1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Make changes to 3.2.4, figure 1, figure 4, table II, and add case outline H, 10-lead flat pack. - ro 99-04-12 R. MONNIN B Drawing updated to reflect current requirements. gt 02-12-30 R. MONNIN C Add Group A subgroups 5 and 6 to delay time test as
2、 specified in table I. - ro 03-02-12 R. MONNIN D Replace subgroups 4, 5, 6 with subgroups 9, 10, 11 for tdtest as specified under Table I. Replace subgroup 4 with subgroup 9 for tPLH1, tPHL1, tPLH2, tPHL2, tPLH3, tPHL3, tPLH4, tPHL4, tPLH5, tPHL5and both tWtests as specified under Table I. Under Tab
3、le II, delete subgroups 5, 6, and replace with subgroups 9, 10, 11. Update boilerplate paragraphs to current MIL-PRF-38535 requirements. - ro 11-07-27 C. SAFFLE REV SHET REV SHET REV STATUS REV D D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RAJESH P
4、ITHADIA DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY RAJESH PITHADIA APPROVED BY RAYMOND MONNIN MICROCIRCUIT, LINEAR, MICROPOWE
5、R SUPPLY VOLTAGE SUPERVISOR, MONOLITHIC SILICON DRAWING APPROVAL DATE 97-03-17 AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-97513 SHEET 1 OF 14 DSCC FORM 2233 APR 97 5962-E423-11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICRO
6、CIRCUIT DRAWING SIZE A 5962-97513 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V
7、). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 - 97513 01 Q H A Federal
8、stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked wi
9、th the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: D
10、evice type Generic number Circuit function 01 TLC7705 Micropower supply voltage supervisor 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to t
11、he requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive
12、designator Terminals Package style H GDFP1-F10 or CDFP2-F10 10 Flat pack P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. P
13、rovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97513 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage (VDD)
14、. +7.0 V dc 4/ Input voltage range, CONTROL, RESIN, SENSE . -0.3 V dc to +7.0 V dc 4/ Maximum low output current, (IOL) +10 mA Maximum high output current, (IOH) -10 mA Input clamp current (IIK) (VIN 0.0 or VIN VDD) . 10 mA Output clamp current (IOK) (VOUT 0.0 or VOUT VDD) 10 mA Continuous total pow
15、er dissipation (TA 25 C) 1 W Junction temperature (TJ) 150C Operating free-air temperature range, (TA) -55C to +125C Storage temperature range, (TSTG) . -65C to +150C Thermal resistance, junction to ambient (JA): Cases H and P . 180C/W Case 2 65C/W Thermal resistance, junction to case (JC) See MIL-S
16、TD-1835 1.4 Recommended operating conditions. Supply voltage range (VDD) +2.0 V dc to +6.0 V dc Input voltage range (VI) (0 to VDD) V High level input voltage at RESIN and CONTROL, (VIH) . (0.7 x VDD) V min 5/ Low level input voltage at RESIN and CONTROL, (VIL) (0.2 x VDD) V max 5/ High level output
17、 current (IOH) (VDD 2.7 V) -2 mA max Low level output current (IOL) (VDD 2.7 V) . 2 mA max Input transition rise and fall rate at RESIN and CONTROL, (t/V) 100 ns / V max Operating free-air temperature range (TA) -55C to +125C _ 1/ Stresses above the absolute maximum rating may cause permanent damage
18、 to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VDDrange and ambient temperature range of -55C
19、 to +125C. 4/ All voltage values are with respect to GND. 5/ To ensure a low supply current, VILshould be kept less than 0.3 V and VIHVDD-0.3 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97513 DLA LAND
20、AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise spe
21、cified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - I
22、nterface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardi
23、zation Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes ap
24、plicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Managem
25、ent (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, constructio
26、n, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.
27、2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Block diagram. The block diagram shall be as specified on figure 3. 3.3 Electrical performance characteristics and postirradiation parameter
28、 limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the s
29、ubgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN is not feasible due to space
30、 limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MI
31、L-PRF-38535, appendix A. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97513 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance ch
32、aracteristics. Test Symbol Conditions 1/ -55C TA +125C +2.0 V VDD +6.0 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max High level output voltage VOHIOH= -20 A, VDD= 2.0 V 1, 2, 3 01 1.7 V IOH= -20 A,VDD= 2.7 V 2.3 IOH= -20 A, VDD= 4.5 V 4.2 IOH= -2 mA, VDD= 4.5 V 3.6 L
33、ow level output voltage VOLIOL= 20 A, VDD= 2.0 V 1, 2, 3 01 0.2 V IOL= 20 A, VDD= 2.7 V 0.2 IOL= 20 A, VDD= 4.5 V 0.2 IOL= 2 mA, VDD= 4.5 V 0.5 Negative-going input threshold voltage, SENSE VITVDD= 2 V to 6 V 2/ 1, 2, 3 01 4.3 4.8 V Power-up reset voltage VRESIOL= 20 A 3/ 1, 2, 3 01 1.0 V Input curr
34、ent RESIN IIVI= 0 V to VDD1, 2, 3 01 2.0 A CONTROL VI= VDD15.0 SENSE VI= 5 V 10.0 Supply current IDDRESIN = VDD, SENSE = VDD VIT max + 0.2 V, CONTROL = 0 V, outputs open 1, 2, 3 01 16 A Supply current during tdIDD(d)VDD= 5 V, VCT= 0 V, RESIN = VDD, outputs open, SENSE = VDD,CONTROL = 0 V 1, 2, 3 01
35、150 A Input capacitance, SENSE CINVI= 0 V to VDD, see 4.4.1d 4 01 50 pF Functional test See 4.4.1c 7, 8 01 L H See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97513 DLA LAND AND
36、 MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics - Continued. Test Symbol Conditions 1/ -55C TA +125C +2.0 V VDD +6.0 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Delay time, VI(SENSE)
37、 VIT+ toRESET andRESETtdRL= 2 k, CL= 50 pF, RESIN = 2.7 V, VDD= 5.0 V, CONTROL = 0.4 V, CT= 100 nF, see figure 4 9,10,11 01 1.1 4.2 ms Propagation delay time, SENSE to RESET tPLH1RL= 2 k, CL= 50 pF, VIH= VIT+max + 0.2 V, VIL= VIT-min - 0.2 V, 9 01 24 s tPHL1RESIN = 2.7 V, VDD= 5.0 V, CONTROL = 0.4 V
38、, CT= NC, see figure 4 4/ 7 Propagation delay time, SENSE to RESET tPLH2RL= 2 k, CL= 50 pF, VIH= VIT+max + 0.2 V, VIL= VIT-min - 0.2 V, 9 01 7 s tPHL2RESIN = 2.7 V, VDD= 5.0 V, CONTROL = 0.4 V, CT= NC, see figure 4 4/ 24 Propagation delay time, RESIN to RESET tPLH3RL= 2 k, CL= 50 pF, VIH= 2.7 V, VDD
39、= 5.0 V, VIL= 0.4 V, 9 01 24 s tPHL3SENSE = VIT+max + 0.2 V, CONTROL = 0.4 V, CT= NC, see figure 4 4/ 60 ns Propagation delay time, RESIN to RESET tPLH4RL= 2 k, CL= 50 pF, VIH= 2.7 V, VDD= 5.0 V, VIL= 0.4 V, 9 01 65 ns tPHL4SENSE = VIT+max + 0.2 V, CONTROL = 0.4 V, CT= NC, see figure 4 4/ 24 s See f
40、ootnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97513 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance c
41、haracteristics - Continued. Test Symbol Conditions 1/ -55C TA +125C +2.0 V VDD +6.0 V Group A subgroups Device type Limits Unit unless otherwise specified Min Max Propagation delay time, CONTROL to RESET tPLH5RL= 2 k, CL= 50 pF, VIH= 2.7 V, VDD= 5.0 V, VIL= 0.4 V, 9 01 58 ns tPHL5SENSE = VIT+max + 0
42、.2 V, RESIN = 2.7 V, CT= NC, see figure 4 4/ 58 Low-level minimum pulse duration from SENSE tWVIH= VITmax+ 0.2 V VIL= VITmin- 0.2 V 9 01 3 s Low-level minimum pulse duration from RESIN tWVIL= 0.4 V, VIH= 2.7 V 9 01 1 s 1/ All characteristics are measured with CT= 0.1 F. 2/ To ensure best stability o
43、f the threshold voltage, a bypass capacitor (ceramic, 0.1 F) should be placed near the supply terminals. 3/ The lowest supply voltage at which RESET becomes active. 4/ NC equals no capacitor and includes up to 100 pF probe and jig capacitance. 3.5.1 Certification/compliance mark. The certification m
44、ark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-385
45、35 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of complia
46、nce submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A
47、 and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. Provided by IHSNot for ResaleNo reproductio
48、n or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97513 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outlines H P 2 Terminal number Terminal symbol 1 NC CONTROL NC 2 CONTROL RESIN CONTROL 3 RESIN CT NC4 CT GND NC 5 GND RESET RESIN 6 RESET RESET NC 7 RESET SENSE CT 8 SENSE VDDNC 9 VDD- NC 10 NC - GND 11 - - NC 12 - - RESET 13 - - NC 14 - - NC 15 - - RESET 16 -
