1、 EIA STANDARD TP-104B Flammability Test Procedure for Electrical Connectors EIA-364-104B (Revision of EIA-364-104A) September 2015 Electronic Components Industry Association EIA-364-104B ANSI/EIA-364-104B-2015 Approved: September 3, 2015 NOTICE EIA Engineering Standards and Publications are designed
2、 to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of su
3、ch Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than ECIA m
4、embers, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it ass
5、ume any obligation whatever to parties adopting the Standard or Publication. This standard is based upon the major technical content of International Electrotechnical Commission standard 60512-20-1 (was IEC 512-9, test 20a), flammability, needle-flame, 2010-06, first edition. It conforms in all esse
6、ntial respects this IEC standard. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicabi
7、lity of regulatory limitations before its use. (From Standards Proposal No. 5347.04 formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Sockets Standards.) Published by Electronic Components Industry Association 2015 EIA Standards see Figure 1. Table 1 - Test condit
8、ions Condition Flame height Flame application time, seconds Number of applications of flame A 38 mm (1.50 in) 60 1 B 38 mm (1.50 in) 30 1 C 19 mm (0.75 in) 10 1 4.6 Unless otherwise specified, the following shall be the criteria for failure: 4.6.1 Burning after removal of applied flame shall extingu
9、ish within the time specified in Table 2. 4.6.2 After-glow shall extinguish within time specified in Table 2 after burning ceases. 4.6.3 There shall be no dripping that shall cause the flammable material to ignite. 4.6.4 There shall be no violent burning or explosive type fire. Table 2 - Flame and a
10、fter-glow extinguishing time Conditions Flame extinguishing time, seconds After-glow extinguishing time, seconds A 3 3 B 15 15 C Flame extinguish time plus after-glow extinguish time shall be less than or equal to 30 seconds EIA-364-104B Page 4 5 Details to be specified The following details shall b
11、e specified in the referencing document: 5.1 Test condition from Table1; see 4.5 5.2 Flame and after-glow extinguishing time, if other than the time specified in Table 2; see 4.6 6 Documentation Documentation shall contain the details specified in clause 5 (when provided), and the following: 6.1 Tit
12、le of test 6.2 Test condition and results of test procedure; see Table 1 6.3 Values and observations 6.3.1 Time in seconds of burning of visible flame on the specimen after removal of applied flame 6.3.2 Time in seconds of after-glow after extinction of flame 6.3.3 Any dripping or falling of particl
13、es (burning or not burning) onto the flammable material or ignition of the flammable material 6.3.4 Any violent explosion, sputtering, or other unusual type burning 6.4 Name of operator and date of test EIA-364-104B Page 5 Figure 1 - Flammability test setup Test specimen (see clause 3) Test chamber
14、(see 2.1.1) 1/2 flame height (see 4.5) Burner (see 2.1.2) 30 305 mm (12.00 inches) Flammable material (see 2.2.1)12.7 mm (0.50 in) min Water12.7 mm (0.50 in) Metal pan ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health o
15、r technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephone No.:
16、 FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forwarded t
17、o Committee Chairman: Revision History Revision letter Project number Publication date Additions, changes and deletions - SP-4301 April 1999 Initial publication A SP-4782-R September 2000 B SP-5347.04 Change paragraph 2.1.6 to 2.1.5 In paragraph 4.3 change paragraph reference from 2.1.3 to 2.2.1 Revised text under paragraph 6 In figure 1 change dimension 104.8 mm to 305 mm to correct errorElectronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org
