1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R150-97. 96-12-10 Raymond L. Monnin B Changes in accordance with NOR 5962-R194-97. 97-01-24 Raymond L. Monnin C Update drawing to current requirements. Editorial changes throughout. - gap 09-05-14 Joseph D. Rod
2、enbeck REV SHET REV SHET REV STATUS REV C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY Larry E. Shaw DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTM
3、ENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Tuan D Nguyen APPROVED BY Raymond Monnin MICROCIRCUIT, DIGITAL, BIPOLAR, SCHOTTKY TTL, HEX BUFFERS/LINE DRIVERS WITH 3-STATE OUTPUTS WITH 2 INDEPENDENT OR 2 DEPENDENT INPUTS, MONOLITHIC SILICON DRAWING APPROVAL DATE 96-09-04 AMSC N/A REVISION
4、 LEVEL C SIZE A CAGE CODE 67268 5962-96878 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E060-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96878 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVIS
5、ION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the P
6、art or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 96878 01 Q E X Federal stock class designator RHA designator (see 1.2.1) Devicetype (see 1.2.2)Deviceclass des
7、ignatorCaseoutline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-3853
8、5, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54365A Hex bus driver, non-inverted, 3-state
9、 outputs 02 54366A Hex bus driver, inverted, 3-state outputs 03 54367A Hex bus driver, non-inverted, 3-state outputs, w/2 independent enable inputs 04 54368A Hex bus driver, inverted, 3-state outputs, w/2 independent enable inputs 1.2.3 Device class designator. The device class designator is a singl
10、e letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualificati
11、on to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style E GDIP1-T16 or CDIP2-T16 16 Dual-in-line F GDFP2-F16 or CDFP3-F16 16 Flat package 1.2.5 Lead finish. The lead finish is as sp
12、ecified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96878 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3
13、990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) -0.5 V dc to +7.0 V dc Input voltage range (VIN) -0.5 V dc to +7.0 V dc Input current range (IIN) -30 mA to 5.0 mA Standard output . -0.5 V to VCCThree-state output . -0.5 V to 5.5 V Storag
14、e temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) . +300C Junction temperature (TJ) +175C Maximum power dissipation (PD) 2/ 500 mW 2/ Thermal resistance, junction-to-case (JC) See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage range (VCC) 4.5 V dc to 5.5
15、 V dc High level input voltage (VIH) 2.0 V Low level input voltage (VIL) . -0.8 V Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to t
16、he extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test
17、 Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.
18、daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. N
19、othing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliabilit
20、y. 2/ Maximum power dissipation is defined as VCCx ICCand must withstand the added PDdue to the short circuit output test (e.g., IOS). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96878 DEFENSE SUPPLY CENT
21、ER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality
22、 Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, con
23、struction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 here
24、in. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth tables. The truth tables shall be as specified on figure 2. 3.2.4 Logic diagrams. The logic diagrams shall be as specified on figure 3. 3.2.5 Test circuit and switching waveforms. The test circuit
25、 and switching waveforms shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply
26、over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In
27、addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked.
28、 Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535
29、. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see
30、6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
31、drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device cla
32、sses Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devi
33、ces acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore
34、documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 002 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction o
35、r networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96878 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC+125C unless othe
36、rwise specified Group A subgroupsDevice type Limits Unit Min Max High level output voltage VOHVCC= 4.5 V, VIL= 0.8 V, IOH= -2 mA, VIH= 2.0 V 1, 2, 3 All 2.4 V Low level output voltage VOLVCC= 4.5 V, VIH= 2.0 V, IOL=32 mA, VIL= 0.8 V 1, 2, 3 All 0.4 V Input clamp voltage VIKVCC= 4.5 V, II= -12 mA 1,
37、2, 3 All -1.5 V High level input current IIHVCC= 5.5 V, VIN= 2.4 V 1, 2, 3 All 40 A Low level input current A inputs IILVCC= 5.5 V, VIN= 0.5 V, Either G input at 2.0 V 1, 2, 3 All -40 A VCC= 5.5 V, VIN= 0.4 V, Both G inputs at 0.4 V All -1.6 mA G inputs VCC= 5.5 V, VIN= 0.4 V 1, 2, 3 All -1.6 mA Sho
38、rt circuit output current IOSVCC= 5.5 V 1/ 1, 2, 3 All -40 -130 mA Supply current ICCVCC= 5.5 V, Data inputs = 0 V, Output Controls = 4.5 V 1, 2, 3 01, 03 85 mA 02, 04 77 Output leakage current IOZH VCC= 5.5 V, VIH= 2 V, VIL= 0.8 V VOUT= 2.4 V 1, 2, 3 All 40 A IOZL VOUT= 0.4 V All -40 Functional tes
39、t See 4.4.1b 7, 8 All Propagation delay time, Into 0ntPLHRL= 400 , CL= 50 pF 9 01, 03 16 ns 02, 04 17 tPHL01, 03 22 ns 02, 04 16 Output enable time tPZH9 All 35 ns tPZL37 ns Output disable time tPHZRL= 400 CL= 5 pF 9 All 11 ns tPLZ27 ns 1/ Not more than one output should be shorted at a time. For te
40、sting IOS, the use of high speed test apparatus and/or sample and hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise prolonged shorting of a high output may raise the chip temperature well above normal and cause invalid read
41、ings in other parameter tests. In any sequence of parameter tests, IOStests should be performed last. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96878 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-
42、3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 Device type 01 02 03 and 04 Case outline E E and F E and F Terminal number Terminal symbol Terminal symbol Terminal symbol 1 G1 G1 1G 2 A1 A1 1A1 3 Y1 Y1 1Y14 A2 A2 1A2 5 Y2 Y2 1Y26 A3 A3 1A3 7 Y3 Y3 1Y38 GND GND GND 9 Y4 Y4 1Y4 10 A4 A4 1A4 11 Y5
43、Y5 2Y1 12 A5 A5 2A1 13 Y6 Y6 2Y2 14 A6 A6 2A2 15 G2 G2 2G 16 VCCVCCVCCFIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96878 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-
44、3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Device type 02 G1 G2 An Yn G1 G2 An Yn L L H H L L H L L L L L L L L H L H X Z L H X Z H L X Z H L X Z H H X Z H H X ZDevice type 03 1 G 1An 1Yn 2 G 2An 2Yn L L L L L L L H H L H H H X Z H X Z Device type 04 1 G 1An 1Yn 2 G 2An 2Yn L
45、 L H L L H L H L L H L H X Z H X Z FIGURE 2. Truth tables. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96878 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 223
46、4 APR 97 FIGURE 3. Logic diagrams. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96878 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 1/ CLincludes p
47、robe and jig capacitance. 2/ All diodes are 1N3064 or equivalent. 3/ When measuring propagation delay times of 3-state outputs, switches S1 and S2 are closed. 4/ Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is
48、 for an output with internal conditions such that the output is high except when disabled by the output control. FIGURE 4. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-96878 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device c
