1、 EIA STANDARD TP-34 Ambient Condensation Test Procedure for Electrical Connectors and Sockets EIA-364-34 April 2012 Electronic Components Industry Association EIA-364-34 ANSI/EIA-364-34-2012(R2017) Approved: April 21, 2012 Reaffirmed: August 21, 2017 NOTICE EIA Engineering Standards and Publications
2、 are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for his particular need. Ex
3、istence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their voluntary use by those othe
4、r than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability to any patent owner, no
5、r does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is considered to have International Standardization implication, but the International Electrotechnical Commission activity has not progressed to the point where a valid comparison between the
6、 EIA Standard and the IEC document can be made. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine
7、 the applicability of regulatory limitations before its use. (From Standards Proposal No. SP-5393.05 formulated under the cognizance of the CE-2.0 National Connector Standards Committee). Published by Electronic Components Industry Association 2017 EIA Standards see 4.3 5.3 Test conditions (length);
8、 see table 1 5.4 Polarizing voltage and load, the length of time, and points of application; see 4.5 5.5 Final measurement; see 4.7 5.5.1 At high humidity; see 4.7.1 5.5.2 During recovery period; see 4.7.2 5.5 3 After recovery period; see 4.7.3 5.6 Number of specimens to be tested 5.7 Define test sp
9、ecimen, mated or unmated 5.8 Wire type, size, and sealing plugs, if applicable; see 3.2 6 Documentation Documentation shall contain the details specified in clause 5, with any exceptions, and the following: 6.1 Title of test 6.2 Specimen description including fixturing; if applicable 6.3 Test equipm
10、ent used, and date of last and next calibration 6.4 Test procedure and duration 6.5 Values and observations, initial and final ambient conditions 6.6 Name of operator and start/finish date(s) of test EIA-364-34 Page A-1 Annex A Previous designations (Informative) This informative annex is provided a
11、s a cross reference to the designations previously contained in EIA-364-31 and MIL-STD-1344, method 1002.2. Table A.1 Test condition designation EIA-364-34 designation Previous EIA-364-31 designations MIL-STD-1344, method 1002.2 designations Condition A Condition A Condition B Condition B Condition
12、B Condition A Condition C Condition C Condition C Condition D Condition D Condition D Condition E Condition E - Table A.2 Test method designation EIA-364-34 designation Previous EIA-364-31 designation MIL-STD-1344, method 1002.2 designation - Method I - ECIA Document Improvement Proposal If in the r
13、eview or use of this document, a potential change is made evident for safety, health or technical reasons, please fill in the appropriate information below and mail or FAX to: Electronic Components Industry Association Technology Strategy & Standards Department Publications Office 2214 Rock Hill Roa
14、d, Suite 170 Herndon, VA 20170-4212 FAX: (571 323 0245) Document No.: Document Title: Submitters Name: Telephone No.: FAX No.: e-mail: Address: Urgency of Change: Immediate: At next revision: Problem Area: a. Clause Number and /or Drawing: b. Recommended Changes: c. Reason/Rationale for Recommendati
15、on: Additional Remarks: Signature: Date: FOR EIA USE ONLY Responsible Committee: Chairman: Date comments forwarded to Committee Chairman: Revision History Revision letter Project number Additions, changes and deletions SP-5211 This standard was previously identified as EIA-364-31, method I. Electronic Components Industry Association 2214 Rock Hill Road, Suite 265 * Herndon, VA 20170 * tel 571-323-0294 * fax 571-323-0245 www.ecianow.org
