DOD A-A-51810-1987 TIMER INTERVAL《间歇时间》.pdf

上传人:赵齐羽 文档编号:701645 上传时间:2019-01-01 格式:PDF 页数:3 大小:149.07KB
下载 相关 举报
DOD A-A-51810-1987 TIMER INTERVAL《间歇时间》.pdf_第1页
第1页 / 共3页
DOD A-A-51810-1987 TIMER INTERVAL《间歇时间》.pdf_第2页
第2页 / 共3页
DOD A-A-51810-1987 TIMER INTERVAL《间歇时间》.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 A-A-5LLO 66 W 7777774 OOLOO7 b M tLC,d/r- / A-A- 5 18 10 4 February 1987 COMMERCIAL ITEM DESCRIPTION TIMER, INTERVAL The General Services Administration has authorized the use of this commercial item description. This commercial item description covers one type of interval timer for laboratory use

2、 Salient characteristics: Shall be an electrically powered, four-channel timer controlled by a quartz crystal for accuracy consisting of three countdown timing channels and a fourth channel which shall display the time of day. The countdown timing channels shall be capable of being set from 20 hour

3、s to one second. Each channel shall have a distinct tone and visible alarm which sounds and blinks until it has been shut off. Channel displays shall be 13 millimeter high LED display digits and shall operate on 120 volts A.C. at a frequency of 60 Hertz. The unit shall be approximately 2 inches (5.0

4、 cm) high by 7 inches (17.5 cm.) wide by 4 inches (10.0 cm.1 deep and housed in an ABS plastic case. Each unit shall have operating instructions which are neat and legible. Shall be in conformance with Under- writers Laboratory Standard 1222. Workmanship. The interval timer shall be free from defect

5、s which detract from its appearance or impair its serviceability. Unit. Each (EA). One interval timer as specified, constitutes one unit. Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance f all inspection re

6、quirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to p

7、erform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. AMSC N/A FSC 6645 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. 1 of 3 Provided by IHSNot f

8、or ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A- 5 1 8 1 O Records. Records of examinations and tests performed by or for the contractor shall be maintained by the contractor and made available to the Government upon the Governments request, at any time, or from tim

9、e to time, during the performance of the contract and for a period of three years after delivery of the supplies to which such records relate. Inspections. Inspections, as used herein, is defined as both examination (such as visual or auditory investigation without the use of special laboratory appl

10、iances or procedures) and testing (determination by technical means of physical and chemical properties) of the item, Samplinq for inspection. Sampling for inspection shall be conducted in accordance with MIL-STD-105. Where feasible, the same sample shall be used for the determination of two or more

11、 inspection character- istics* Unless otherwise specified, sampling for examination shall be conducted at inspection level S-2, AQL 2.5, and sampling for tests (when applicable) shall be conducted at inspection level 8-3, AQL 1.0. Tests. Tests shall be conducted to determine compliance with specific

12、ation requirements. Where feasible, the same sample shall be used for the determination of two or more test characteristics. Contractor certification. The contractor shall certify that the product offered meets the salient characteristics of this description and conforms to the producers own drawing

13、s, specifications, standards, and quality assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Regulatory requirements. If the product covered by this

14、document has been determined by the U.S. Food and Drug Administration to be under its jurisdiction, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of the Federal Food, Drug and Cosmetic Act, as amended, and regulations pr

15、omulgated thereunder. In addition, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of all other applicable Federal, State, and local statutes, ordinances, and regulations. Federal Food, Drug and Cosmetic Act. 2 Provided by

16、 IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-SLLO bb M 7777774 OOLOBLL Li A-A- 5 18 10 Recovered materials. The offeror/contractor is encouraged to use recovered material in accordance with Public Law 94-580 to the maximum extent practical. Preservation,

17、 packaqing, packing, labeling, and marking. Unless otherwise specified, preservation, packaging, and packing shall be to a degree of protection to preclude damage to containers and/or contents thereof under normal shipping conditions, handling, etc:, involving shipment from-the supply source to the

18、receiving activity, plus reshipment from receiving activity, and shall conform to applicable carriers rules and regulations. package quantities and labeling and marking shall be as specified in the contract and/or order. Intermediate and exterior For information only. The following National Stock Nu

19、mber is covered by this document: 6645-01-212-9474 TIMER, INTERVAL Ordering data. and marking must be specified in the contract and/or order). (Intermediate/exterior package quantities and labeling MILITARY INTERESTS: Custodians: Army - MD Navy - MS Air Force - 03 CIVIL AGENCY COORDINATING ACTIVITY: VA - OSS PREPARING ACTIVITY: DoD-MB Agent: DLA-DM Project No. 6645-0375 CID-timer-interval-9474 3 U.1. I0VCIII)ILNT ?RKNTIN1 OFFXCE: 1117 - 704-01117OJOO Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-

展开阅读全文
相关资源
猜你喜欢
  • BS ISO 16243-2011 Surface chemical analysis Recording and reporting data in X-ray photoelectron spectroscopy (XPS)《表面化学分析 X射线光电子能谱术(XPS)的记录和报告数据》.pdf BS ISO 16243-2011 Surface chemical analysis Recording and reporting data in X-ray photoelectron spectroscopy (XPS)《表面化学分析 X射线光电子能谱术(XPS)的记录和报告数据》.pdf
  • BS ISO 16247-2006 Road vehicles - Detection of exhaust systems leaks - Helium test method and detection device specification《道路车辆 排气系统泄漏的检测 氦试验方法和探测装置规范》.pdf BS ISO 16247-2006 Road vehicles - Detection of exhaust systems leaks - Helium test method and detection device specification《道路车辆 排气系统泄漏的检测 氦试验方法和探测装置规范》.pdf
  • BS ISO 16249-2013 Springs Symbols《弹簧 符号》.pdf BS ISO 16249-2013 Springs Symbols《弹簧 符号》.pdf
  • BS ISO 16254-2016 Acoustics Measurement of sound emitted by road vehicles of category M and N at standstill and low speed operation Engineering method《声学 M类和N类道路车辆在停放和低速操作时发出噪声的测量 .pdf BS ISO 16254-2016 Acoustics Measurement of sound emitted by road vehicles of category M and N at standstill and low speed operation Engineering method《声学 M类和N类道路车辆在停放和低速操作时发出噪声的测量 .pdf
  • BS ISO 16258-1-2015 Workplace air Analysis of respirable crystalline silica by X-ray diffraction Direct-on-filter method《工作场所空气 使用X射线衍射法分析可吸入石英 直接过滤法》.pdf BS ISO 16258-1-2015 Workplace air Analysis of respirable crystalline silica by X-ray diffraction Direct-on-filter method《工作场所空气 使用X射线衍射法分析可吸入石英 直接过滤法》.pdf
  • BS ISO 16258-2-2015 Workplace air Analysis of respirable crystalline silica by X-ray diffraction Method by indirect analysis《工作场所空气 使用X射线衍射法分析可吸入石英 间接分析法》.pdf BS ISO 16258-2-2015 Workplace air Analysis of respirable crystalline silica by X-ray diffraction Method by indirect analysis《工作场所空气 使用X射线衍射法分析可吸入石英 间接分析法》.pdf
  • BS ISO 16260-2016 Paper and board Determination of internal bond strength《纸和纸板 内部粘结强度的测定》.pdf BS ISO 16260-2016 Paper and board Determination of internal bond strength《纸和纸板 内部粘结强度的测定》.pdf
  • BS ISO 16269-4-2010 Statistical interpretation of data Detection and treatment of outliers《数据的统计说明 异常值的检测和处理》.pdf BS ISO 16269-4-2010 Statistical interpretation of data Detection and treatment of outliers《数据的统计说明 异常值的检测和处理》.pdf
  • BS ISO 16269-6-2014 Statistical interpretation of data Determination of statistical tolerance intervals《数据统计说明 统计公差区间的测定》.pdf BS ISO 16269-6-2014 Statistical interpretation of data Determination of statistical tolerance intervals《数据统计说明 统计公差区间的测定》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1