1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add VINtest conditions for VOHand VOLin table I. Add table III, delta limits. Update boilerplate to the MIL-PRF-38535 requirements. Editorial changes throughout. jak 03-05-02 Thomas M. Hess B Update boilerplate paragraphs to the current MIL-PRF-3
2、8535 requirements. - LTG 10-11-22 Thomas M. Hess REV SHET REV B B B B SHEET 15 16 17 18 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Joseph A. Kerby DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MIC
3、ROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE AMSC N/A CHECKED BY Charles F. Saffle, Jr. APPROVED BY Monica L. Poelking MICROCIRCUIT, DIGITAL, ADVANCED BIPOLAR CMOS, 3.3 VOLT 16-BIT EDGE-TRIGGERED D-TYPE FLIP FLOP WITH BUS HOLD, EQUI
4、VALENT 22 SERIES OUTPUT RESISTORS WITH THREE-STATE OUTPUTS AND TTL COMPATIBLE INPUTS, MONOLITHIC SILICON DRAWING APPROVAL DATE 98-03-25 REVISION LEVEL B SIZE A CAGE CODE 67268 5962-98542 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E060-11 Provided by IHSNot for ResaleNo reproduction or networking permi
5、tted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98542 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classe
6、s Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the f
7、ollowing example: 5962 - 98542 01 V X A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Leadfinish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-
8、PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device typ
9、e(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54LVTH162374 3.3 V 16-bit edge-triggered D-type flip-flop with bus hold, equivalent 22 series resistors, three-state outputs, and TTL compatible inputs 1.2.3 Device class designator. The device class design
10、ator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification
11、and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X GDFP1-F48 48 Flat pack1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes
12、 Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98542 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1
13、.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) -0.5 V dc to +4.6 V dc DC input voltage range (VIN) -0.5 V dc to +7.0 V dc 4/ Voltage range applied to any output in the high or power-off state (VOUT) . -0.5 V dc to 7.0 V dc 4/ Current into any output in the low state (IOL) 30 mA Cur
14、rent into any output in the high state (IOH) 30 mA 5/ Input clamp current (IIK) (VINVCC. 6/ The maximum package power dissipation is calculated using a junction temperature at 150C and a board trace length of 750 mils. 7/ Unused inputs must be held high or low to prevent them from floating. Provided
15、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98542 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, an
16、d handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Cir
17、cuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780
18、 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between th
19、e text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for
20、device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for devi
21、ce class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and
22、V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3
23、.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce test circuit and waveforms. The ground bounce test circuit and waveforms shall be as specified on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as sp
24、ecified on figure 5. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperatur
25、e range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIR
26、CUIT DRAWING SIZE A 5962-98542 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD P
27、IN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device
28、class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A.
29、3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufactur
30、er in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q a
31、nd V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A
32、shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that aff
33、ects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made av
34、ailable onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 127 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or networking permitted without
35、 license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98542 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +2.7 V VCC
36、 +3.6 V unless otherwise specified VCCGroup A subgroups Limits 3/ Unit Min Max Negative input clamp voltage 3022 VIKFor input under test IIN= -18 mA 2.7 V 1, 2, 3 -1.2 V High level output voltage 3006 VOHFor all inputs affecting output under test VIN= VIH = 2.0 V or VIL= 0.8 V IOH= -12 mA 3.0 V 1, 2
37、, 3 2.0 V Low level output voltage 3007 VOLFor all inputs affecting output under test VIN= VIH = 2.0 V or VIL= 0.8 V IOL= 12 mA 3.0 V 1, 2, 3 0.8 V Input current high 3010 IIHFor input under test, VIN= 5.5 V 0.0 V and 3.6 V 1, 2, 3 10.0 A For control inputs under test VIN= VCC3.6 V 1.0 For data inpu
38、ts under test VIN= VCC1.0 Input current low 3009 IILFor control inputs under test VIN= GND 3.6 V 1, 2, 3 -1.0 A For data input under test VIN= 0.0 V -5.0 Input bus hold current IIN(hold)Data inputs VIN= 0.8 V 3.0 V 1, 2, 3 75.0 A VIN= 2.0 V -75.0 Three-state output leakage current high 3021 IOZHVOUT
39、= 3.0 V 3.6 V 1, 2, 3 5.0 A Three-state output leakage current low 3020 IOZLVOUT= 0.5 V 3.6 V 1, 2, 3 -5.0 A Three-state output current, power-up IOZPU4/ VOUT= 0.5 V to 3.0 V mOE = Dont care 0.0 V to 1.5 V 1, 2, 3 100 A Three-state output current, power-down IOZPD4/ VOUT= 0.5 V to 3.0 V mOE = Dont c
40、are 1.5 V to 0.0 V 1, 2, 3 100 A Quiescent supply current 3005 ICCVIN= VCCor GND IOUT= 0.0 A Outputs high 3.6 V 1, 2, 3 0.19 mA Outputs low 5.0 Outputs disabled 0.19 Quiescent supply current delta, TTL input levels 3005 ICC 5/ One input at VCC - 0.6 V Other inputs at VCCor GND 3.0 V and 3.6 V 1, 2,
41、3 0.2 mA See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98542 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical
42、 performance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +2.7 V VCC +3.6 V unless otherwise specified VCCGroup A subgroups Limits 3/ Unit Min Max Input capacitance 3012 CINTC= +25C See 4.4.1c 0.0 V and 3.6 V 4 12.0 pF Output capacitance 30
43、12 COUTTC= +25C See 4.4.1c 0.0 V and 3.6 V 4 15.0 pF Low level ground bounce noise VOLP6/ VIH= 2.7 V,VIL= 0.0 V TA= +25C See 4.4.1d See figure 4 3.0 V 4 450 mV VOLV6/ 3.0 V 4 -350 mV High level VCC bounce noise VOHP6/ 3.0 V 4 650 mV VOHV6/ 3.0 V 4 -1000 mV Functional test 3014 7/ VIN= VIHor VILVerif
44、y output VOUTSee 4.4.1b 2.7 V and 3.6 V 7, 8 L H Clock frequency f clockCL= 50 pF minimum RL= 500 3.0 V and 3.6 V 9, 10,11 0.0 160.0 MHz 2.7 V0.0 160.0 Pulse duration, mCLK high or low twCL= 50 pF minimum RL= 500 See figure 5 3.0 V and 3.6 V 9, 10,11 3.0 ns 2.7 V 3.3 Setup time, data before mCLK tsu
45、CL= 50 pF minimum RL= 500 See figure 5 3.0 V and 3.6 V9, 10,11 2.8 ns 2.7 V 3.2 Hold time, data after mCLK thCL= 50 pF minimum RL= 500 See figure 5 3.0 V and 3.6 V 9, 10,11 1.2 ns 2.7 V 0.5 Maximum clock frequency f MAXCL= 50 pF minimum RL= 500 See figure 5 3.0 V and 3.6 V 9, 10,11 160.0 MHz 2.7 V 1
46、60.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98542 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electrical per
47、formance characteristics - Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ -55C TC +125C +2.7 V VCC +3.6 V unless otherwise specified VCCGroup A subgroups Limits 3/ Unit Min Max Propagation delay time, mCLK to mQn 3003 tPLH 8/ CL= 50 pF minimum RL= 500 See figure 5 3.0 V and
48、 3.6 V 9,10,11 1.4 6.6 ns 2.7 V 7.4 tPHL 8/ 3.0 V and 3.6 V 9,10,11 1.4 5.8 2.7 V 6.0 Propagation delay time, output enable, mOE to mQn 3003 tPZH8/ CL= 50 pF minimum RL= 500 See figure 5 3.0 V and 3.6 V 9,10,11 1.0 6.6 ns 2.7 V 7.4 tPZL8/ 3.0 V and 3.6 V 9,10,11 1.4 6.0 2.7 V 6.8 Propagation delay time, output disable, mOE to mQn 3003 tPHZ8/ CL= 50 pF minimum RL= 500 See figure 5 3.0 V and 3.6 V 9,10,11 1.0 6.6 ns 2.7 V 7.4 tPLZ8/ 3.0 V and 3.6 V 9,10,11 1.4 6.0 2.7 V 6.0 See footnotes on next sheet. Provided by IHSNot for ResaleNo reproduction
