ECA EIA-60384-11-2014 Fixed Capacitors for Use in Electronic Equipment - Part 11 Sectional Specification - Fixed Polyethylene-Terephthalate Film Dielectric Metal Foil d c Capacitor.pdf

上传人:Iclinic170 文档编号:704421 上传时间:2019-01-03 格式:PDF 页数:30 大小:264.42KB
下载 相关 举报
ECA EIA-60384-11-2014 Fixed Capacitors for Use in Electronic Equipment - Part 11 Sectional Specification - Fixed Polyethylene-Terephthalate Film Dielectric Metal Foil d c Capacitor.pdf_第1页
第1页 / 共30页
ECA EIA-60384-11-2014 Fixed Capacitors for Use in Electronic Equipment - Part 11 Sectional Specification - Fixed Polyethylene-Terephthalate Film Dielectric Metal Foil d c Capacitor.pdf_第2页
第2页 / 共30页
ECA EIA-60384-11-2014 Fixed Capacitors for Use in Electronic Equipment - Part 11 Sectional Specification - Fixed Polyethylene-Terephthalate Film Dielectric Metal Foil d c Capacitor.pdf_第3页
第3页 / 共30页
ECA EIA-60384-11-2014 Fixed Capacitors for Use in Electronic Equipment - Part 11 Sectional Specification - Fixed Polyethylene-Terephthalate Film Dielectric Metal Foil d c Capacitor.pdf_第4页
第4页 / 共30页
ECA EIA-60384-11-2014 Fixed Capacitors for Use in Electronic Equipment - Part 11 Sectional Specification - Fixed Polyethylene-Terephthalate Film Dielectric Metal Foil d c Capacitor.pdf_第5页
第5页 / 共30页
点击查看更多>>
资源描述

1、 EIA STANDARD Fixed Capacitors for Use in Electronic Equipment Part 11: Sectional Specification Fixed Polyethylene-Terephthalate Film Dielectric Metal Foil d.c. CapacitorsEIA-60384-11 (IEC 60384-11:2008, IDT) October 2014 ANSI/EIA-60384-11-2014 Approved: October 10, 2014 EIA-60384-11NOTICE EIA Engin

2、eering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper pr

3、oduct for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude

4、their voluntary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any

5、liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 60384-11:2008: Fixed Capacitors for Use in Electronic Equipment Part 11: Sectional Specifica

6、tion Fixed Polyethylene-Terephthalate Film Dielectric Metal Foil d.c. Capacitors. This document is the EIA Standard EIA-60384-11 2014: Fixed Capacitors for Use in Electronic Equipment Part 11: Sectional Specification Fixed Polyethylene-Terephthalate Film Dielectric Metal Foil d.c. Capacitors. The te

7、xt, figures and tables of IEC 60384-11:2008 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). These materials are subject to copyright claims of IEC and ECIA. No part of this publication may be reproduced in any form, including an electronic

8、retrieval system, without the prior written permission of ECIA. All requests pertaining to EIA-60384-11 2014: Fixed Capacitors for Use in Electronic Equipment Part 11: Sectional Specification Fixed Polyethylene-Terephthalate Film Dielectric Metal Foil d.c. Capacitors should be submitted to ECIA at t

9、he address below. The IEC copyrighted material has been reproduced with permission from ANSI. The IEC Foreword and Introduction are not part of the requirements of this standard but are included for information purposes only. This Standard does not purport to address all safety problems associated w

10、ith its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5281, formulated under the cogni

11、zance of the P-2.2 Committee on EIA Paper, Film, Mica any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates

12、closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the re

13、levant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that th

14、e technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maxim

15、um extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible

16、 for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical com

17、mittees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publicat

18、ions. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of pat

19、ent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-11 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This third edition cancels and replaces the second edition published in

20、 1988 and constitutes a minor revision related to tables, figures and references. This bilingual version (2011-11) corresponds to the monolingual English version, published in 2008-02. The text of this standard is based on the following documents: CDV Report on voting 40/1839/CDV 40/1864/RVCEIA-6038

21、4-11 Page 2 Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. The French version of this standard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The list o

22、f all parts of the IEC 60384 series, under the (new) general title Fixed capacitors for use in electronic equipment, can be found on the IEC web site. The QC number that appears on the front cover of this publication is the specification number in the IEC Quality Assessment System for Electronic Com

23、ponents (IECQ). The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, with

24、drawn, replaced by a revised edition, or amended. EIA-60384-11 Page 3 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 11: Sectional specification Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors 1 General 1.1 Scope This part of IEC 60384 applies to fixed direct curre

25、nt capacitors, for rated voltages not exceeding 6 300 V, using as dielectric a polyethylene-terephthalate film and electrodes of thin metal foils. For capacitors with rated voltages exceeding 1 000 V, additional tests and requirements may be specified in the detail specification. The capacitors cove

26、red by this standard are intended for use in electronic equipment. NOTE Capacitors for radio interference suppression are not included, but are covered by IEC 60384-14 (see bibliography). 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from

27、IEC 60384-1, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring to this sectional specification shall be of equal or higher

28、performance level, because lower performance levels are not permitted. 1.3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the reference

29、d document (including any amendments) applies. IEC 60062, Marking codes for resistors and capacitors IEC 60063, Preferred number series for resistors and capacitors1)IEC 60068-1, Environmental testing Part 1: General and guidance IEC 60384-1:1999, Fixed capacitors for use in electronic equipment Par

30、t 1: Generic specification IEC 60410:1973, Sampling plans and procedures for inspection by attributes ISO 3: Preferred numbers Series of preferred numbers. 1.4 Information to be given in a detail specification Detail specifications shall be derived from the relevant blank detail specification. 1) Se

31、cond edition (1963) incorporating Amendments 1 (1967) and 2 (1977). EIA-60384-11 Page 4 Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detai

32、l specification and indicated in the test schedules, for example by an asterisk. NOTE The information given in 1.4.1 may, for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall preferably be selected from those

33、 given in the appropriate clause of this sectional specification. 1.4.1 Outline drawing and dimensions There shall be an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and their associated tolerances, which affect interchangeab

34、ility and mounting, shall be given in the detail specification. All dimensions shall preferably be stated in millimetres, however, when the original dimensions are given in inches, the converted metric dimensions in millimetres shall be added. Normally the numerical values shall be given for the len

35、gth of the body, the width and height of the body and the wire spacing, or for cylindrical types, the body diameter, and the length and diameter of the terminations. When necessary, for example when a number of items (capacitance values/voltage ranges) are covered by a detail specification, the dime

36、nsions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the detail specification shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on printe

37、d boards, this shall be clearly stated in the detail specification. 1.4.2 Mounting The detail specification shall specify the method of mounting to be applied for normal use and for the application of the vibration and the bump or shock tests. The capacitors shall be mounted by their normal means. T

38、he design of the capacitor may be such that special mounting fixtures are required in its use. In this case the detail specification shall describe the mounting fixtures and they shall be used in the application of the vibration and bump or shock tests. 1.4.3 Ratings and characteristics The ratings

39、and characteristics shall be in accordance with the relevant clauses of this specification, together with the following: 1.4.3.1 Rated capacitance range See 2.2.1. NOTE When products approved to the detail specification have different ranges, the following statement should be added: “The range of va

40、lues available in each voltage range is given in the qualified products list“. 1.4.3.2 Particular characteristics Additional characteristics may be listed, when they are considered necessary to specify adequately the component for design and application purposes. 1.4.3.3 Soldering The detail specifi

41、cation shall prescribe the test methods, severities and requirements applicable for the solderability and the resistance to soldering heat test. EIA-60384-11 Page 5 1.4.4 Marking The detail specification shall specify the content of the marking on the capacitor and on the package. Deviations from 1.

42、6 of this sectional specification, shall be specifically stated. 1.5 Terms and definitions For the purposes of this document the terms and definitions of IEC 60384-1, as well as the following apply. 1.5.1 rated voltage (UR) maximum d.c. voltage which may be applied continuously to a capacitor at the

43、 rated temperature NOTE The sum of the d.c. voltage and the peak a.c. voltage applied to the capacitor shall not exceed the rated voltage. The value of the peak a.c. voltage shall not exceed the following percentages of the rated voltage at the frequencies stated and shall not be greater than 280 V,

44、 50 Hz 20 % 100 Hz 15 % 1 000 Hz 3 % 10 000 Hz 1 % unless otherwise specified in the detail specification. 1.6 Marking See 2.4 of IEC 60384-1, with the following details: 1.6.1 The information given in the marking is normally selected from the following list. The relative importance of each item is

45、indicated by its position in the list: a) rated capacitance (in clear or code according to IEC 60062); b) rated voltage (d.c. voltage may be indicated by the symbol or ); c) tolerance on rated capacitance; d) category voltage; e) year and month (or week) of manufacture; f) manufacturers name or trad

46、e mark; g) climatic category; h) manufacturers type designation; i) reference to the detail specification. 1.6.2 The capacitor shall be clearly marked with a), b) and c) above and with as many as possible of the remaining items as is considered necessary. Any duplication of information in the markin

47、g on the capacitor should be avoided. 1.6.3 The package containing the capacitor(s) shall be clearly marked with all the information listed in 1.6.1. 1.6.4 Any additional marking shall be so applied that no confusion can arise. EIA-60384-11 Page 6 2 Preferred ratings and characteristics 2.1 Preferre

48、d characteristics The values given in detail specifications shall preferably be selected from the following: 2.1.1 Preferred climatic categories The capacitors covered by this specification are classified into climatic categories according to the general rules given in IEC 60068-1. NOTE For the test

49、s in the IEC 60068 series of publications, the editions referenced in the applicable test clauses of the generic specification are used. The lower and upper category temperatures and the duration of the damp heat, steady state test shall be chosen from the following. Lower category temperature: 55 C, 40 C and 25 C. Upper category temperature: +85 C, +100 C, +105 C and +125 C. Duration of the damp heat, steady state test: 4, 10, 21 and 56 days. The severities for the cold and dry heat tests are the lower and upper category temperature

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1