1、 EIA STANDARD Fixed Capacitors for Use in Electronic Equipment Part 13: Sectional Specification Fixed Polypropylene Film Dielectric Metal Foil d.c. Capacitors EIA-60384-13 (IEC 60384-13:2011, IDT) October 2014 ANSI/EIA-60384-13-2014 Approved: October 10, 2014 EIA-60384-13 NOTICE EIA Engineering Stan
2、dards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for h
3、is particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards and Publications preclude their volun
4、tary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, ECIA does not assume any liability t
5、o any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 60384-13:2011: Fixed Capacitors for Use in Electronic Equipment Part 13: Sectional Specification Fixed
6、Polypropylene Film Dielectric Metal Foil d.c. Capacitors. This document is the EIA Standard EIA-60384-13 2014: Fixed Capacitors for Use in Electronic Equipment Part 13: Sectional Specification Fixed Polypropylene Film Dielectric Metal Foil d.c. Capacitors. The text, figures and tables of IEC 60384-1
7、3:2011 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). These materials are subject to copyright claims of IEC and ECIA. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior w
8、ritten permission of ECIA. All requests pertaining to EIA-60384-13 2014: Fixed Capacitors for Use in Electronic Equipment Part 13: Sectional Specification Fixed Polypropylene Film Dielectric Metal Foil d.c. Capacitors should be submitted to ECIA at the address below. The IEC copyrighted material has
9、 been reproduced with permission from ANSI. The IEC Foreword and Introduction are not part of the requirements of this standard but are included for information purposes only. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requireme
10、nts. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5279, formulated under the cognizance of the P-2.2 Committee on EIA Paper, Film, M
11、ica any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for St
12、andardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has
13、 representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurat
14、e, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional
15、publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some
16、 areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents in
17、cluding individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or re
18、liance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the
19、 elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60384-13 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This fourth
20、edition cancels and replaces the third edition published in 2006 and contains the following significant technical changes with respect to the previous edition. Table 3, Sampling plan together with numbers of permissible non-conformance for qualification approval test, has been adjusted. Table 5, Lot
21、-by-lot inspection, has been changed, highlighting assessment level EZ only. Table 6, Periodic inspection, has been changed, highlighting assessment level EZ only. EIA-60384-13 Page 2 The text of this standard is based on the following documents: FDIS Report on voting 40/2130/FDIS 40/2143/RVD Full i
22、nformation on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC directives, Part 2. A list of all the parts of the IEC 60384 series, under the general title Fixed capacitors
23、 for use in electronic equipment, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date,
24、 the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. EIA-60384-13 Page 3 FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 13: Sectional specification Fixed polypropylene film dielectric metal foil d.c. capacitors 1 General 1.1 Scope This part of IEC 60384
25、applies to fixed direct current capacitors, using as dielectric a polypropylene film with electrodes of thin metal foils. The capacitors covered by this standard are intended for use in electronic equipment. Capacitors for electromagnetic interference suppression are not included, but are covered by
26、 IEC 60384-14. 1.2 Object The object of this standard is to prescribe preferred ratings and characteristics and to select from IEC 60384-1, the appropriate quality assessment procedures, tests and measuring methods, and to give general performance requirements for this type of capacitor. Test severi
27、ties and requirements prescribed in detail specifications referring to this sectional specification are of at least equal or higher performance level, because lower performance levels are not permitted. 1.3 Normative references The following referenced documents are indispensable for the application
28、 of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60063:1963, Preferred number series for resistors and capacitors Amendment 1 (1967) Amendment 2 (1977) IEC 60068-1, E
29、nvironmental testing Part 1:General and guidance IEC 60384-1:2008, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60384-13-1, Fixed capacitors for use in electronic equipment Part 13-1: Blank detail specification Fixed polypropylene film dielectric metal foil d.c.
30、 capacitors Assessment level E and EZ IEC 60384-14, Fixed capacitors for use in electronic equipment Part 14: Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains IEC 60410:1973, Sampling plans and procedures for inspection by attr
31、ibutes IEC 61193-2, Quality assessment systems Part 2: Selection and use of sampling plans for inspection of electronic components and packages ISO 3, Preferred numbers Series of preferred numbers EIA-60384-13 Page 4 1.4 Information to be given in a detail specification Detail specifications shall b
32、e derived from the relevant blank detail specification. Detail specifications shall not specify requirements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in
33、 the test schedules, for example by an asterisk. NOTE The information given in 1.4.1 may, for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall preferably be selected from those given in the appropriate clause
34、 of this sectional specification. 1.4.1 Outline drawing and dimensions These shall be an illustration of the capacitor as an aid to easy recognition and for comparison of the capacitor with others. Dimensions and their associated tolerances, which affect interchangeability and mounting, shall be giv
35、en in the detail specification. All dimensions shall preferably be stated in millimetres. Normally, the numerical values shall be given for the length, the width and height of the body and the wire spacing, or for cylindrical types, the body diameter, and the length and diameter of the terminations.
36、 When necessary, for example, when a number of items (capacitance values/voltage ranges) are covered by a detail specification, the dimensions and their associated tolerances shall be placed in a table below the drawing. When the configuration is other than described above, the detail specification
37、shall state such dimensional information as will adequately describe the capacitor. When the capacitor is not designed for use on printed boards, this shall be clearly stated in the detail specification. 1.4.2 Mounting The detail specification shall specify the method of mounting to be applied for n
38、ormal use and for the application of the vibration and the bump or shock tests. The capacitors shall be mounted by their normal means. The design of the capacitor may be such that special mounting fixtures are required in its use. In this case, the detail specification shall describe the mounting fi
39、xtures and they shall be used in the application of the vibration and bump or shock tests. 1.4.3 Rating and characteristics The ratings and characteristics shall be in accordance with the relevant clauses of this specification, together with the following. 1.4.3.1 Particular characteristics Addition
40、al characteristics may be listed, when they are considered necessary to specify adequately the component for design and application purposes. 1.4.3.2 Soldering The detail specification shall prescribe the test methods, severities and requirements applicable for the solderability and the resistance t
41、o solder heat test. EIA-60384-13 Page 5 1.4.4 Marking The detail specification shall specify the content of the marking on the capacitor and on the package. Deviations from 1.6 of this sectional specification shall be specifically stated. 1.5 Terms and definitions For the purpose of this document, t
42、he terms and definitions given in IEC 60384-1 and the following apply. 1.5.1 stability class tolerance on the temperature coefficient together with the permissible change of capacitance after defined tests NOTE 1 The stability class is stated in the detail specification. NOTE 2 Table 2 shows the pre
43、ferred stability classes. 1.5.2 rated voltage URmaximum d.c. voltage which may be applied continuously to a capacitor at the rated temperature NOTE The sum of the d.c. voltage and the peak a.c. voltage applied to the capacitor should not exceed the rated voltage. The value of the peak a.c. voltage s
44、hould not exceed the following percentages of the rated voltage at the frequencies stated and should be not greater than 280 V: 50 Hz: 20 %100 Hz: 15 % 1 000 Hz: 3 % 10 000 Hz: 1 % unless otherwise specified in the detail specification. 1.6 Marking See IEC 60384-1, 2.4 with the following details. 1.
45、6.1 General The information given in the marking is normally selected from the following list; the relative importance of each item is indicated by its position in the list. nominal capacitance; rated voltage (d.c. voltage may be indicated by the symbol or ); tolerance on nominal capacitance; year a
46、nd month (or week) of manufacture; manufacturers name or trade mark; temperature coefficient and stability class; climatic category; manufacturers type designation; reference to the detail specification; EIA-60384-13 Page 6 1.6.2 Marking of capacitors The capacitor shall be clearly marked with a), b
47、) and c) of 1.6.1 and with as many as possible of the remaining items as is considered necessary. Any duplication of information in the marking on the capacitor should be avoided. 1.6.3 Marking of packaging The package containing the capacitor(s) shall be clearly marked with all the information list
48、ed in 1.6.1. 1.6.4 Additional marking Any additional marking shall be so applied that no confusion can arise. 2 Preferred ratings and characteristics 2.1 Preferred characteristics The values given in detail specifications shall preferably be selected from the following. 2.1.1 Preferred climatic cate
49、gories The capacitors covered by this specification are classified into climatic categories according to the general rules given in IEC 60068-1. The lower and upper category temperatures and the duration of the damp heat, steady-state test shall be chosen from the following: Lower category temperature: 55 C, 40 C, 25 C and 10 C Upper category temperature: +85 C , +100 C and +105 C Duration of the damp heat, steady-state test: 10, 21 and 56 days The severities for the cold and dry heat tests are the
