1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with N.O.R. 5962-R071-96. 96-03-08 M. A. FRYE B Add thermal resistance, junction-to-case limits (JC) and terminal connections description. - ro 02-01-24 R. MONNIN REV SHET REV B B SHET 15 16 REV STATUS REV B B B B B B B B B
2、B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY SANDRA ROONEY DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY SANDRA ROONEY COLUMBUS, OHIO 43216 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL A.
3、FRYE MICROCIRCUIT, LINEAR, 8-BIT FLASH A/D CONVERTER, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 95-04-24 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-94771 SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E065-02 DISTRIBUTION STATEMENT A. Approved for public
4、 release; distribution is unlimited.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94771 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 S
5、cope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choic
6、e of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 94771 01 M X X Federal stock class designator RHA designator (see 1.2.1) Devicetype (see 1.2.2) Device class designator Caseoutline (see 1.2.4) Lead finish (see 1.2.
7、5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked w
8、ith the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 SPT7710A 8-Bit 150 MSPS flash A/D converter 02 SPT7710B 8-Bit 150 MSPS flash A/D converter 03 S
9、PT7725A 8-Bit 300 MSPS flash A/D converter 04 SPT7725B 8-Bit 300 MSPS flash A/D converter 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to th
10、e requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive d
11、esignator Terminals Package style X See figure 1 44 Ceramic gull wing lead chip carrier Y See figure 1 42 Dual-in-line 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo repro
12、duction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94771 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Negative supply voltage (VEEto GND) .-7.0 V dc to +0.5
13、 V dc Ground voltage differential .-0.5 V dc to +0.5 V dc Analog input voltage .VEEto +0.5 V dc Reference input voltage VEEto +0.5 V dc Digital input voltage VEEto +0.5 V dc Reference current (VRTFto VRBF) .25 mA Digital output current 0 mA to -30 mA Storage temperature .-65C to +150C Lead temperatu
14、re (soldering, 10 seconds) .+300C Junction temperature (TJ) .+150C Thermal resistance, junction-to-case (JC) : Case X 20C/W Case Y 10.1C/W 1.4 Recommended operating conditions. Case operating temperature range .-55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbo
15、oks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement th
16、ereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
17、 HANDBOOKS DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Bu
18、ilding 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific ex
19、emption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-
20、,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94771 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and
21、 as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for
22、 non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1
23、Case outlines. The case outlines shall be in accordance with 1.2.4 herein and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics and post irradiation parameter limits. Unless otherwise specified herein, the ele
24、ctrical performance characteristics and post irradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tes
25、ts for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the
26、 manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appe
27、ndix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and
28、 V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of suppl
29、y in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M
30、, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawi
31、ng. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A. 3.9 Verification and review for device class M. For devi
32、ce class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device
33、class M devices covered by this drawing shall be in microcircuit group number 57 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94771 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS,
34、 OHIO 43216-5000 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Integral linearity IL No missing codes, 1 01,03 -0.75 +0.75 LSB FCLK=
35、100 kHz 2,3 -0.95 +0.95 1 02,04 -0.95 +0.95 2,3 -1.25 +1.25 Differential linearity DNL No missing codes, 1 01,03 -0.75 +0.75 LSB FCLK= 100 kHz 2,3 -0.95 +0.95 1 02,04 -0.95 +0.95 2,3 -0.95 +1.25 Offset error VRGuaranteed but not tested 1,2,3 All -30 +30 mV Input voltage range VIN1,2,3 All -2.0 0 V I
36、nput current IIN1,2,3 All 500 A Ladder resistance RL1,2,3 All 100 300 Signal to noise ratio SNR FIN= 3.58 MHz 1 01 46 dB 02,03 45 04 44 2,3 01 45 02,03 44 04 43 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD M
37、ICROCIRCUIT DRAWING SIZE A 5962-94771 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Li
38、mits Unit Min Max Signal to noise ratio SNR FIN= 50 MHz 1 01 42 dB 02 40 2,3 01 40 02 38 FIN= 100 MHz 1 03 39 04 38 2,3 03 38 04 37 Total harmonic distortion THD FIN= 3.58 MHz 1 01,03 48 dB 02,04 46 2,3 01 45 02 43 03 44 04 42 FIN= 50 MHz 1 01 40 02 39 2,3 01 38 02 37 See footnotes at end of table.
39、Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94771 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Co
40、ntinued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Total harmonic distortion THD FIN= 100 MHz 1 03 40 dB 04 39 2,3 03 37 04 35 Signal-to-noise and distortion SND FIN= 3.58 MHz 1 01 45 dB 02 43 03 44 04 42 2,3 01 43 02 41 03 4
41、2 04 40 FIN= 50 MHz 1 01 39 02 37 2,3 01 37 02 35 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94771 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B
42、 SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Signal-to-noise and distortion SND FIN= 100 MHz 1 03 37 dB 04 35 2,3 03 34 04 32 Digital inpu
43、t high voltage VINH1,2,3 All -1.1 V Digital input low voltage VINL1,2,3 All -1.5 V Clock width tPWSee figure 3 9,10,11 01,03 4 ns 02,04 2 Digital output high voltage VOH1,2 All -1.1 V 3 -1.2 Digital output low voltage VOL1,2,3 All -1.5 V Supply current IDD1 All 550 mA 2,3 625 Power dissipation PD1 A
44、ll 2.9 W2,3 3.3 1/ Unless otherwise specified, VEE= 5.2 V, RSOURCE= 50 , VRBF= 2 V, VR2= 1 V, VRTF= 0 V, fCLK= 150 MHz, and duty cycle = 50 %. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94771 DEFENSE SUP
45、PLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 9 DSCC FORM 2234 APR 97 Case outline X Symbol Millimeter Min Nom Max A1 2.03 2.67 A2 0.20 b 0.40 C 0.15 D,E 17.60 18.01 D1,E1 14.00 e 1.00 BSC L1 0.70 1.30 FIGURE 1. Case outline. Provided by IHSNot for ResaleNo reproduction or net
46、working permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94771 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 10 DSCC FORM 2234 APR 97 Case outline Y Symbol Inches Millimeters Min Nom Max Min Nom Max A .081 .099 .099 2.06 2.51 2.51 b .
47、016 .020 .020 0.41 0.51 0.51 b2 .050 1.27 C .008 .016 0.20 0.38 D 2.080 1.120 52.83 63.85 E .585 .605 14.88 15.37 e .100 BSC 2.54 BSC eA .600 .620 15.24 15.75 L .275 6.99 Q .050 1.27 NOTE: The U.S. Government preferred system of measurement is the metric SI system. However, since This item was origi
48、nally designed using inch-pound units of measurement, in the event of conflict between the metric and inch-pound units shall take precedence. FIGURE 1. Case outline Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94771 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL B SHEET 11 DSCC FORM 2234 APR 97 Device types 01,02,03,04 Case outlines X Y Terminal number Term
