 V, 3/ 1, 2, 3 01 1 A -IIBCOMP = open -1 Input offset current IIOVCLA= 0.5 V, 3/ COMP = open 1,
45、 2, 3 01 1 A Delay to outputs 5/ tDOV+IN= VREF, V-IN= 0 V, +CS, -CS pins = 0 V to 1.5 V step 9, 10, 11 01 175 ns Current limit adjust section Current limit offset voltage VLO V-CS= 0 V, V+CS= 0 V, COMP pin = open 1, 2, 3 01 0.40 0.60 V Input bias current IIB 1, 2, 3 01 1 A Shutdown terminal section
46、Threshold voltage VTH1, 2, 3 01 0.94 1.06 V Input voltage range VINR1, 2, 3 01 0 VINV Minimum latching current IL1, 2, 3 01 300 A Maximum non-latching current INL 1, 2, 3 01 80 A Delay to outputs tDOVSD= 0 V to 1.3 V 9, 10, 11 01 120 ns See footnotes at end of table. Provided by IHSNot for ResaleNo
47、reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94575 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL F SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C T
48、A +125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min Max Output section Output supply voltage VOUT1, 2, 3 01 2.5 15 V Output low level voltage VOUTLISINK= 20 mA 1, 2, 3 01 200 mV ISINK= 100 mA 1.1 V Output high level voltage VOUTHISINK= -20 mA 1, 2, 3 01 11.8 V ISINK= -100 mA 11 Rise time tRCL= 1 nF, TA= 25C 9 01 65 ns Fall time tFCL= 1 nF, TA= 25C 9 01 65 ns Under-voltage lock-out section Start-up current ISUVCC start threshold 1, 2, 3 01 100 A Operation supply current ICC1, 2, 3 01 1.4 mA VCC shunt voltage VSHICC=10 mA 1, 2, 3 01 15 1
