DS ISO 811-1982 Textile fabrics Determination of resistance to water penetration Hydrostatic pressure test《织物 耐水渗透性的测定 静水压试验》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

DS ISO 5725-1-1995 Accuracy (trueness and precision) of measurement methods and results- Part 1 General principles and definitions《测量方法和测量结果的精确度（真实性和准确性） 第1部分：一般原则和定义》.pdf

DS ISO 5725-2-1995 Accuracy (trueness and precision) of measurement methods and results - Part 2 Basic method for the determination of repeatability and reproducibility of a standa.pdf

DS ISO 5725-4-1995 Accuracy (trueness and precision) of measurement methods and results - Part 4 Basic methods for the determination of the trueness of a standard measurement metho.pdf

DS ISO 5725-6-1995 Accuracy (trueness and precision) of measurement methods and results - Part 6 Use in practice of accuracy values《测量方法和测量结果的精确度（真实性和准确性） 第6部分：实践中精确值的使用》.pdf

DS ISO 5784-1-1989 Fluid power systems and components Fluid logic circuits Part 1 Symbols for binary logic and related functions《流体动力系统和组件 流体的逻辑回路 第1部分 二进制逻辑和有关功能的符号》.pdf

DS ISO 5864-1995 ISO inch screw threads - Allowances and tolerances《ISO 英制螺纹 允差和公差》.pdf

DS ISO 594-1-1989 Conical fittings with a 6% (Luer) taper for syringes needles and certain other medical equipment Part 1 General requirements《注射器、针头和某些其它医用设备的有6% 锥度的锥形配件 第1部分 一般要求.pdf

DS ISO 6123 1-1983 Rubber or plastic covered rollers Specifications Part 1 Requirements for hardness《橡胶或塑料包覆的辊筒 规范 第1部分 硬度要术》.pdf

DS ISO 6123 3-1986 Rubber- or plastic-covered rollers Specifications Part 3 Dimensional tolerances《橡胶或塑料包覆的辊筒 规范 第3部分 尺寸公差》.pdf