1、 EIA STANDARD TP-114 Coupling and Uncoupling Force Test Procedure for Electrical Connectors, Sockets and Applicable Accessories EIA-364-114 October 2010 Electronic Components Industry Association EIA-364-114 ANSI/EIA-364-114-2010(R2017) Approved: October 11, 2010 Reaffirmed: June 19, 2017 NOTICE EIA
2、 Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the pro
3、per product for his particular need. Existence of such Specifications and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Specifications and Publications, nor shall the existence of such Specifications and P
4、ublications preclude their voluntary use by those other than ECIA members, whether the Specification is to be used either domestically or internationally. Specifications and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such ac
5、tion, ECIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Specification or Publication. This EIA Specification is considered to have International Standardization implications, but the International Electrotechnical Commission ac
6、tivity has not progressed to the point where a valid comparison between the EIA Specification and the IEC document can be made. This Specification does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user o
7、f this Specification to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5374, formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Sockets Standards) Published
8、 by Electronic Components Industry Association 2017 EIA Standards coupling and/or uncoupling torque 5.3 Rates of coupling and uncoupling 5.4 Description of full coupling EIA-364-114 Page 3 5.5 Lubrication or cleaning, if required 5.6 Wire type, gage and length, if applicable. Use of test boards, if
9、applicable 5.7 Applicable hardware 5.8 Torque requirements 5.9 Test conditions, if other than standard atmospheric 6 Test documentation Documentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description including part num
10、ber, if applicable 6.3 If applicable, fixturing, gage details and gage part number 6.4 Test equipment used, and date of last and next calibration 6.5 Values and observation 6.6 Description of coupling or confirmation of test sponsors instructions 6.7 Name of operator and start/finish date(s) of test
11、 6.8 Coupling and uncoupling rates Revision History Revision letter Project number Additions, changes and deletions SP-5207 ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appr
12、opriate information below and mail or FAX to: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change
13、 Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c.Reason/Rationale for Recomendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org
