1、 EIA STANDARD TP-02D Air Leakage Test Procedure for Electrical Connectors EIA-364-02D (Revision of EIA-364-02C) April 2012 Electronic Components Industry Association EIA-364-02D ANSI/EIA-364-02D-2012(R2017) Approved: April 10, 2012 Reaffirmed: August 18, 2017 NOTICE EIA Engineering Standards and Pub
2、lications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular
3、 need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by t
4、hose other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent
5、owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This standard is based upon the major technical content of International Electrotechnical Commission standard 60512-14-4 (was 512-7, test 14d), immersion, waterproof, 2006-03. It conforms in all essent
6、ial respects this IEC standard. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicabili
7、ty of regulatory limitations before its use. (From Standards Proposal No. SP-5393.01 formulated under the cognizance of the CE-2.0 National Connector Standards Committee). Published by Electronic Components Industry Association 2017 EIA Standards see 4.1 5.2 Full description of test specimen; see 3.
8、1 5.3 Manner in that specimen is to be prepared; see 3 5.4 Pressure differential required; see 2.1.1.2 5.5 Test specimen orientation and whether reverse testing is also required; see 4.5 5.6 Maximum allowable leakage rate; see 4.4 EIA-364-02D Page 6 6 6 Test documentation Documentation shall contain
9、 the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Description of test specimen including fixturing, if applicable 6.3 Test equipment used, and date of last and next calibration 6.4 Test procedure used 6.5 Values and observations 6.5.1 Initial and final
10、 conditions 6.5.2 Leakage rate observed, comparison to connector specification requirements, whether specimens passed or failed 6.6 Name of operator and start/finish date(s) of test ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for sa
11、fety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Association Technology Strategy & Standards Department Publications Office 2214 Rock Hill Road, Suite 170 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Documen
12、t Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Commit
13、tee: Chairman: Date comments forwarded to Committee Chairman: Revision History Revision letter Project number Additions, changes and deletions D SP-5227 Revised format to comply with current practices in conjunction with 5 year review. Revision contains no technical changes. Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org
