1、 EIA STANDARD TP-13E Mating and Unmating Force Test Procedure for Electrical Connectors and Sockets EIA-364-13E (Revision of EIA-364-13D) June 2011 Electronic Components Industry Association EIA-364-13E ANSI/EIA-364-13E-2011 (R2017) Approved: June 28, 2011 Reaffirmed: February 10, 2017 NOTICE EIA En
2、gineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper
3、 product for his particular need. Existence of such Specifications and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Specifications and Publications, nor shall the existence of such Specifications and Publ
4、ications preclude their voluntary use by those other than ECIA members, whether the Specification is to be used either domestically or internationally. Specifications and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such actio
5、n, ECIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Specification or Publication. This EIA Specification is considered to have International Standardization implications, but the International Electrotechnical Commission activ
6、ity has not progressed to the point where a valid comparison between the EIA Specification and the IEC document can be made. This Specification does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of t
7、his Specification to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5382.01, formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Sockets Standards) Published
8、 by Electronic Components Industry Association 2017 EIA Standards mating force, unmating force, or both 5.3 Rates of mating and unmating, if other than specified in 4.1.1.2, 4.1.2, 4.2.1.2 and 4.2.2 5.4 Depth of mating if applicable 5.5 Lubrication or cleaning, if required 5.6 Wire type, gage, and l
9、ength if applicable 5.7 Applicable hardware 5.8 Force requirements 5.9 Test conditions, if other than standard atmospheric 5.10 Applicable to method B only: Details of the device(s) or gage(s) to be used for mating/unmating to the connector/socket, as well as the method and frequency of cleaning, if
10、 required EIA-364-13E Page 4 6 Test documentation Documentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description including part number if applicable 6.3 If applicable, fixturing, gage details and gage part number 6.4
11、Test equipment used, and date of last and next calibration 6.5 Test procedure and method, if other than method A 6.6 Values and observation 6.7 Name of operator and start/finish date(s) of test EIA Document Improvement Proposal If in the review or use of this document, a potential change is made evi
12、dent for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Association Technology Strategy & Standards Department Publications Office 2500 Wilson Blvd., Suite 310 Arlington, VA 22201 FAX: (703-875-8908) Document No.: Docum
13、ent Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECA USE ONLY Responsible Commi
14、ttee: Chairman: Date comments forwarded to Committee Chairman: Revision History Revision letter Project number Additions, changes and deletions C SP-5136 Original test procedure is now method A. Added Method B and paragraph 2.1.4, 3.2, 4.2, 5.10 and 6.3. Revised paragraph 1.1, 4.1.1.2, 4.1.2, 5.2, 5
15、3, 6.2 and 6.5. D 5157 Added paragraph 1.2, 2.2 and socket to title. Revised paragraph 2.1 4, 4.1 and 4.2. E 5215 Revised paragraph 2.1.2, 2.1.3, 4.1.1.1, 4.1.1.2, 4.1.2 and 5.8 to remove the word torque. Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org
