DS ISO 2934-1989 Modular units for machine tool construction Wing base for columns《机床结构的组合件》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DIN 9003-1-1984 Aerospace bending of sheets plates and strips of steel and heat-resisting alloys bending radii directions for design《航空航天 钢制和耐热合金的薄板、板材和带材的弯曲、弯曲半径、设计指导说明》.pdf

DIN 9003-3-1994 Aerospace - Bending of light metal sheets and strips - Part 3 Bending radii directions for design《航空航天 轻金属板材和带材的弯曲 第3部分 弯曲半径 设计说明》.pdf

DIN 9003-5-1986 Aerospace bending of light metal sheet and strip dimensions limit deviations and compensation values《航空航天 轻金属薄板材和带材的弯曲 尺寸、极限偏差、补偿值》.pdf

DIN 9003-6-1992 Aerospace bending of sheet and strip stop-drill holes corner configurations《航空航天 薄板材和带材的弯曲 钻头孔 角结构》.pdf

DIN 9004-1985 Aerospace bending radii for tubes approximate values for cold working《航空航天 管弯曲半径 冷加工用近似值》.pdf

DIN 9015-1-1986 Aerospace ISO-fits for airframe construction (except mounting of roller bearings)《航空航天 飞机结构的ISO配合(滚柱轴承的安装除外)》.pdf

DIN 9015-2-1986 Aerospace ISO-fits for engine construction (except mounting of roller bearings)《航空航天 发动机结构的ISO配合(滚柱轴承的安装除外)》.pdf

DIN 9020-1-1983 Aerospace mass breakdown for aircraft heavier than air main mass groups and terms of mass survey《航空航天 比空气重的飞机的质量分解 主要质量组和质量术语 一般说明》.pdf

DIN 9020-2-1983 Aerospace mass breakdown for aircraft heavier than air main mass groups and terms of mass definitions《航空航天 比空气重的飞行器的质量分解 质量的主要分组与质量术语、定义》.pdf