1、EIASTANDARDTP-117Dielectric Breakdown Voltage Test Procedure for Electrical Connectors, Sockets and Coaxial Contacts EIA-364-117 November 2017 Electronic Components Industry Association EIA-364-117ANSI/EIA-364-117-2017 Approved: November 20, 2017NOTICEEIA Engineering Standards and Publications are d
2、esigned to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existenc
3、e of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than
4、 ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does
5、 it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is considered to have International Standardization implications, but the International Electrotechnical Commission activity has not progressed to the point where a valid comparison between the EIA
6、Standard and the IEC document can be made. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the
7、applicability of regulatory limitations before its use. (From Standards Proposal No. 5360, formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Sockets Standards.) Published by Electronic Components Industry Association 2017 EIA Standards see 2.1.5. 4.5.1 Number of c
8、ontacts (Only applicable to methods A, B and C) Unless otherwise specified in the referencing document, a minimum of three measurements (3 adjacent contacts and/or 3 contacts-to-shell and/or 3 contacts-to-base plate) per test specimen. 5 Details to be specified The following details shall be specifi
9、ed in the referencing document: 5.1 Special high voltage source, if applicable; see 2.1.1 5.3 Current surge limits, and limiting device, if applicable; see 2.1.1 5.4 Voltmeter accuracy, if other than at least 5 %; see 2.1.2 5.5 Leakage current if other than specified in 2.1.5 5.6 Define test specime
10、n (mated or unmated); see 3.1 5.7 Special preparations or conditions, if required; see 3.2 5.8 Method of connection of test voltage to specimen, if significant; see 3.2 5.9 Points of application of test voltage; see 4.1 5.10 Barometric pressure; see 4.2 5.10.1 Sea level or reduced pressure, if appli
11、cable; see 4.2 5.10.2 Test during and after subjection to reduced pressure; see 4.2.1 5.10.3 Method of mounting in test chamber; see 4.2.1 EIA-364-117 Page 5 5.11 Nature of potential (ac or dc); see 4.3 5.12 Examination and measurement of specimen, detail requirements (if required); see 4.5 5.13 Num
12、ber of specimens to be tested. 6 Test documentation Documentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description include fixturing 6.3 Test equipment used, and date of last and next calibration 6.4 Test procedure 6.
13、5 Values and observations 6.6 Name of operator and start/finish date(s) of test ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to
14、: Electronic Components Industry Association EIA Standards & Technology Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area:
15、 a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLYResponsible Committee: Chairman: Date comments forwarded to Committee Chairman: Revision History Revision letterProject numberPublication dateAdditions, changes and deletions - SP-5360 Initial publication Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org
