1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device types 03 and 04. Technical and editorial changes throughout. 96-02-06 M. A. FRYE B Drawing updated to reflect current requirements. ro 01-01-12 R. MONNIN C Make changes to IIOand IIBtests as specified in table I. -ro 01-01-31 R. MONNIN
2、 D Update drawing as part of 5 year review. -rrp 07-02-20 J. RODENBECK REV SHET REV SHET REV STATUS REV D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY RICK OFFICER DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY RAJESH PITHADIA COLUMBU
3、S, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MICHAEL FRYE MICROCIRCUIT, LINEAR, RAIL-TO-RAIL, DUAL/QUAD OPERATIONAL AMPLIFIER, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-10-20 AMSC N/A REVISION L
4、EVEL D SIZE A CAGE CODE 67268 5962-95504 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E256-06 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95504 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISIO
5、N LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Par
6、t or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 95504 01 Q C X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class de
7、signatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-3
8、8535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 TLV2262M Rail-to-rail, dual, operational
9、amplifier 02 TLV2264M Rail-to-rail, quad, operational amplifier 03 TLV2262AM Rail-to-rail, dual, operational amplifier with enhanced VIO04 TLV2264AM Rail-to-rail, quad, operational amplifier with enhanced VIO1.2.3 Device class designator. The device class designator is a single letter identifying th
10、e product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2
11、.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line D GDFP1-F14 or CDFP2-F14 14 Flat pack H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-i
12、n-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDAR
13、D MICROCIRCUIT DRAWING SIZE A 5962-95504 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VDD) . -0.5 V dc to +8.0 V dc 2/ Differential input voltage (VID) . VDD3/ Input voltage range (VIN)
14、. -VDD 0.3 V to +VDD2/ Input current, each input (IIN) +5.0 mA to 5.0 mA Output current (IOUT) . +50.0 mA to 50.0 mA Total current into +VDD+50.0 mA to 50.0 mA Total current out of VDD+50.0 mA to 50.0 mA Duration of short-circuit current at or below +25C Unlimited 4/ Maximum power dissipation (PD):
15、5/ Case C and 2 . 1375 mW Case D and H . 700 mW Case P . 1050 mW Storage temperature range (TSTG) . -65C to +150C Lead temperature (soldering 10 seconds) . +260C Maximum junction temperature (TJ) +150C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 1.4 Recommended operating conditions.
16、 Supply voltage (VDD) . 2.7 V dc to 8.0 V dc Input voltage range (VIN) . -VDDto +VDD 1.3 V Common-mode input voltage (VIC) -VDDto +VDD 1.3 V Ambient operating temperature (TA) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, s
17、tandards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification
18、 for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade p
19、erformance and affect reliability. 2/ All voltage values, except differential voltages, are with respect to the midpoint between +VDDand -VDD. 3/ Differential voltages are at the noninverting input with respect to the inverting input. Excessive current flows if the input is brought below -VDD- 0.3 V
20、. 4/ The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. 5/ Above TA= +25C, derate by the following factors; cases C and 2 at 11.0 mW/C, cases D and H at 5.5 mW/C, and case P at 8.4 mW/C. Provid
21、ed by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95504 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of S
22、tandard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 1911
23、1-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. RE
24、QUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or
25、function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shal
26、l be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1
27、. 3.2.3 Logic diagram. The logic diagram shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I
28、and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed
29、 in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator sha
30、ll still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as requir
31、ed in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of
32、 this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source
33、of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as requ
34、ired for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAW
35、ING SIZE A 5962-95504 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxInput off
36、set voltage VIOVDD= 1.5 V, VIC= 0 V, 1 01,02 2500 V RS= 50 , VOUT= 0 V 03,04 950 2,3 01,02 3000 03,04 1500 VDD= 2.5 V, VIC= 0 V, 1 01,02 2500 RS= 50 , VOUT= 0 V 03,04 950 2,3 01,02 3000 03,04 1500 Input offset current IIOVDD= 1.5 V, VIC= 0 V, RS= 50 , VOUT= 0 V, TA= +125C 2 All 800 pA VDD= 2.5 V, VI
37、C= 0 V, RS= 50 , VOUT= 0 V, TA= +125C 800 Input bias current IIBVDD= 1.5 V, VIC= 0 V, RS= 50 , VOUT= 0 V, TA= +125C 2 All 800 pA VDD= 2.5 V, VIC= 0 V, RS= 50 , VOUT= 0 V, TA= +125C 800 Common-mode input voltage range VICR VDD= 3 V, |VIO| 5 mV, 1 All 0 to 2 V RS= 50 2,3 0 to 1.7 VDD= 5 V, |VIO| 5 mV,
38、 1 0 to 4 RS= 50 2,3 0 to 3.5 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95504 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2
39、234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA +125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxHigh level output voltage VOHVDD= 3 V, VIC= 1.5 V, 1 All 2.85 V IOH= -100 A 2,3 2.82 VDD= 3 V, VIC= 1.5 V, 1 2.7 I
40、OH= -200 A 2,3 2.6 VDD= 5 V, VIC= 2.5 V, 1 4.85 IOH= -100 A 2,3 4.82 VDD= 5 V, VIC= 2.5 V, 1 4.7 IOH= -200 A 2,3 4.5 Low level output voltage VOLVDD= 3 V, VIC= 1.5 V, 1 01,03 0.15 V IOL= 500 A 2,3 0.165 1,2,3 02,04 0.15 VDD= 3 V, VIC= 1.5 V, IOL= 1 mA 1,2,3 All 0.3 VDD= 5 V, VIC= 2.5 V, IOL= 500 A 0
41、.15 VDD= 5 V, VIC= 2.5 V, IOL= 1 mA 0.3 Large-signal differential voltage amplification AVD VDD= 3 V, VIC= 1.5 V, 2/ 1 All 60 V/mV VOUT= 1 V to 2 V, RL= 50 k 2,3 25 VDD= 5 V, VIC= 2.5 V, 2/ 1 80 VOUT= 1 V to 4 V, RL= 50 k 2,3 50 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduc
42、tion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95504 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TA
43、+125C unless otherwise specified Group A subgroups Device type Limits 1/ Unit Min MaxCommon-mode rejection ratio CMRR VDD= 3 V, VOUT= 1.5 V, 1 All 65 dB VIC= 0 V to 1.7 V, RS= 50 2,3 60 VDD= 5 V, VOUT= 2.5 V, VIC= 0 V to 2.7 V, RS= 50 1,2,3 70 Supply voltage rejection ratio (VDD/ VIO) kSVRVDD= 2.7 V
44、 to 8 V, VIC= VDD/ 2, no load 1,2,3 All 80 dB VDD= 4.4 V to 8 V, VIC= VDD/ 2, no load 80 Supply current (both channels) IDDVDD= 3 V, VOUT= 1.5 V, 1,2,3 01,03 500 A no load 02,04 1000 VDD= 5 V, VOUT= 2.5 V, 01,03 500 no load 02,04 1000 Slew rate at unity gain SR VDD= 3 V, RL= 50 k, 2/ 4 All 0.35 V/s
45、VOUT= 0.5 V to 1.7 V, CL= 100 pF 5,6 0.25 VDD= 5 V, RL= 50 k, 2/ 4 0.35 VOUT= 0.5 V to 3.5 V, CL= 100 pF 5,6 0.25 1/ The algebraic convention, whereby the most negative value is a minimum and the most positive is a maximum, is used in this table. Negative current shall be defined as conventional cur
46、rent flow out of a device terminal. 2/ Referenced to 1.5 V for VDD= 3 V tests and 2.5 V for VDD= 5 V tests. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any
47、change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at
48、the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-95504 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REV
