1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R096-97. CFS 96-11-18 Monica L. Poelking B Add limit for linear energy threshold (LET) with no latch-up in section 1.5. Update the boilerplate to the requirements of MIL-PRF-38535. Editorial changes throughout.
2、 TVN 06-03-20 Thomas M. Hess C Update boilerplate paragraphs and radiation paragraphs 4.4.4.1 4.4.4.4 to the current MIL-PRF-38535 requirements. - LTG 12-03-22 Thomas M. Hess REV SHEET REV C SHEET 15 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A
3、 PREPARED BY Thanh V. Nguyen DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY Thanh V. Nguyen APPROVED BY Monica L. Poelki
4、ng MICROCIRCUIT, DIGITAL, RADIATION HARDENED, ADVANCED CMOS, 9-BIT ODD/EVEN PARITY GENERATOR/CHECKER, MONOLITHIC SILICON DRAWING APPROVAL DATE 96-05-20 REVISION LEVEL C SIZE A CAGE CODE 67268 5962-96582 SHEET 1 OF 15 DSCC FORM 2233 APR 97 5962-E255-12 Provided by IHSNot for ResaleNo reproduction or
5、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96582 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliabilit
6、y (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is a
7、s shown in the following example: 5962 H 96582 01 V X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked de
8、vices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type
9、(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ACS280 Radiation hardened, 9-bit odd/even parity generator/checker 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level
10、as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The ca
11、se outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line X CDFP3-F14 14 Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38
12、535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96582 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ra
13、tings. 1/ 2/ 3/ Supply voltage range (VDD) -0.3 V dc to +7.0 V dc DC input voltage range (VIN) -0.3 V dc to VDD + 0.3 V dc DC output voltage range (VOUT) . -0.3 V dc to VDD+ 0.3 V dc DC input current, any one input (IIN). 10 mA Latch-up immunity current (ILU) 150 mA Storage temperature range (TSTG)
14、. -65C to +150C Lead temperature (soldering, 5 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C Maximum power dissipation (PD) . 1.0 W 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VDD) +4.5 V dc to +5.5 V dc Input voltag
15、e range (VIN) 0.0 V dc to VDDOutput voltage range (VOUT). 0.0 V dc to VDDMaximum input rise or fall time at VDD= 4.5 V (tr, tf) 1 ns/V 4/ Case operating temperature range (TC) . -55C to +125C 1.5 Radiation features. 5/ Maximum total dose available (dose rate = 50 300 rads (Si)/s) 1 x 106Rads (Si) Si
16、ngle event phenomenon (SEP): Effective linear energy transfer (LET), no upsets (see 4.4.4.4) 80 MeV/(mg/cm2) 6/ Effective linear energy transfer (LET), no latch-up (see 4.4.4.4) 120 MeV/(mg/cm2) 6/ Dose rate upset (20 ns pulse) 1 x 109Rads (Si)/s Latch-up . None Dose rate survivability 1 x 1012Rads
17、(Si)/s 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise specified, all voltages are referenced to VSS. 3/ The limits for the parameters specified herein
18、 shall apply over the full specified VDDrange and case temperature range of -55C to +125C unless otherwise specified. 4/ Derate system propagation delays by difference in rise time to switch point for tror tf 1 ns/V. 5/ Radiation testing is performed on the standard evaluation circuit. 6/ Limits obt
19、ained during technology characterization/qualification, guaranteed by design or process, but not production tested unless specified by the customer through the purchase order or contract. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICRO
20、CIRCUIT DRAWING SIZE A 5962-96582 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the ex
21、tent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Meth
22、od Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps
23、.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothi
24、ng in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 as specified herein, or as modified in
25、the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as s
26、pecified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall
27、be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and te
28、st circuit. The switching waveforms and test circuit shall be as specified on figure 4. 3.2.6 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing and acquiring activity u
29、pon request. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table IA and shall apply over the full case operating temperature range
30、. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table IA. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT
31、DRAWING SIZE A 5962-96582 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN nu
32、mber is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class
33、 M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 C
34、ertificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in
35、 order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V,
36、 the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall
37、 be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects
38、 this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made availa
39、ble onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 39 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
40、nse from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96582 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE IA. Electrical performance characteristics. Test Symbol Test conditions 1/ -55C TC +125C unless otherwise specified Device type VDDGro
41、up A subgroups Limits 2/ Unit Min Max High level input voltage VIH All 4.5 V 1, 2, 3 3.15 V M, D, P, L, R, F, G, H 3/ All 1 3.15 All 5.5 V 1, 2, 3 3.85 M, D, P, L, R, F, G, H 3/ All 1 3.85 Low level input voltage VIL All 4.5 V 1, 2, 3 1.35 V M, D, P, L, R, F, G, H 3/ All 1 1.35 All 5.5 V 1, 2, 3 1.6
42、5 M, D, P, L, R, F, G, H 3/ All 1 1.65 High level output voltage VOH For all inputs affecting output under test, VIN= VDDor VSSIOH= -100 A All 4.5 V 1, 2, 3 4.25 V M, D, P, L, R, F, G, H 3/ All 1 4.25 Low level output voltage VOL For all inputs affecting output under test, VIN= VDDor VSSIOL= 100 A A
43、ll 4.5 V 1, 2, 3 0.25 V M, D, P, L, R, F, G, H 3/ All 1 0.25 Input current high IIH For input under test, VIN= VDDFor all other inputs, VIN= VDDor VSSAll 5.5 V 1, 2, 3 +1.0 A M, D, P, L, R, F, G, H 3/ All 1 +1.0 Input current low IIL For input under test, VIN= VSSFor all other inputs, VIN= VDDor VSS
44、All 5.5 V 1, 2, 3 -1.0 A M, D, P, L, R, F, G, H 3/ All 1 -1.0 Output current (source) IOH4/ For output under test, VOUT= VDD - 0.4 V VIN= VDDor VSSAll 4.5 V and 5.5 V 1, 2, 3 -8.0 mA M, D, P, L, R, F, G, H 3/ All 1 -8.0 Output current (sink) IOL4/ For output under test, VOUT= 0.4 V VIN= VDDor VSSAll
45、 4.5 V and 5.5 V 1, 2, 3 8.0 mA M, D, P, L, R, F, G, H 3/ All 1 8.0 Quiescent supply current IDDQVIN= VDDor VSSAll 5.5 V 1, 2, 3 10.0 A M, D, P, L, R, F, G, H 3/ All 1 10.0 Short circuit output current IOS5/ 6/ VOUT= VDDand VSSAll 5.5 V 1, 2, 3 200 mA See footnotes at end of table. Provided by IHSNo
46、t for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96582 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE IA. Electrical performance characteristics Continued. Test Symbol Test
47、 conditions 1/ -55C TC +125C unless otherwise specified Device type VDDGroup A subgroups Limits 2/ Unit Min Max Input capacitance CINf = 1 MHz See 4.4.1c All 0.0 V 4 15.0 pF Output capacitance COUTf = 1 MHz See 4.4.1c All 0.0 V 4 15.0 pF Switching power dissipation PSW7/ CL= 50 pF, per switching out
48、put All 4.5 V and 5.5 V 4, 5, 6 2.2 mW/ MHz M, D, P, L, R, F, G, H 3/ All 4 2.2 Functional test 8/ VIH= 0.7 VDD, VIL= 0.3 VDD See 4.4.1b All 4.5 V and 5.5 V 7, 8 L H M, D, P, L, R, F, G, H 3/ All 7 L H Propagation delay time, any input to EVEN tPLH19/ CL= 50 pF minimum See figure 4 All 4.5 V and 5.5 V 9, 10, 11 1.0 20.0 ns M, D, P, L, R, F, G, H 3/ All 9 1.0 20.0 tPHL19/ CL= 50 pF minimum See figure 4 All 4.5 V and 5.5 V 9, 10, 11 1.0 20.0 M, D, P, L, R, F, G, H 3/ All 9 1.0 20.0 Propagation delay time, any input to ODD tPLH29/ CL= 50 pF minimum See figure 4 All 4.5 V and 5
