1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with the notice of revision 5962-R043-95 - jak 95/06/16 Thomas M. Hess B Changes in accordance with the notice of revision 5962-R249-97 - jak 97-03-14 Monica L. Poelking C Update the boilerplate to the current requirements o
2、f MIL-PRF-38535. - jak 08-06-09 Thomas M. Hess D Correct the limits for output current test in table I. Editorial changes throughout.- jak 12-12-03 Thomas M. Hess REV SHEET REV D D D D D D SHEET 15 16 17 18 19 20 REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 1
3、3 14 PMIC N/A PREPARED BY Joseph A. Kerby DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING CHECKED BY Thanh V. Nguyen THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ADVANCED BIP
4、OLAR CMOS, OCTAL BUS TRANSCEIVER AND REGISTER WITH THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-04-15 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-94577 SHEET 1 OF 20 DSCC FORM 2233 APR 97 5962-E086-13 Prov
5、ided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94577 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assuranc
6、e class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is
7、 reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 94577 01 Q X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA desi
8、gnator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) i
9、ndicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ABT646 Octal bus transceiver and register with three-state outputs, TTL compatible inputs 02 54ABT646A Octal bus transceiver and register wit
10、h three-state outputs, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non
11、-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style K GDFP2-F24
12、 or CDFP3-F24 24 Flat pack L GDIP3-T24 or CDIP4-T24 24 Dual-in-line 3 CQCC1-N28 28 Leadless-chip-carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q, and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or ne
13、tworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94577 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc DC input voltage r
14、ange (VIN) (except I/O ports) -0.5 V dc to +7.0 V dc 4/ DC input voltage range (VIN) (I/O ports) . -0.5 V dc to +5.5 V dc 4/ DC output voltage range (VOUT) -0.5 V dc to +5.5 V dc 4/ DC input clamp current (IIK) (VIN= 0.0 V) . -18 mA DC output clamp current (IOK) (VOUT 0.0 V) . -50 mA DC output curre
15、nt (IOL) (per output) +96 mA Storage temperature range (TSTG) -65C to +150C Maximum power dissipation (PD) . 376 mW 5/ Lead temperature (soldering, 10 seconds) . +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recommended operating conditions. 2
16、/ 3/ Supply voltage range (VCC) . +4.5 V dc to +5.5 V dc Input voltage range (VIN) . +0.0 V dc to VCCOutput voltage range (VOUT) . +0.0 V dc to VCCMaximum low level input voltage (VIL ) 0.8 V Minimum high level input voltage (VIH ) . 2.0 V Case operating temperature range (TC) . -55C to +125C Maximu
17、m input rise or fall rate (t/V) (outputs enabled) 5 ns/V Maximum high level output current (IOH) -24 mA Maximum low level output current (IOL) . +48 mA 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade perform
18、ance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ The input negative voltage rating mat be exceeded provided that t
19、he input clamp current rating is observed 5/ Power dissipation values are derived using the formula PD= VCCICC+ nVOLIOL, where VCCand IOLare as specified in 1.4 above, ICCand VOLare as specified in table I herein, and n represents the total number of outputs. Provided by IHSNot for ResaleNo reproduc
20、tion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94577 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following speci
21、fication, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Sp
22、ecification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawing
23、s. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the refere
24、nces cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in ac
25、cordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance wit
26、h MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and he
27、rein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagr
28、am shall be as specified on figure 3. 3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and test circuit shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.3 Electrical
29、 performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requir
30、ements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94577 DLA
31、LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to sp
32、ace limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with
33、 MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For
34、device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an appr
35、oved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-3
36、8535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of
37、microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verificatio
38、n and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime s agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of
39、the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 126 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MI
40、CROCIRCUIT DRAWING SIZE A 5962-94577 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specifie
41、d Device type VCCGroup A subgroups Limits 3/ Unit Min Max High level output voltage 3006 VOHFor all inputs affecting output under test, VIN = VIH= 2.0 V or VIL= 0.8 V IOH= -3.0 mA All 4.5 V 1, 2, 3 2.5 V 5.0 V 1, 2, 3 3.0 IOH= -24 mA 4.5 V 1, 2, 3 2.0 Low level output voltage 3007 VOLFor all inputs
42、affecting output under test, VIN = VIH= 2.0 V or VIL= 0.8 V IOL= 48 mA All 4.5 V 1, 2, 3 0.55 V Three-state output leakage current, high 3021 IOZH4/ 5/ For control inputs affecting outputs under test, VIN= 2.0 V or 0.8 V VOUT= 2.7 V All 5.5 V 1, 2, 3 10.0 A Three-state output leakage current, low 30
43、20 IOZL4/ 5/ For control inputs affecting outputs under test, VIN= 2.0 V or 0.8 V VOUT= GND All 5.5 V 1, 2, 3 -10.0 A Negative input clamp voltage 3022 VIC- For input under test, IIN= -18 mA All 4.5 V 1, 2, 3 -1.2 V Off-state leakage current IOFFFor input or output under test, VINor VOUT= 4.5 V All
44、others pins at 0.0 V All 0.0 V 1 100 A High-state leakage current ICEXFor output under test, VOUT= 5.5 V Outputs at high logic state All 5.5 V 1, 2, 3 50 A Input current high 3010 IIH6/ Control pins For input under test, VIN= VCC01 5.5 V 1, 2, 3 +2.0 A 02 +1.0 A or B ports For input under test, VIN=
45、 VCCAll 5.5 V 1, 2, 3 +100 Input current low 3009 IIL6/ Control pins For input under test VIN= GND 01 5.5 V 1, 2, 3 -2.0 A 02 -1.0 A or B ports For input under test VIN= GND All 5.5 V 1, 2, 3 -100 Output current 3011 IO7/ VOUT= 2.5 V All 5.5 V 1 -50 -180 mA Quiescent supply current delta, TTL input
46、level 3005 ICC8/ For input under test, VIN= 3.4 V For all other inputs, VIN= VCCor GND 01 5.5 V 1, 2, 3 2.5 mA 02 1.5 See footnotes at end of table.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94577 DLA LA
47、ND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Device type VCCGroup A subgroups Limits 3
48、/ Unit Min Max Quiescent supply current, outputs high 3005 ICCHFor all inputs, VIN= VCCor GND IOUT= 0 A All 5.5 V 1, 2, 3 250 A Quiescent supply current, outputs low 3005 ICCLFor all inputs, VIN= VCCor GND IOUT= 0 A All 5.5 V 1, 2, 3 30 mA Quiescent supply current, outputs disabled 3005 ICCZFor all inputs, VIN= VCCor GND IOUT= 0 A All 5.5 V 1, 2, 3 250 A Input capacitance 3005 CINControl inputs TC= +25C See 4.4.1c All 5.0 V 4 14.5 pF Input/output capacitance 3005 CI/OA or B ports TC= +25C See 4.4.1b All 5.0 V 4 19.5 pF Low level ground
