1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - ro 02-04-18 R. MONNIN B Make a change to footnote 1/ under Table I. Make changes to +VOUTtest under Table I. Add new footnote 2/ to the VOUTtest under Table I. - ro 06-12-08 R. MONNIN C Add devic
2、e type 02 and RHA designator “R” requirements. Add case outline H. Add paragraphs 1.4.1, 1.5, 3.2.3, 4.4.4.1, and Table IIB. Make changes to 1.2, 1.2.2, 1.3, Table I, and figure 1. Add a footnote 4/ to the IStest as specified under Table I. Make changes to CMRR, PSRR tests, footnote 1/ for device ty
3、pe 01 as specified under Table I. - ro 09-12-09 C. SAFFLE D In Table I, add the word “mode” after Disabled in the conditions column for IStest. In Table I, add “” to VOS, IIB, and IOSmax limits column. In Table I, under footnote 4/, add the words “Disabled mode” at beginning of note. Delete the burn
4、 in and group c end point limits from Table IIB. - ro 10-02-22 C. SAFFLE E Add device type 03 tested at low dose rate. Make changes to paragraphs 1.2.2, 1.5, 4.4.4.1 and Table I. - ro 11-09-08 C. SAFFLE REV SHET REV SHET REV STATUS REV E E E E E E E E E E E E OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11
5、12 PMIC N/A PREPARED BY RICK OFFICER DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY MICHAEL FRYE MICR
6、OCIRCUIT, LINEAR, 160 MHz, RAIL-TO-RAIL AMPLIFIER WITH DISABLE, MONOLITHIC SILICON DRAWING APPROVAL DATE 96-03-29 AMSC N/A REVISION LEVEL E SIZE A CAGE CODE 67268 5962-96839 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E415-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without
7、license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96839 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) an
8、d space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following exam
9、ple: 5962 R 96839 02 V H A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 spe
10、cified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify
11、 the circuit function as follows: Device type Generic number Circuit function 01 AD8041 160 MHz rail-to-rail amplifier with disable 02 AD8041 Radiation hardened, 160 MHz rail-to-rail amplifier with disable 03 AD8041 Radiation hardened, 160 MHz rail-to-rail amplifier with disable 1.2.3 Device class d
12、esignator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535
13、, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T8 8 Dual-in-line H GDFP1-F10 or CDFP2-F10 10 Flat pack
14、1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96839 DLA LAND A
15、ND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage ( +VSto VS) +12.6 V Input common mode range (VIN) . VSInternal power dissipation (PD) 1.3 W 2/ Junction temperature (TJ) +175C Storage temperature range . -65C to +125
16、C Lead temperature range (soldering, 60 seconds) +300C Thermal resistance, junction-to-case (JC) : Case H . 45C/W Case P 37C/W Thermal resistance, junction-to-ambient (JA) : Case H . 190C/W Case P 88C/W 3/ 1.4 Recommended operating conditions. Supply voltage (VS) 2.5 V (+5 V / 0 V) to 5 V Operating
17、ambient temperature range (TA) . -55C to +125C 1.4.1 Operating performance characteristics. Input / output characteristics : (TA= +25C, VS= 2.5 V, RL= 2 k to 0 V) Output current (VO= -2 V to +2 V) . 50 mA Input common mode voltage range -2.5 V to +1.5 V Dynamic performance: (TA= +25C, VS= 2.5 V, RL=
18、 2 k to 0 V) -3 db small signal bandwidth (VO 0.5 VPP, G = 1) . 160 MHz Bandwidth for 0.1 dB flatness (G = +2, RL= 150 ) . 30 MHz Slew rate (G = -1, VO= 2 V step) . 160 V/s Full power response (VO= 2 VPP) . 24 MHz Noise /distortion performance: (TA= +25C, VS= 2.5 V, RL= 2 k to 0 V) Total harmonic di
19、stortion (fC= 5 MHz, VO= 2 VPP, G = +2, RL= 1 k) -72 dB Input voltage noise (f = 10 kHz) 16 nV/ Hz Disable characteristics: (TA= +25C, VS= 2.5 V, RL= 2 k to 0 V, VO= 2 VPPat 10 MHz, G = +2) Turn off time (RF= RL= 2 k) . 120 ns Turn on time (RF= RL= 2 k) . 230 ns Off isolation ( DISABLE pin tied to V
20、S, RL= 100 , f = 5 MHz, G = +2, RF= 1 k) 70 dB Off voltage (device disabled) +VS 2.5 V On voltage (device enabled) . Open or +VS_ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliab
21、ility. 2/ Maximum internal power dissipation is specified so that the junction temperature does not exceed +175C. In product application, additional power dissipation created by output load current must not allow internal power dissipation absolute maximum limit to be exceeded. 3/ Derate at 9 mW/C f
22、or TA 32C. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96839 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 4 DSCC FORM 2234 APR 97 1.5 Radiation features. Device type 02: Maximum
23、total dose available (dose rate = 50 300 rads(Si)/s) 100 krads(Si) 4/ Device type 03: Maximum total dose available (dose rate 10 mrads(Si)/s) . 50 krads(Si) 5/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
24、 part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE ST
25、ANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are availab
26、le online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this
27、drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as s
28、pecified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-
29、JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case
30、outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections and block diagram. The terminal connections and block diagram shall be as specified on figure 1. 3.2.3 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer u
31、nder document revision level control and shall be made available to the preparing and acquiring activity upon request. _ 4/ For device type 02, this part may be dose rate sensitive in a space environment and may demonstrate enhanced low dose rate effects. Radiation end point limits for the noted par
32、ameters are guaranteed only for the conditions specified in MIL-STD-883, method 1019, condition A. 5/ For device type 03, radiation endpoint limits for the noted parameters are guaranteed for the condition specified in MIL-STD-883, method 1019, condition D. Provided by IHSNot for ResaleNo reproducti
33、on or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96839 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise spe
34、cified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table I
35、IA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN is not feasible due to space limitations, the manufactur
36、er has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5
37、.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certi
38、ficate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HD
39、BK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device c
40、lass M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this
41、 drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime -VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M
42、. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit
43、group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96
44、839 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ 2/ 3/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Quiescent supply current IS1,2
45、,3 All 6.1 mA M,D,P,L,R 1 02 6.1M,D,P,L 1 03 6.1 Disabled mode 4/ 1,2,3 All 1.7 M,D,P,L,R 1 02 1.7M,D,P,L 1 03 1.7 Input offset voltage VOS1,2,3 All 9.5 mV M,D,P,L,R 1 02 9.5 M,D,P,L 1 03 9.5 Common mode rejection ratio CMRR VCM= -1 V to 2.5 V 1,2,3 All 70 dB M,D,P,L,R 1 02 70M,D,P,L 1 03 70 Power s
46、upply rejection ratio PSRR VS= 2.5 V to 5.0 V 1,2,3 All 68 dB M,D,P,L,R 1 02 68M,D,P,L 1 03 68 Input bias current IIB1,2,3 All 3.4 A M,D,P,L,R 1 02 3.4 M,D,P,L 1 03 3.4 Input offset current IOS1,2,3 All 0.7 A M,D,P,L,R 1 02 0.7 M,D,P,L 1 03 0.7 See footnotes at end of table. Provided by IHSNot for R
47、esaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96839 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL E SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics continued. Test Symbol Conditions 1
48、/ 2/ 3/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Open loop gain AOLRL= 1 k 1,2,3 All 15 kV/V M,D,P,L,R 1 02 15M,D,P,L 03 15Positive output swing voltage +VOUTRL= 1 k 1,2,3 All 1.75 V M,D,P,L,R 1 02 1.75M,D,P,L 03 1.75RL= 50 1,2,3 All 1.45 M,D,P,L,R 1 02 1.45M,D,P,L 03 1.45Negative output swing voltage -VOUTRL= 1 k 1,2,3 All -2.15 V M,D,P,L,R 1 02 -2.15M,D,P,L 03 -2.15RL= 50 1,2,3 All -1.5 M,D,P,L,R 1 02 -1.5 M,D,P,L 03 -1.5 1/ Unless otherwise specified, VS= 2.5
