1、 EIA STANDARD TP-19A Torsional Insert Retention Test Procedure for Electrical ConnectorsEIA-364-19A (Revision of EIA-364-19) April 2001 ANSI/EIA-364-19A-2001(R2015) Approved: April 10, 2001 Reaffirmed: March 23, 2015 EIA-364-19A NOTICE EIA Engineering Standards and Publications are designed to serve
2、 the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Existence of such Standa
3、rds and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those other than ECIA members, w
4、hether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, nor does it assume any o
5、bligation whatever to parties adopting the Standard or Publication. This standard is based upon the major technical content of International Electrotechnical Commission standard 512-8, test 15c, insert retention in housing (torsional), 1993-01, third edition. It conforms in all essential respects to
6、 this IEC standard. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regula
7、tory limitations before its use. (From Standards Proposal No. 4894 formulated under the cognizance of the CE-2.0 Committee on EIA National Connector and Socket Standards, and reaffirmed per Standards Proposal No. 5345.06). Published by Electronic Components Industry Association 2015 Standards & Tech
8、nology Department 2214 Rock Hill Road, Suite 265 Herndon, VA 20170 PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by the ECIA and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreemen
9、t. For information, contact: IHS 15 Inverness Way East Englewood, CO 80112-5704 or call USA and Canada (1-877-413-5184), International (303-397-7956) CONTENTS Clause 1 1.1 2 2.1 3 3.1 4 5 6 Introduction Scope Test resources . Equipment Test specimen . Preparation . Test procedure Details to be speci
10、fied Test documentation 1 1 1 2 2 2 3 1 (This page left blank) 11 EIA-364-19A Page 1 TEST PROCEDURE No. 19A TORSIONAL INSERT RETENTION TEST PROCEDURE FOR ELECTRICAL CONNECTORS (From EIA Standards Proposal No. 4894, formulated under the cognizance EIA CE-2.0 Committee on National Connector Standards,
11、 and previously published in EIA-364- 19.) 1 Introduction 1.1 Scope 1.1.1 This standard establishes test methods to determine the ability of the insert retaining system to withstand the torsional stresses likely to be encountered during normal usage. 1.2 Typical damage resulting rom this test might
12、be: 1.2.1 Cracked or broken inserts. 1.2.2 Inserts permanently displaced within connector shells. 2 Test resources 2.1 Equipment 2.1.1 Rigid mounting panel. 2.1.2 Test torque arm and suitable insert attachment fixture. 2.1.3 A suitable instrument (such as force scale, torque wrench, load scale or sp
13、ring scale) for measuring the applied load to an accuracy of k five percent. 2.1.4 A suitable arrangement capable of applying the torque at a steady rate of 0.050 newton meter per second (0.5 pound inch per second). 2.1.5 A suitable instrument capable of measuring insert location relative to connect
14、or shell. EU-364-19A Page 2 3 Test specimen 3.1 Preparation 3.1.1 The specimen shall be mounted in accordance with the referencing document. 3.1.2 Cable fitting and accessories shall not be mounted on the connector. 4 Test procedure 4.1 The connector shell shall be securely mounted to a rigid panel.
15、 Care should be taken to prevent distortion or stressing the shell in the mounting process. 4.2 The test torque arm shall be secured to the insert. 4.3 The specified torque shall be applied to the insert by the suitable test fixture. The torque shall be increased steadily at a rate of approximately
16、0.050 newton meter per second (0.5 pound inch per second) up to the specified value and held for one minute. 4.4 After the torque is released from the insert, the connector shall be examined for damage. 5 Details to be specified The following details shall be specified in the referencing document: 5
17、1 Preparation of the specimen 5.2 Mounting of the specimen 5.3 Details of the test fixture 5.4 Torque to be applied and applicable direction 5.5 Requirements for final measurements 5.6 Any deviation from the standard test method EIA-364-19A Page 3 6 Test documentation Documentation shall contain th
18、e details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description including fixturing and point of application 6.3 Test equipment used, and date of last and next calibration 6.4 Test and procedure 6.5 Values and observations 6.6 Name of operator and
19、date of test ECIA Document Improvement Proposal If in the review or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Association EIA Standards & Techno
20、logy Department 2214 Rock Hill Rd., Suite 265 Herndon, VA 20170 FAX: (571-323-0245) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reaso
21、n/Rationale for Recommendation: Additional Remarks: Signature: Date: FOR ECIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org
