1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R360-97. 97-06-27 Monica L. Poelking B Changes in accordance with NOR 5962-R446-97. 97-09-12 Monica L. Poelking C Redrawn with changes: Incorporate previous NORs. Update the boilerplate paragraphs to the curren
2、t MIL-PRF-38535 requirements. - LTG 09-02-19 Charles F. Saffle REV SHET REV C C SHET 15 16 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby CHECKED BY Thanh V. Nguyen DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3
3、990 http:/www.dscc.dla.mil APPROVED BY Monica L. Poelking STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 96-04-18 MICROCIRCUIT, DIGITAL, ADVANCED HIGH SPEED CMOS, OCTAL BUFFER/DRIVER WITH INVERTING TH
4、REE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-96806 SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E183-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SI
5、ZE A 5962-96806 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choi
6、ce of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 96806 01 Q R A Federal stock cla
7、ss designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the a
8、ppropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device ty
9、pe Generic number Circuit function 01 54AHCT240 Octal buffer/driver with inverting three-state outputs, TTL compatible inputs 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentati
10、on M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as f
11、ollows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-3
12、8535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96806 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute
13、maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc DC input voltage range (VIN) -0.5 V dc to +7.0 V dc 4/ DC output voltage range (VOUT) . -0.5 V dc to +7.0 V dc 4/ DC input clamp current (IIK) (VINVCC). -20 mA DC output clamp current (IOK) (VOUTVCC) -20 mA Continuous output
14、 current (IOL) (VO= 0 to VCC) 25 mA Continuous current through VCCor GND 75 mA Storage temperature range (TSTG) . -65C to +150C Lead temperature (soldering, 10 seconds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C Maximum power dissipation at TA
15、= +55C (in still air) (PD) . 500 mW 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) +4.5 V dc to +5.5 V dc Minimum high level input voltage (VIH). +2.0 V Maximum low level input voltage (VIL) +0.8 V Input voltage range (VIN) +0.0 V dc to VCCOutput voltage range (VOUT). +0.0 V
16、dc to VCCMaximum high level output current (IOH) -8 mA Maximum low level output current (IOL) +8 mA Maximum input rise or fall rate (t/V). +20 ns/V Case operating temperature range (TC). -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following speci
17、fication, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Sp
18、ecification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawing
19、s. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extende
20、d operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. Unused inputs m
21、ust be held high or low. 4/ The input and output voltage ratings may be exceeded provided that the input and output current ratings are observed. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96806 DEFENSE
22、SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersed
23、es applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Ma
24、nagement (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, constr
25、uction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
26、 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce load circuit and waveforms. The ground bounce l
27、oad circuit and waveforms shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. 3.2.7 Radiation exposure circuit. The radiation exposure circuit shall be as specified when available. 3.3 Electrical p
28、erformance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirem
29、ents. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marki
30、ng of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-3853
31、5. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-P
32、RF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be requ
33、ired from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classe
34、s Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, append
35、ix A shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96806 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C
36、 SHEET 5 DSCC FORM 2234 APR 97 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device clas
37、s M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device cla
38、ss M. Device class M devices covered by this drawing shall be in microcircuit group number 37 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96806 DEFENSE SUPPLY CENTER COLUMB
39、US COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified VCCGroup A subgroups Min Max Unit IOH= -50 A
40、 1, 2, 3 4.4 1 3.94 High level output voltage 3006 VOHFor all inputs affecting output under test VIN= 2.0 V or 0.8 V For all other inputs VIN= VCCor GND IOH= -8.0 mA 4.5 V2, 3 3.8 V IOL= 50 A 1, 2, 3 0.1 1 0.36 Low level output voltage 3007 VOLFor all inputs affecting output under test VIN= 2.0 V or
41、 0.8 V For all other inputs VIN= VCCor GND IOL= 8.0 mA 4.5 V2, 3 0.44 V 1 +0.25Three-state output leakage current high 3021 IOZHmOE= 2.0 V For all other inputs, VIN= VCCor GND VOUT= VCC5.5 V2, 3 +2.5 A 1 -0.25 Three-state output leakage current low 3020 IOZLmOE= 2.0 V For all other inputs, VIN= VCCo
42、r GND VOUT= GND 5.5 V2, 3 -2.5 A 1 +0.1 Input current high 3010 IIHFor input under test VIN= VCCFor all other inputs, VIN= VCCor GND 5.5 V2, 3 +1.0 A 1 -0.1 Input current low 3009 IILFor input under test VIN= GND For all other inputs, VIN= VCCor GND 5.5 V2, 3 -1.0 A 1 4.0 Quiescent supply current 30
43、05 ICCFor all inputs, VIN= VCCor GND IOUT= 0.0 A 5.5 V2, 3 40.0 A 1 1.35 Quiescent supply current delta, TTL input levels 3005 ICC4/ One input at 3.4 V Other inputs at VCCor GND 5.5 V2, 3 1.5 mA Input capacitance 3012 CINTC= +25C, VIN= VCCor GND See 4.4.1c 5.0 V4 8.5 pF Output capacitance COUTTC= +2
44、5C, VOUT= VCCor GND See 4.4.1c 5.0 V4 8.5 pF Power dissipation capacitance CPD5/ CL= 50 pF minimum f = 1 MHz See 4.4.1c 5.0 V4 11.0 pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A
45、 5962-96806 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Limits 3/ Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise spec
46、ified VCCGroup A subgroups Min Max Unit Low level ground bounce noise VOLP6/ 5.0 V 4 1900 Low level ground bounce noise VOLV6/ 5.0 V 4 -1750 High level VCCbounce noise VOHP6/ 5.0 V 4 750 High level VCCbounce noise VOHV6/ CL= 50 pF minimum TA= +25C See 4.4.1d See figure 4 5.0 V 4 -1100 mV 4.5 V Funct
47、ional test 3014 7/ VIH= 2.0 V, VIL= 0.8 V Verify output VOSee 4.4.1b 5.5 V 7, 8 L H 9 1 7.4 CL= 15 pF minimum RL= open See figure 5 9/ 4.5 V and 5.5 V 10, 11 1 8.5 ns 9 1 8.4 tPLH8/ CL= 50 pF minimum RL= open See figure 5 4.5 V and 5.5 V 10, 11 1 9.5 ns 9 1 7.4 CL= 15 pF minimum RL= open See figure
48、5 9/ 4.5 V and 5.5 V 10, 11 1 8.5 ns 9 1 8.4 Propagation delay time, mAn to mYn 3003 tPHL8/ CL= 50 pF minimum RL= open See figure 5 4.5 V and 5.5 V 10, 11 1 9.5 ns 9 1 10 CL= 15 pF minimum RL= 1 k See figure 5 9/ 4.5 V and 5.5 V 10, 11 1 12 ns 9 1 11 tPZH8/ CL= 50 pF minimum RL= 1 k See figure 5 4.5 V and 5.5 V 10, 11 1 13 ns 9 1 10 CL= 15 pF minimum RL= 1 k See figure 5 9/ 4.5 V and 5.5 V 10, 11 1 12 ns 9 1 11.4 Propagation delay time, output enable, mOE to mYn 3003 tPZL8/ CL= 50 pF minimum RL= 1 k See figure 5 4.5 V and 5.5 V 10,
