1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update drawing to reflect current requirements. 05-01-25 Raymond Monnin B Add case outline X. Figure 2, case outline T, correct terminal symbol for terminal number 2 from no connection to output. -gz 10-04-15 Charles F. Saffle C Updated drawing p
2、aragraphs. -sld 12-05-15 Charles F. Saffle REV SHEET REV SHEET REV STATUS REV C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 PMIC N/A PREPARED BY Gary Zahn DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil/ STANDARD MICROCIRCUIT DRAWING CHECKED BY Michael C.
3、 Jones THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE APPROVED BY Kendall A. Cottongim MICROCIRCUIT, LINEAR, VOLTAGE REGULATOR, POSITIVE, ADJUSTABLE, LOW DROPOUT, MONOLITHIC SILICON DRAWING APPROVAL DATE 99-07-14 AMSC N/A REVISION LEVEL C SIZE A CAGE C
4、ODE 67268 5962-98647 SHEET 1 OF 10 DSCC FORM 2233 APR 97 5962-E171-12Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98647 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 22
5、34 APR 97 1. SCOPE 1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardne
6、ss assurance levels are reflected in the PIN. 1.2 PIN. The PIN shall be as shown in the following example: 5962 - 98647 01 H T A Federal RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) /
7、Drawing number 1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type. The device type identify the circuit function as
8、 follows: Device type Generic number 1/ Circuit function 01 SDP1083 7.5 A, positive voltage regulator, adjustable, low dropout 1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All levels are defined by the requirements of M
9、IL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and E) or QML Listing (Class G and D). The product assurance levels are as follows: Device class Device performance documentation K Highest reliability class available. This level is intended for use in space applicatio
10、ns. H Standard military quality class level. This level is intended for use in applications where non-space high reliability devices are required. G Reduced testing version of the standard military quality class. This level uses the Class H screening and In-Process Inspections with a possible limite
11、d temperature range, manufacturer specified incoming flow, and the manufacturer guarantees (but may not test) periodic and conformance inspections (Group A, B, C, and D). E Designates devices which are based upon one of the other classes (K, H, or G) with exception(s) taken to the requirements of th
12、at class. These exception(s) must be specified in the device acquisition document; therefore the acquisition document should be reviewed to ensure that the exception(s) taken will not adversely affect system performance. D Manufacturer specified quality class. Quality level is defined by the manufac
13、turers internal, QML certified flow. This product may have a limited temperature range. 1/ The SDP1083 is similar to the LT1083 or OM183 or OM1830 listed on Standard Microcircuit Drawing 5962-89520.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STAN
14、DARD MICROCIRCUIT DRAWING SIZE A 5962-98647 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.2.4 Case outlines. The case outlines are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style N See figu
15、re 1 3 Z-tab with nonisolated tab, (TO-259), with glass seal T See figure 1 3 Flange mount with nonisolated tab, (TO-258), with glass seal U See figure 1 3 Flange mount with isolated tab, (TO-258), with glass seal X See figure 1 3 Flange mount with nonisolated tab, (TO-258), with ceramic seal Z See
16、figure 1 3 Z-tab with isolated tab, (TO-259), with glass seal 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534. 1.3 Absolute maximum ratings. 1/ Input to output voltage differential 35 V dc Output current (IOUT) 7.5 A Storage temperature range -65 C to +150 C Lead temperatur
17、e (soldering, 10 seconds) +300 C Junction temperature (TJ) +150 C Power dissipation (PD) . Internally limited Thermal resistance, junction-to-case (qJC): Case N, T, and X 1.6 C/W Case U and Z . 2.75 C/W Thermal resistance, junction-to-ambient (qJA) 30 C/W 1.4 Recommended operating conditions. Input
18、to output voltage differential 25 V dc Output current (IOUT) 10 mA minimum Full load current (IFL) . 5.0 A Ambient operating temperature range(TA) . -55 C to +125 C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks f
19、orm a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38534 - Hybrid Microcircuits, General Specification for. DEPARTMENT OF DEFENSE STANDARDS M
20、IL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines. 1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability.
21、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98647 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Sta
22、ndard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of preceden
23、ce. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requiremen
24、ts. The individual item performance requirements for device classes D, E, G, H, and K shall be in accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as designated in the device manufacturers Quality Management (QM) plan or as designated
25、for the applicable device class. The manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not affect the form,
26、 fit, or function of the device for the applicable device class. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38534 and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein and
27、 figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full specified operating t
28、emperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking of devices. Marking of devices shall be in accordance with MIL-PRF-38534. The device shall be
29、marked with the PIN listed in 1.2 herein. In addition, the manufacturers vendor similar PIN may also be marked. 3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described herein shall maintain the electrical test data (variables format) f
30、rom the initial quality conformance inspection group A lot sample, for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those which, if any, are guaranteed. This data shall be maintained under document revision level control by the ma
31、nufacturer and be made available to the preparing activity (DLA Land and Maritime -VA) upon request. 3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this drawing. The certificate of compliance (original copy) submitted to DLA Lan
32、d and Maritime -VA shall affirm that the manufacturers product meets the performance requirements of MIL-PRF-38534 and herein. 3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of microcircuits delivered to this drawing. Provide
33、d by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98647 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Condi
34、tions -55 C TA+125 C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Reference voltage VREF(VIN- VOUT) = 3.0 V, IOUT= 10 mA 1 01 1.238 1.262 V 1.5 V (VIN- VOUT) 25 V, 10 mA IOUT 5.0 A 1,2,3 1.220 1.270 Line regulation 1/ INOUTVVDD1.5 V (VIN- VOUT) 15 V, IOUT= 10 mA 1 01
35、0.2 % 1.5 V (VIN- VOUT) 35 V, IOUT= 10 mA 2,3 0.5 Load regulation 1/ OUTOUTIVDD(VIN- VOUT) = 3.0 V, 10 mA IOUT 5.0 A 1 01 0.3 % 2,3 0.4 Dropout voltage VDOIOUT= 5.0 A, DVREF= 1.0% 1,2,3 01 1.5 V Thermal regulation - - - 30 ms pulse, TA= +25 C 1 01 0.01 %/W Ripple rejection OUTINVVDDf = 120 Hz, CADJ=
36、 25 mF, COUT= 25 mF (tantalum), IOUT= 5.0 A, (VIN- VOUT) = 3.0 V 4,5,6 01 60 dB Adjust pin current IADJ1.5 V (VIN- VOUT) 25 V, 10 mA IOUT 5.0 A 1,2,3 01 120 mA Adjust pin current change DIADJ1.5 V (VIN- VOUT) 25 V, 10 mA IOUT 5.0 A 1,2,3 01 5.0 mA Minimum load current IMIN(VIN- VOUT) = 25 V 1,2,3 01
37、 10 mA Current limit ILIM(VIN- VOUT) = 5.0 V 1,2,3 01 8.0 A (VIN- VOUT) = 25 V 0.4 Temperature stability 2/ DVOUT-55 C TJ +125 C 1,2,3 01 1.5 % Long term stability 2/ DVOUTt =1000 hrs, TA= +125 C 2 01 1.0 % 1/ Line and load regulation are measured at a constant junction temperature using a low duty
38、cycle pulse technique. Although power dissipation is internally limited, regulation is guaranteed up to the maximum power dissipation of 60 W. Power dissipation is determined by the input/output differential voltage and the output current. Guaranteed maximum power dissipation will not be available o
39、ver the full input/output voltage range. 2/ If not tested, shall be guaranteed to the limits specified in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98647 DLA LAND AND MARITIME COLUMBUS, OHIO 43
40、218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 Case outlines T, U, and X. Inches mm .005 0.13 .010 0.25 .020 0.51 Symbol Millimeters Inches Min Max Min Max A 6.10 6.86 .240 .270 A1 0.89 1.14 .035 .045 A2 3.56 BSC .140 BSC b 1.40 1.65 .055 .065 D 20.70 21.21 .815 .835 D1 13.46 13.97 .530 .55
41、0 D3 0.00 2.34 .000 .092 e 5.08 BSC .200 BSC E 17.40 17.65 .685 .695 L 12.70 19.05 .500 .750 O 17.70 17.96 .697 .707 P 3.94 4.19 .155 .165 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, this item was originally designed using inch-pound units of measureme
42、nt. In the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outlines. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98647 DLA LAND AND MA
43、RITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 Case outlines N and Z. Symbol Millimeters Inches Min Max Min Max A 30.10 30.35 1.185 1.195 A1 17.40 17.65 .685 .695 A2 6.22 6.48 .245 .255 A3/L3 3.18 BSC .125 BSC b 1.40 1.65 .055 .065 D 6.10 6.86 .240 .270 D1 3.56 BSC .
44、140 BSC D2 0.89 1.14 .035 .045 e 5.08 BSC .200 BSC L 13.46 13.97 .530 .550 L1 12.70 19.05 .500 .750 L2 6.22 6.48 .245 .255 P 3.05 3.30 .120 .130 NOTE: The U.S. government preferred system of measurement is the metric SI system. However, this item was originally designed using inch-pound units of mea
45、surement. In the event of conflict between the metric and inch-pound units, the inch-pound units shall take precedence. FIGURE 1. Case outlines - Continued. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-986
46、47 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Device type 01 Case outlines N (nonisolated tab) T and X (nonisolated tab) U and Z (isolated tab) Terminal number Terminal symbol Terminal symbol Terminal symbol 1 2 3 Tab Adjust No connection Input Out
47、put Adjust Output Input Output Adjust Output Input No connection FIGURE 2. Terminal connections.Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-98647 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION L
48、EVEL C SHEET 9 DSCC FORM 2234 APR 97 TABLE II. Electrical test requirements. MIL-PRF-38534 test requirements Subgroups (in accordance with MIL-PRF-38534, group A test table) Interim electrical parameters 1 Final electrical parameters 1*, 2, 3, 4, 5, 6 Group A test requirements 1, 2, 3, 4, 5, 6 Group C end-point electrical parameters 1, 2, 3 End-point electrical parameters for
