ECA EIA-296-F-2000 Lead Taping of Components in Axial Lead Configuration for Automatic Handling《自动装配用轴向配置元件的引线带式封装》.pdf
《ECA EIA-296-F-2000 Lead Taping of Components in Axial Lead Configuration for Automatic Handling《自动装配用轴向配置元件的引线带式封装》.pdf》由会员分享,可在线阅读,更多相关《ECA EIA-296-F-2000 Lead Taping of Components in Axial Lead Configuration for Automatic Handling《自动装配用轴向配置元件的引线带式封装》.pdf(14页珍藏版)》请在麦多课文档分享上搜索。
1、 EIA STANDARD Lead Taping of Components in Axial Lead Configuration for Automatic Handling EIA-296-F March 2015 ANSI/EIA-296-F(2015) Approved: March 27, 2015 EIA-296-F NOTICE EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings be
2、tween manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any me
3、mber or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than ECIA members, whether the standard is to be used either domestically or inte
4、rnationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Public
5、ation. This EIA Standard is considered to have International Standardization implication, but the International Electrotechnical Commission activity has not progressed to the point where a valid comparison between the EIA Standard and the IEC document can be made. This Standard does not purport to a
6、ddress all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Propos
7、al No. 4518, formulated under the cognizance of the National Standards Committee for Automated Component Handling and reaffirmed under Standards Project Number 5319). Published by Electronic Components Industry Association 2015 Standards Table 1 and associated paragraphs 5.1 through 5.10. 4.2 Reelin
8、g and optional fan fold packaging of taped axial leaded components are defined in Figure 2, Table 2 and associated paragraphs 6.1 through 6.4. 4.3 Dimensions contained in this Standard are expressed in metric terms with English equivalents. Metric dimensions shall govern. EIA-296-F Page 2 4.4 Procur
9、ement documents and quotation requests should include the following minimum information: (a) Reference to this Standard by title and number. (b) Inside tape spacing and component pitch. (c) Taping quality requirements including maximum number of missing parts if different than Paragraph 5.7. (d) Ree
10、l or Fan Fold packaging (e) Container and reel marking requirements if different than specified in paragraph 6.2 of this document. EIA-296-F Page 3 5.0 LEAD TAPING REQUIREMENTS FIGURE 1W L3 T H A M S P B L1 L2 W L3 L1 L2A H P T M B S EIA-296-F Page 4 TABLE 1 EIA-296-F Page 5 5.1 Leads shall not be b
11、ent beyond 1.0mm (.039) for “B“ dimension of 26mm or 1.2mm (.047) for all other “B“ dimensions from their nominal position when measured between the center line of the component lead at the inside tape edge and the center line of the lead egress from the component. 5.2 Splicing tapes or clips are pe
12、rmissible provided they do not degrade the strength or handling characteristics of the taped component. Staples shall not be used. The splicing tapes shall be of equal strength to the original tape and shall overlap a minimum of 50.8mm (2.0) in each direction of the break in the tape being joined. T
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ECAEIA296F2000LEADTAPINGOFCOMPONENTSINAXIALLEADCONFIGURATIONFORAUTOMATICHANDLING 自动 装配 轴向 配置 元件 引线 封装

链接地址:http://www.mydoc123.com/p-704170.html