1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes are in accordance with the notice of revision (NOR) 5962-R261-97 - jak 97-04-01 Monica L. Poelking B Update the boilerplate to current requirements as specified in MIL-PRF-38535. - jak 08-06-25 Thomas M. Hess REV SHET REV B B B SHEET 15 1
2、6 17 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby STANDARD MICROCIRCUIT DRAWING CHECKED BY Monica L. Poelking DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE
3、FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 96-09-09 MICROCIRCUIT, DIGITAL, ADVANCED HIGH-SPEED CMOS, OCTAL BUFFER/DRIVER WITH THREE-STATE OUTPUTS, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 67268 5962-9
4、6850 SHEET 1 OF 17 DSCC FORM 2233 APR 97 5962-E410-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96850 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR
5、 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When
6、available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 96850 01 Q R A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead
7、 finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels
8、 and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54AHC540 Octal buffer/line driver three-state outputs 1.2.3 Device class desig
9、nator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, ap
10、pendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pack 2
11、 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROC
12、IRCUIT DRAWING SIZE A 5962-96850 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc DC input voltage range (VIN) . -0.5 V dc to +7.0 V dc 4/ DC output volta
13、ge range (VOUT) -0.5 V dc to VCC+ 0.5 V dc 4/ DC input clamp current (IIK) (VINVCC) . 20 mA Continuous output current (IO) (VOUT= 0 V to VCC) . 25 mA Continuous current through VCCor GND 75 mA Maximum power dissipation (PD) 500 mW Storage temperature range (TSTG) -65C to +150C Lead temperature (sold
14、ering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) . +175C 1.4 Recommended operating conditions. 2/ 3/ 5/ Supply voltage range (VCC) . +2.0 V dc to +5.5 V dc Input voltage range (VIN) . +0.0 V dc to +5.5 V dc Output voltage range (VOUT) +0
15、.0 V to VCCMinimum high level input voltage (VIH): VCC= 2.0 V . 1.5 V VCC= 3.0 V . 2.1 V VCC= 5.0 V 0.5 V . 3.85 V Maximum low level input voltage (VIL): VCC= 2.0 V . 0.5 V VCC= 3.0 V . 0.9 V VCC= 5.0 V 0.5 V . 1.65 V Maximum high level output current (IOH): VCC= 2.0 V . -50 A VCC= 3.3 V 0.3 V . -4
16、mA VCC= 5.0 V 0.5 V . -8 mA Maximum low level output current (IOL): VCC= 2.0 V . +50 A VCC= 3.3 V 0.3 V . +4 mA VCC= 5.0 V 0.5 V . +8 mA Minimum input rise or fall rate (t/V): VCC= 3.3 V V 0.3 V . 100ns/V VCC= 5.0 V V 0.5 V . 20ns/V Case operating temperature range (TC) -55C to +125C 1/ Stresses abo
17、ve the absolute maximum rating may cause permanent damage to the device, Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full
18、 specified VCCrange and case temperature range of -55C to +125C. 4/ The input and output voltage ratings may be exceeded providing that the input and output current ratings are observed. 5/ Unused inputs must be held high or low to prevent them from floating. Provided by IHSNot for ResaleNo reproduc
19、tion or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96850 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The follow
20、ing specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, G
21、eneral Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircui
22、t Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing a
23、nd the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V s
24、hall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in a
25、ccordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appe
26、ndix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. Th
27、e logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and test circuit shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. P
28、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96850 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.3 Electrical performance characteristics and post
29、irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requireme
30、nts shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is
31、not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall
32、 be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certifica
33、te of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order t
34、o be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-
35、PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lo
36、t of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review
37、for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment
38、 for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 37 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96850 DEFENSE SUPP
39、LY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +2.0 VCC +5.5 V unless otherwise specified VCCGroup A subgroups Limits 3/ Unit Min
40、Max2.0 V 1.9 3.0 V 2.9 IOH= -50 A 4.5 V 1, 2, 3 4.4 1 2.58 IOH= -4 mA 3.0 V 2, 3 2.48 1 3.94 High level output voltage 3006 VOHFor all inputs affecting outputs under test, VIN= VIHor VILFor all other inputs, VIN= VCCor GND IOH= -8 mA 4.5 V 2, 3 3.8 V 2.0 V 0.10 3.0 V 0.10 IOH= 50 A 4.5 V 1, 2, 3 0.1
41、0 1 0.36 IOH= 4 mA 3.0 V 2, 3 0.50 1 0.36 Low level output voltage 3007 VOLFor all inputs affecting outputs under test, VIN= VIHor VILFor all other inputs, VIN= VCCor GND IOH= 8 mA 4.5 V 2, 3 0.50 V 1 +0.1 Input current high 3010 IIHFor input under test, VIN= VCCFor all other inputs, VIN= VCCor GND
42、5.5 V 2, 3 +1.0 A 1 -0.1 Input current low 3009 IILFor input under test, VIN= GND For all other inputs, VIN= VCCor GND 5.5 V 2, 3 -1.0 A 1 +0.25 Three-state output leakage current, high 3021 IOZHOEn = VIHFor all other inputs, VIN= VCCor GND VOUT= VCC5.5 V 2, 3 +2.5 A 1 -0.25 Three-state output leaka
43、ge current, low 3020 IOZLOEn = VIHFor all other inputs, VIN= VCCor GND VOUT= GND 5.5 V 2, 3 -2.5 A 1 4.0 Quiescent supply current, 3005 ICCFor all inputs, VIN= VCCor GND IOUT= 0 A 5.5 V 2, 3 40 A Input capacitance 3012 CIN5.0 V 4 10 pF Output capacitance 3012 COUTTC= +25C VIN= VCCor GND See 4.4.1c 5
44、.0 V 4 10 pF Power dissipation capacitance CPD4/ CL= 50 pF minimum f = 1 MHz see figure 4 5.0 V 4 14 pF See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96850 DEFENSE SUPPLY CENT
45、ER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +2.0 VCC +5.5 V unless otherwise specified VCCGroup A subgroups Limits 3/ Unit M
46、in MaxVOLP5/ 5.0 V 4 1400 Low level ground bounce noise VOLV5/ 5.0 V 4 -1400 mV VOHP5/ 5.0 V 4 800 High level VCCbounce noise VOHV5/ VIH= VCCVIL= 0.0 V TA= +25C See 4.4.1d See figure 4 5.0 V 4 -1400 mV 2.0 V 3.0 V Functional tests 3014 8/ For all inputs, VIN= VIHor VILVerify output VOSee 4.4.1b 5.5
47、V 7, 8 L H 9 7.0 3.0 V and 3.6 V 10, 11 1.0 8.5 9 5.0 CL= 15 pF minimum See figure 5 8/ 4.5 V and 5.5 V 10, 11 1.0 6.0 ns 9 10.5 3.0 V and 3.6 V 10, 11 1.0 12.0 9 7.0 tPLH, 7/ CL= 50 pF minimum See figure 5 4.5 V and 5.5 V 10, 11 1.0 8.0 ns 9 7.0 3.0 V and 3.6 V 10, 11 1.0 8.5 9 5.0 CL= 15 pF minimu
48、m See figure 5 8/ 4.5 V and 5.5 V 10, 11 1.0 6.0 ns 9 10.5 3.0 V and 3.6 V 10, 11 1.0 12.0 9 7.0 Propagation delay time, An to Yn 3003 tPHL7/ CL= 50 pF minimum See figure 5 4.5 V and 5.5 V 10, 11 1.0 8.0 ns See footnotes on next sheet. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96850 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrica
